Consort LST500 Manuel

66000414

Iss 01

ODEL

ILLIMETRES

ATTS

A B C D/E

LST500 500 830 430 616 107

LST800 800 1183 430 952 115

ONTROLS

When the appliance is connected to the mains supply and the wall socket is switched ‘ON’ the mains neon indicator on the front panel of

the heater will light, showing that the power is available to the unit.

EATERS FOR

IRELESS CONTROLS

(RF Models only)

For the

‘RF’

models please follow instructions supplied with the

wireless controller. Please note ‘RF’ models the heater will not work without

the controller CZC1.

EATERS

ANUAL CONTROLS

(Standard and T Models)

The controls (except RF models) are located behind a cover on the right

hand end of the appliance.

The heaters (except the W models) are fitted with a built-in thermostat to

control the temperature of the room. The thermostat adjustment knob is

located on the right hand end and is numbered. Rotate the knob clockwise to

a higher number to raise the room temperature. Once set it is unlikely to

require to be touched again.

To set the heater to the Frost Watch mode, turn the thermostat control knob

fully anti-clockwise until the frost symbol aligns with the reference mark.

The heat switch located on the bottom of the control panel turns the heat

on and off.

SING THE

IMER

(T Models only)

The heater must be connected to the mains supply in order for the timer to

operate continuously.

Set the correct time on the timer by rotating the dial clockwise until the

correct time is aligned with the timer reference mark on the 24-hour clock

face.

UTOMATIC

PERATION

Move the switch immediately beneath the timer to the auto position

designated

1. The 24-hour timer can be set to give any combination of On/Off

intervals to a minimum of 20 minutes on. Select the ‘On’ time required

by pressing the black segment (on the circumference of the timer)

adjacent to the time required outwards. This will cause the heater to

switch ‘On’ at the selected time for 20 minutes operation. Each

additional segment pressed out will give a further 20 minutes of

operation. In this way, select the length of time required for the unit to

be ‘On’ and push out the number of 20-minute segments necessary to

select the time period required.

2. The timer can be set to give as many ‘On’ periods as required during

any 24-hour period.

3. This program will repeat itself every 24 hours until changed. This

program may be overridden at any time by switching to manual

operation.

ANUAL

PERATION

Move the slider switch immediately beneath timer to the manual position

designated . The heater will now run continuously, controlled by the

heat settings and thermostat as described under ‘Controls’.

HERMALLY

PERATED

OUT

For your safety the appliance is fitted with two over temperature cut-outs. These are safety devices, which switch the heater off if, for

any reason, the appliance overheats. It can only be re-set after the appliance has cooled down. In order to re-set the cut-outs, proceed as

follows:

•Switch off appliance and leave for approximately 15 minutes.

•Ensure the heater is not covered or the air intake is blocked. Switch appliance back on.

•Ensure that the appliance is functioning correctly. If the cut-outs operate again, the appliance should be checked by a competent

electrician.

The heater carries a ‘Do Not Cover’ label to warn the user that if the appliance is covered, there is a risk of overheating.



Selector

Switch

Thermostat

adjustment

knob

Heat on/off

Switch

Timer

reference

mark

Thermostat

reference

mark

NB: On the non-timer models there is

no timer control and selector switch.

66000414

Iss 01

OUNTING

To Wall Mount,

the wall bracket supplied must be used.

1. Remove the wall bracket from the heater, with the chains attached, by removing the 2 securing screws from the top of the rear panel.

2. Fix the wall bracket to the wall using 4 screws.

3. Fig 1: Present the heater to the bracket

4. Fig 2: Locate the heater onto the bottom lugs via the 2 slots in rear panel. Hinge the heater upwards and reattach the chain assembly, then

move the heater to the upright position. The link plates should slide under the slotted bracket lip.

5. Fig 3: Tighten both retaining screws.

The heater must not be located immediately below a fixed socket outlet.

LEANING

Always disconnect the heater from the mains before cleaning.

The heater should not require any maintenance, but it is strongly advised that it is kept clean. An occasional wipe over with a soft

cloth is all that should be necessary.

•Do NOT use metal or furniture polish on any part of the heater

•Do NOT touch the heater with wet hands or in any way bring water into contact with it.

If the supply cord is damaged, it must be replaced by the manufacturer or its service agent or a similarly qualified person in order

to avoid a hazard.

AFETY

The heaters have been designed to have a low surface temperature. This means it is safe to touch the heater when it is in

operation. The surface temperature of any part of the heater will not exceed a temperature of 43ºC as specified in the NHS Estates

Health Guidance notes on surface temperatures.

!!! WARNING !!! DO NOT COVER THE HEATER The surface temperature will exceed 43

C for a short period of time

when the heater is covered or the airflow around the heater is restricted in any way. If this happens the safety over temperature cut-

outs will turn the heater off.

This equipment has been designed and manufactured to the highest international standards

, but, like all electrical appliances which are

operated by mains voltage, care must be taken if you are to obtain the best results and safety is to be assured.

The appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities or lack

of experience and knowledge unless they have been given supervision or instruction concerning use of the appliance by a person

responsible for their safety.

Children should be supervised to ensure that they do not play with the appliance.

•Do NOT site the appliance into a corner.

•Ensure that nothing is pushed into any aperture of this appliance.

•Do NOT cover or restrict any aperture of the appliance when in use.

•Do NOT use the appliance if damaged.

•If used in a bathroom, the heater is to be installed so that the switches and other controls cannot be touched by a person in the

bath or shower.

This appliance meets the requirements of EU Directive 89/336 for EMC.

NOTE: The rating label can be viewed by loosening the two mounting bracket screws and hinging the appliance forward on its

retaining chains.

OUR

EATER

OES

ORK

•Check that power is available to the heater. The neon in the control switch should be illuminated.

•Check that the thermal cut-out has not operated. Follow the reset instructions given under the section headed ‘Thermal

Operated Cut-out’.

•Do not attempt to repair the heater.





 01646 692172 Mon to Fri 8.30 am to 3.30 pm

Consort Equipment Products Limited

Thornton Industrial Estate, ilford Haven, Pembrokeshire, SA73 2RT

Tel: 01646 692172 Fax: 01646 695195

Email: enquiri[email protected]m Web: www.consortepl.com

UALITY

PACE

EATERS

NSTALLATION

PERATION AND

AINTENANCE

NSTRUCTIONS FOR

LOW SURFACE TE PERATURE

PANEL CONVECTOR HEATERS

LEASE RETAIN THIS LEAFLET FOR FUTURE AINTENANCE

Catalogue Numbers:

LST500, LST500TI, LST500RF

LST800, LST800TI, LST800RF

Please note: ‘TI’ suffix in the model number denotes Timer models,

‘RF’ suffix denotes models for Wireless controls

Ce manuel convient aux modèles suivants

Autres manuels Consort Chauffage

Consort

Consort CHELSEA WMHW3 Manuel

Consort

Consort PLSTi050E Manuel d'utilisation et d'entretien

Consort

Consort PLSTi Series Manuel d'utilisation et d'entretien

Consort

Consort LST500SL Manuel d'utilisation et d'entretien

Consort

Consort PLE050MWIFI Manuel d'utilisation et d'entretien

Consort

Consort HE6502SL Manuel d'utilisation et d'entretien

Consort

Consort CN2MLSTiE Manuel d'utilisation et d'entretien

Consort

Consort PLSTi150RX Manuel d'utilisation et d'entretien

Consort

Consort PSL050/SS Manuel d'utilisation et d'entretien

Consort

Consort LST500EWIFI Manuel d'utilisation et d'entretien

Consort

Consort PLSTi100 Manuel utilisateur

Consort

Consort PVE050 Manuel d'utilisation et d'entretien

Consort

Consort CSL2LST Manuel d'utilisation et d'entretien

Consort

Consort CN2FSLT Manuel d'utilisation et d'entretien

Consort

Consort PLE200/SS Manuel utilisateur

Consort

Consort Heatflow BFH2T Instructions d'installation et d'utilisation

Consort

Consort PLE050RF Manuel d'utilisation et d'entretien

Consort

Consort PLSTi100RX Manuel d'utilisation et d'entretien

Consort

Consort CN2LSTRX Manuel utilisateur

Consort

Consort CSL2SC Manuel d'utilisation et d'entretien

Consort

Consort CN1LSTRX Instructions d'utilisation d'origine

Consort

Consort PRX050SS Manuel d'utilisation et d'entretien

Consort

Consort CSL2LST Instructions d'utilisation d'origine

Consort

Consort Heatflow BHM1 Manuel utilisateur

Manuels Chauffage populaires d'autres marques

oventrop

oventrop Regucor Series Manuel utilisateur

Blaze King

Blaze King CLARITY CL2118.IPI.1 Manuel utilisateur

ELMEKO

ELMEKO ML 150 Manuel utilisateur

BN Thermic

BN Thermic 830T Manuel utilisateur

KING

KING K Series Mode d’emploi

Empire Comfort Systems

Empire Comfort Systems RH-50-5 Guide de démarrage rapide

Well Straler

Well Straler RC-16B Manuel utilisateur

EUROM

EUROM 333299 Manuel utilisateur

Heylo

Heylo K 170 Manuel utilisateur

Eterna

Eterna TR70W Manuel utilisateur

Clarke

Clarke GRH15 Mode d’emploi

IRSAP

IRSAP The Radiator Company Ovali Manuel utilisateur

Empire Heating Systems

Empire Heating Systems WCC65 Manuel utilisateur

Wetekom

Wetekom 92 86 43 Manuel utilisateur

Desa

Desa SPC170-F Manuel utilisateur

Watlow

Watlow Watrod Electric Tubular Heaters Manuel utilisateur

Haverland

Haverland ECO-DRY GPS Series Manuel de la liste des pièces

Stelpro

Stelpro ASILVC2060 Series Manuel utilisateur