Comnet CWFE2SC2 Manuel utilisateur

INSTALLATION AND OPERATION MANUAL

CWFE2SC(M)(S)2

COMMERCIAL GRADE 10/100 MBPS

ETHERNET 2 PORT MEDIA CONVERTER

1 CHANNEL: ELECTRICAL OPTICAL

V1.25 – October 2010

The ComWorx™ VL CWFE2SC(M)(S)2 Ethernet 2 port media converters are designed to transmit

and receive 10/100 Mbps data over multimode or single mode optical fiber. The electrical

interface will Auto-Negotiate to a 10 Mbps, or 100 Mbps Ethernet rate without any adjustments.

The optical interface operates at a 100 Mbps Ethernet rate. These media converters are

commercial grade for light industrial use.

Content

Introduction ......................................................1

Features ......................................................................................................... 2

Package Contents.......................................................................................... 2

Hardware Description......................................3

Front Panel..................................................................................................... 3

Ports............................................................................................................... 3

LED Indicators................................................................................................ 4

DIP-switch...................................................................................................... 5

Rear Panel...................................................................................................... 6

Cabling ........................................................................................................... 6

Problem Solving ...............................................7

Optical Fiber Specification ..............................8

Technical Specifications .................................9

Introduction

The ComNet CWFE2SC(M)(S)2 is a cost-effective solution for converting

10/100Base-TX electrical to and 100Base-FX fiber optic cable, It allows you

to extend the distance of your 100Base-FX network up to 2 kilometers for

multi-mode fiber or up to 30 kilometers for single-mode fiber. The ComNet

CWFE2SC(M)(S)2 gives you the option of choosing between the most

popular fiber cabling connectors: SC/multi-mode fiber connector and SC

single-mode fiber connectors. The CWFE2SC(M)(S)2 module provides you

with one fiber connector for your fiber optic cable and one Ethernet RJ45

port (Auto MDI/MDIX) for your 100BaseTX copper cable connection. There

are 4 DIP- switches to set the operation mode for UTP, Fiber ports and link

loss forwarding function.

Features

ComNet CWFE2SC(M)(S)2

Complies with IEEE 802.3, 802.3u, and 802.3x standards.

Converts between UTP cabling and fiber-optic cable.

One RJ45 connector, Auto-MDI/MDIX for UTP port.

Supports 10/100 Mbps Auto-negotiation for UTP port.

Fiber optic cabling connectivity up to 30Km.

Store-and-forward switching architecture.

One SC fiber connector for 100Base-FX optical transmission.

4DIP-switches to set the operation mode and Link- Lost-Forwarding

function.

6 LEDs for per port: 100, Link, Activity, Full, Collision, and per unit

Power.

External DC power adapter 12V/1A.

FCC Class A, CE, UL, and CUL Mark certification

Package Contents

Stand-alone converter module package contains following items.

Media Converter

AC-DC Power Adapter

User Guide

Compare the contents of your converter module with the checklist above. If

any item is damaged or missing, please contact your local dealer for service.

Hardware Description

Unit dimension (L x W x H) is: 119mm x 85mm x 26mm

Front Panel

The Front Panel of the ComNet CWFE2SC(M)(S)2 consists of one RJ45

Port (Auto MDI/MDIX), 6 LED Indicators (UTP 100, LK/ACT, FDX/COL, Fiber

LK/ACT, FDX/COL and PWR) and one fiber 100Base-FX Port.

Ports

RJ45 Port (Auto MDI/MDIX): the Ethernet RJ45 will auto-sense for

10Base-T or 100Base-TX connections. Auto MDI/MDIX means that you

can connect to another switch or workstation without changing

non-crossover or crossover cabling.

Fiber Port: This port is for 100 Base-FX connections.

Fast Fiber Converter Module-- SC

LED Indicators

There are 6 diagnostic LEDs located on the Front panel of the media

converter. They provide real-time information of system and optional status.

The indicator includes Power, UTP 100, LK/ACT, FDX/COL, Fiber LK/ACT,

FDX/COL. The following table provides description of the LED status and

their meanings.

LED

Status

Meaning

PWR

Green

Power on

Green

100Mbps UTP Speed

100

OFF

10Mbps UTP Speed

Green

The unit is linking with its link partner.

Blinks

The unit is transmitting or receiving packets from UTP

devices.

LK/ACT

(UTP)

Off

No device attached

Green

The unit is linking with the corresponding unit.

Blinks

The unit is transmitting or receiving packets from FX

devices.

LK/ACT

(Fiber)

Off

No device attached

Orange

The UTP port is operating in full-duplex mode.

Blinks

Collision of Packets is occurring in the port.

FDX/COL

(UTP)

Off

Half-duplex mode or no device attached

Orange

The fiber port is operating in full-duplex mode.

Blinks

Collision of Packets is occurring in the port.

FDX/COL

(Fiber)

Off

Half-duplex mode or no device attached

DIP-switch

The DIP-switch is used to configure operation mode for LLF (Link Lost

Forwarding) and operation mode for UTP/Fiber port. The default value of

DIP switch is OFF.

S/W No

Status

Description

UTP 100Mbps Full Duplex mode

OFF

UTP Auto-Negotiate

Fiber in Half Duplex

OFF

Fiber in Full Duplex

LLF Enable

OFF

LLF Disable

Pure converter mode

OFF

Switch Converter mode

Link Lost Forwarding (DIP-Switch 3): When LLF is enabled, it allows UTP

link failures to be reported to the fiber side and also allows a fiber link failure

to be reported to the UTP side. Therefore, a link loss forward feature is

provided in both UTP and fiber side.

