Comnet CWFE2SC2 Manuel utilisateur

INSTALLATION AND OPERATION MANUAL

CWFE2SC(M,S)2

Commercial Grade 10/100 Mbps Ethernet

2 Port Electrical-to-Optical Media Converter

The ComNet ValueLine CWFE2SC(M,S)2 Ethernet 2-port media converters are designed

to transmit and receive a single channel of 10/100 Mbps data over multimode or single

mode optical fiber. The electrical interface will Auto-Negotiate to a 10 Mbps, or 100 Mbps

Ethernet rate without any adjustments. The optical interface operates at a 100 Mbps

Ethernet rate. These media converters are commercial grade for light industrial use.

Rev. 11.17.17

QSG_CWFE2SC(M,S)2 Rev. 11.17.17 PAGE 2

INSTRUCTION MANUAL CWFE2SC(M,S)2

TECH SUPPORT: 1.888.678.9427

Contents

Introduction 3

Features 3

Hardware Description 4

Front Panel 4

Ports 4

LED Indicators 5

DIP-switch 6

Rear Panel 7

Cabling 7

Connections 7

Problem Solving 8

Optical Fiber Specifications 8

Optical Specifications of Transceivers 8

Technical Specifications 9

QSG_CWFE2SC(M,S)2 Rev. 11.17.17 PAGE 3

INSTRUCTION MANUAL CWFE2SC(M,S)2

TECH SUPPORT: 1.888.678.9427

Introduction

The ComNet CWFE2SC(M,S)2 is a cost-effective solution for converting 10/100Base-TX electrical

to and 100Base-FX fiber optic cable, It allows you to extend the distance of your 100Base-FX

network up to 3 kilometers for multi-mode fiber or up to 30 kilometers for single-mode fiber.

The ComNet CWFE2SC(M,S)2 gives you the option of choosing between the most popular fiber

cabling connectors: SC/multi-mode fiber connector and SC single-mode fiber connectors. The

CWFE2SC(M,S)2 module provides you with one fiber port for your fiber optic cable and one

Ethernet RJ45 port (Auto MDI/MDIX) for your 100Base-TX copper cable connection. There are 4

DIP- switches to set the operation mode for UTP, Fiber ports and link loss forwarding function.

Features

ComNet CWFE2SC(M)(S)2

»Complies with IEEE 802.3, 802.3u, and 802.3x standards.

»Converts between UTP cabling and fiber-optic cable.

»One RJ-45 connector, Auto-MDI/MDIX for UTP port.

»Supports 10/100 Mbps Auto-negotiation for UTP port.

»Fiber optic cabling connectivity up to 30Km.

»Store-and-forward switching architecture.

»Two SC fiber connectors for 100Base-FX optical transmission.

»4 DIP-switches to set the operation mode and Link- Lost-Forwarding function.

»6 LEDs for per port: 100, Link, Activity, Full, Collision, and per unit Power.

»External DC power adapter 5-12 VDC.

»FCC Class A, CE Mark certification

Package Contents

»Stand-alone converter module package contains following items.

»Media Converter

»AC-DC Power Adapter

»User Guide

Compare the contents of your converter module with the checklist above. If any item is damaged

or missing, please contact your local dealer for service.

QSG_CWFE2SC(M,S)2 Rev. 11.17.17 PAGE 4

INSTRUCTION MANUAL CWFE2SC(M,S)2

TECH SUPPORT: 1.888.678.9427

Hardware Description

Unit dimension (L × W × H) is: 119 × 85 × 26 mm

Front Panel

The Front Panel of the ComNet CWFE2SC(M,S)2 consists of one RJ-45 Port (Auto MDI/MDIX),

6 LED Indicators (UTP 100, LK/ACT, FDX/COL, Fiber LK/ACT, FDX/COL and PWR) and one fiber

100Base-FX Port.

Fast Fiber Converter Module - SC Model

Ports

RJ-45 Port (Auto MDI/MDIX): the Ethernet RJ-45 will auto-sense for 10Base-T or 100Base-TX

connections. Auto MDI/MDIX means that you can connect to another switch or workstation

without changing non-crossover or crossover cabling.

Fiber Port: This port is for 100 Base-FX connections.

QSG_CWFE2SC(M,S)2 Rev. 11.17.17 PAGE 5

INSTRUCTION MANUAL CWFE2SC(M,S)2

TECH SUPPORT: 1.888.678.9427

LED Indicators

There are 6 diagnostic LEDs located on the Front panel of the media converter. They provide real-

time information of system and optional status. The indicator includes Power, UTP 100, LK/ACT,

FDX/COL, Fiber LK/ACT, FDX/COL. The following table provides description of the LED status and

their meanings.

LED Color Status Description

PWR Green On Power On

100 Green On 100 Mbps UTP Speed

Off 10 Mbps UTP Speed

LK/ACT (UTP) Green On The unit is linking with its link partner.

Green Blinking The unit is transmitting or receiving packets from UTP devices.

Off No device attached

LK/ACT (Fiber) Green On The unit is linking with its link partner.