Pure Converter mode (DIP-Switch 4): When the pure converter mode is

enabled (on), it operates with minimal latency. The transmission flow does

not wait until the entire frame is ready, but instead it forwards the received

data immediately after the data has been received. The UTP port should be

forced at 100M in this application. When DIP-Switch is in Switch Converter

mode (off), the converter function is same as Switch Hub.

[Note] Do not change the DIP-switch setting when UTP or fiber port is

transmitting or receiving data. It may cause some data errors. If you change

the DIP-switch setting, please power off the converter and power it on again

to make the setting effective.

Rear Panel

The rear panel contains a power socket, which accepts 8–24 VDC @ 220mA.

Cabling

For the Twisted-pair segment unshielded twisted pair (UTP) or shielded

twisted pair (STP) cabling can be used. The cable must comply with the

IEEE 802.3u 100Base TX standard for Category 5. The cable between

the converter and the link partner (switch, hub, workstation, etc.) must

be less than 100 meters (328 ft.) long.

For the single mode fiber optic segment, use 9/125 µm single mode

fiber cable. You can connect two devices over a distance of 30

Kilometers.

For the multimode fiber optic segment use 50 or 62.5/125 um

multimode fiber cable. You can connect two devices up to a 2-kilometer

(6,562 ft.) distance.

DC IN

Problem Solving

Check the DIP-switch configuration. It must be set in the same

operational mode as the corresponding link.

Select the proper UTP/fiber optic cable to construct your network. The

single-mode media converter must use single-mode fiber optic cable.

Please check that you are using the right cable.

Optical Fiber Specifications

The following table shows the optical Fiber Specification

Module Name

Wavelength

(nm)

Avg. Launch

Power (dB)

Avg. Sensitivity

(dB)

ComNet CWFE2SCM2

1310 (nm)

-18 (dB)

-30 (dB)

ComNet CWFE2SCS2

1310 (nm)

-6 (dB)

-34 (dB)

Module Name

Avg. Power

Loss Budget

(dBm)

Max. FDX Fiber

Distance (Km)

Fiber Size (um)

ComNet CWFE2SCM2

12 (dBm)

2 (Km)

62.5/125

50/125

ComNet CWFE2SCS2

28 (dBm)

30(Km)

9/125

Optical Specifications of Transceivers

Transmitter (Output Center Wavelength): 1261~1360 nm

Receiver (Wavelength of Operation): 1100~1600 nm

Optical Transmit Power: Min. –15 dBm, Max. –7 dBm

1310 nm

Multimode

Single Mode

Sensitivity: Min. ---, Max. –34 dBm

Autres manuels pour CWFE2SC2

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Comnet Convertisseur de média

Comnet

Comnet FVT1D11 Manuel utilisateur

Comnet

Comnet CNFE2MCPOE Manuel utilisateur

Comnet

Comnet CWGE2SFP Manuel utilisateur

Comnet

Comnet RLMCSFP Series Manuel utilisateur

Comnet

Comnet ValueLine FVT812 Manuel utilisateur

Comnet

Comnet CWGE2SCS2 Guide de démarrage rapide

Comnet

Comnet CNMC2+1SFP Manuel utilisateur

Comnet

Comnet FVT10D2I1C4E Manuel utilisateur

Comnet

Comnet CWFE1005POEMHO-M Manuel utilisateur

Comnet

Comnet CNMC SFP Series Manuel utilisateur

Comnet

Comnet CNFE1003POEM/M Manuel utilisateur

Comnet

Comnet CNFE2MC Manuel utilisateur

Comnet

Comnet CWFE2SCM2 Manuel utilisateur

Comnet

Comnet CWFE2SC2 Manuel utilisateur

Comnet

Comnet CWFE1003POEM/M Manuel utilisateur

Comnet

Comnet CNFE2MCPOE Manuel du propriétaire

Comnet

Comnet CNGEMC4+2/M Manuel utilisateur

Comnet

Comnet FVT40D2I1C4E Manuel utilisateur

Comnet

Comnet CNFE100-A Manuel utilisateur

Comnet

Comnet CNGE2MCPOEM Manuel utilisateur

Comnet

Comnet CNFE2MC Manuel utilisateur

Comnet

Comnet CNFE2MC2C/M Manuel utilisateur

Manuels Convertisseur de média populaires d'autres marques

SoundTraxx

SoundTraxx Blunami BLU-2200 Manuel utilisateur

SPROLINK

SPROLINK VA1 Manuel utilisateur

Acclaim Lighting

Acclaim Lighting DDC-1-AC Manuel utilisateur

Nikon

Nikon AF-S TC-20E III Manuel utilisateur

Axis

Axis AXIS Q7406 Manuel utilisateur

Omega

Omega TAC80B-J Manuel utilisateur

Zoom

Zoom Thunderbolt TAC-2R Manuel utilisateur

OST

OST iConverter 10/100M Manuel utilisateur

Vertiv

Vertiv Netsure Manuel utilisateur

birddog

birddog MINI Manuel utilisateur

Roland

Roland GI-10 Manuel utilisateur

Wallenstein

Wallenstein WX310 Manuel utilisateur

Pace

Pace MSS 200-1 Manuel utilisateur

Solar Converters

Solar Converters EQ 12/24-50 Manuel utilisateur

CYP

CYP EL-7400V Manuel utilisateur

TIE

TIE MIDI 1i1o Manuel utilisateur

DCS

DCS Vivaldi Upsampler Manuel utilisateur

Westermo

Westermo MCW-211 SERIES Manuel utilisateur