Green Blinking The unit is transmitting or receiving packets from FX devices.

Off No device attached

FDX/COL (UTP) Orange On The UTP port is operating in full-duplex mode.

Orange Blinking Collision of packets is occurring in the port.

Off Half-duplex mode or no device attached.

FDX/COL (Fiber) Orange On The fiber port is operating in full-duplex mode.

Orange Blinking Collision of packets is occurring in the port.

Off Half-duplex mode or no device attached.

QSG_CWFE2SC(M,S)2 Rev. 11.17.17 PAGE 6

INSTRUCTION MANUAL CWFE2SC(M,S)2

TECH SUPPORT: 1.888.678.9427

DIP-switch

The DIP-switch is used to configure operation mode for LLF (Link Lost Forwarding) and operation

mode for UTP/Fiber port. The default value of DIP switch is OFF.

SW No Status Description

1ON UTP 100 Mbps Full Duplex Mode

OFF UTP Auto-Negotiate

2ON Fiber in Half Duplex

OFF Fiber in Full Duplex

3ON LLF Enable

OFF LLF Disable

4ON Pure Converter mode

OFF Switch Converter mode

Link Lost Forwarding (DIP-Switch 3): When LLF is enabled, it allows UTP link failures to be reported

to the fiber side and also allows a fiber link failure to be reported to the UTP side. Therefore, a link

loss forward feature is provided in both UTP and fiber side.

Pure Converter mode (DIP-Switch 4): When the pure converter mode is enabled (on), it operates

with minimal latency. The transmission flow does not wait until the entire frame is ready, but

instead it forwards the received data immediately after the data has been received. The UTP port

should be forced at 100M in this application. When DIP-Switch is in Switch Converter mode (off),

the converter function is same as Switch Hub.

Note: Do not change the DIP-switch setting when UTP or fiber port is transmitting or receiving

data. It may cause some data errors. If you change the DIP-switch setting, please power off

the converter and power it on again to make the setting effective.

QSG_CWFE2SC(M,S)2 Rev. 11.17.17 PAGE 7

INSTRUCTION MANUAL CWFE2SC(M,S)2

TECH SUPPORT: 1.888.678.9427

Rear Panel

The rear panel contains a power socket, which accepts 5-12 VDC @ 2.7 W.

Connect the included Power Supply to the rear panel DC IN jack.

Plug the AC input of the Power Supply to a commercial power source.

DC IN

Fast Fiber Converter Module - Rear Panel

Cabling

»For the Twisted-pair segment unshielded twisted pair (UTP) or shielded twisted pair (STP)

cabling can be used. The cable must comply with the IEEE 802.3u 100Base TX standard for

Category 5. The cable between the converter and the link partner (switch, hub, workstation,

etc.) must be less than 100 meters (328 feet) long.

»For the single mode fiber optic segment, use 9/125 μm single mode fiber cable. You can

connect two devices over a distance of 30 kilometers.

»For the multimode fiber optic segment use 50 or 62.5/125 µm multimode fiber cable. You can

connect two devices up to a 3 kilometer (2 mile) distance.

Connections

CAT5e CAT5e

2 Multimode

or Single Mode

Optical Fibers

Ethernet

Device

CWFE2SC CWFE2SC

Ethernet

Device

POWER

SUPPLY

POWER

SUPPLY

QSG_CWFE2SC(M,S)2 Rev. 11.17.17 PAGE 8

INSTRUCTION MANUAL CWFE2SC(M,S)2

TECH SUPPORT: 1.888.678.9427

Problem Solving

»Check the DIP-switch configuration. It must be set in the same operational mode as the

corresponding link.

»Select the proper UTP/fiber optic cable to construct your network. The single-mode media

converter must use single-mode fiber optic cable. Please check that you are using the right

cable.

Optical Fiber Specifications

The following table shows the optical Fiber Specification

Module Name Wavelength (nm) Avg. Launch Power (dB) Avg. Sensitivity (dB)

CWFE2SCM2 1310 nm -20 dB -30 dB

CWFE2SCS2 1310 nm -15 dB -30 dB

Module Name Avg. Power Loss Budget (dBm) Max. FDX Fiber Distance (Km) Fiber Size (um)

CWFE2SCM2 10 dBm 3 km 62.5/125

50/125

CWFE2SCS2 15 dBm 30 km 9/125

Optical Specifications of Transceivers

1310 nm

Multimode

Single Mode

Transmitter (Output Center Wavelength): 1261~1360 nm

Receiver (Wavelength of Operation): 1100~1600 nm

QSG_CWFE2SC(M,S)2 Rev. 11.17.17 PAGE 9

INSTRUCTION MANUAL CWFE2SC(M,S)2

TECH SUPPORT: 1.888.678.9427

Technical Specifications

ComNet CWFE2SC(M,S)2 technical specifications are as follows:

Standard IEEE802.3 10BASE-T

IEEE802.3u 100BASE-TX/100BASE-FX

IEEE802.3x Flow Control and Back pressure

Connector Fiber: Duplex SC

RJ45 Socket: CAT-3/5 (10/100Mbps) Twisted Pair cable

Auto MDI/MDI-X and Auto-Negotiation Function Support

Switch architecture Store and Forward

Fiber parameters Fiber Core: Multi-Mode (62.5/125 μm, 50/125 μm)

Single-Mode (9/125 μm)

Wavelength: 1310 nm Multimode & Single-mode

Fiber Distance: Multi-Mode Fiber 3 km

Single-Mode Fiber 30 km

Transparent packet 64 to 1518 Bytes for Non-VLAN Ethernet packet

Link Lost Forward UTP to Fiber: If UTP port link is down, the converter will force the fiber to link

down.

Fiber to UTP: If Fiber port link is down, the media converter will force UTP port to

link down.

DIP Switch DIP Switch 1: UTP Auto-Negotiate / 100Mbps Full Duplex mode

DIP Switch 2: Fiber Full/Half Duplex

DIP Switch 3: LLF (Link Lose Forwarding) Disable/Enable

DIP Switch 4: Switch Converter / Pure converter mode

LED Module: Power, TX (100Mbps, LK/Act, FDX/COL) Fiber (LK/Act, FDX/COL)

Power Stand-alone (external adapter): 5-12 VDC @ 2.7 W

Dimension Module: 119 × 85 × 26 mm

EMI & safety FCC Class A, CE

3 CORPORATE DRIVE | DANBURY, CT 06810 | USA

T: 203.796.5300 | F: 203.796.5303 | TECH SUPPORT: 1.888.678.9427 | INFO@COMNET.NET

8 TURNBERRY PARK ROAD | GILDERSOME | MORLEY | LEEDS, UK LS27 7LE

T: +44 (0)113 307 6400 | F: +44 (0)113 253 7462 | INFO-EUROPE@COMNET.NET

MECHANICAL INSTALLATION INSTRUCTIONS

ComNet Customer Service

Customer Care is ComNet Technology’s global service center, where our professional staff is

ready to answer your questions at any time.

Email ComNet Global Service Center: customercare@comnet.net

Autres manuels pour CWFE2SC2

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Comnet Convertisseur de média

Comnet

Comnet FVT40D2I1C4E Manuel utilisateur

Comnet

Comnet CNFE2MC2C/M Manuel utilisateur

Comnet

Comnet RLMCSFP Series Manuel utilisateur

Comnet

Comnet CNFE2MC Manuel utilisateur

Comnet

Comnet CNGEMC4+2/M Manuel utilisateur

Comnet

Comnet CWGE2SCS2 Guide de démarrage rapide

Comnet

Comnet CNMC SFP Series Manuel utilisateur

Comnet

Comnet CNFE2MCPOE Manuel du propriétaire

Comnet

Comnet CWFE1005POEMHO-M Manuel utilisateur

Comnet

Comnet CWFE2SC2 Manuel utilisateur

Comnet

Comnet CNFE100-A Manuel utilisateur

Comnet

Comnet ValueLine FVT812 Manuel utilisateur

Comnet

Comnet CNGE2MCPOEM Manuel utilisateur

Comnet

Comnet CNMC2+1SFP Manuel utilisateur

Comnet

Comnet CWFE1003POEM/M Manuel utilisateur

Comnet

Comnet CWFE2SCM2 Manuel utilisateur

Comnet

Comnet CNFE2MCPOE Manuel utilisateur

Comnet

Comnet CWGE2SFP Manuel utilisateur

Comnet

Comnet FVT10D2I1C4E Manuel utilisateur

Comnet

Comnet FVT1D11 Manuel utilisateur

Comnet

Comnet CNFE2MC Manuel utilisateur

Comnet

Comnet CNFE1003POEM/M Manuel utilisateur

Manuels Convertisseur de média populaires d'autres marques

SoundTraxx

SoundTraxx Blunami BLU-2200 Manuel utilisateur

SPROLINK

SPROLINK VA1 Manuel utilisateur

Acclaim Lighting

Acclaim Lighting DDC-1-AC Manuel utilisateur

Nikon

Nikon AF-S TC-20E III Manuel utilisateur

Axis

Axis AXIS Q7406 Manuel utilisateur

Omega

Omega TAC80B-J Manuel utilisateur

Zoom

Zoom Thunderbolt TAC-2R Manuel utilisateur

OST

OST iConverter 10/100M Manuel utilisateur

Vertiv

Vertiv Netsure Manuel utilisateur

birddog

birddog MINI Manuel utilisateur

Roland

Roland GI-10 Manuel utilisateur

Wallenstein

Wallenstein WX310 Manuel utilisateur

Pace

Pace MSS 200-1 Manuel utilisateur

Solar Converters

Solar Converters EQ 12/24-50 Manuel utilisateur

CYP

CYP EL-7400V Manuel utilisateur

TIE

TIE MIDI 1i1o Manuel utilisateur

DCS

DCS Vivaldi Upsampler Manuel utilisateur

Westermo

Westermo MCW-211 SERIES Manuel utilisateur