Community MX-Y8 Manuel utilisateur

MX-Y8 / MX-Y10 Yoke

M-Class MX8 and MX10 Mounting Yokes

Standard Yoke-Type Mounting Brackets for Community

M-Class MX8 and MX10 Monitor Systems

The MX-Y8 and MX-Y10 yoke brackets are designed to flush mount the M-Class

series MX8 and MX10 loudspeakers in either a vertical or horizontal orientation tightly

against a wall or ceiling. Corner mounting is also possible when the yoke is mounted

vertically and the loudspeaker horizontally with the bottom and rear of the enclosure

against adjacent walls. Such mounting is further aided by the convenient location of

the input panel on the bottom rear of the loudspeaker enclosure.

The yokes are manufactured of steel, covered with a durable powder-coat finish, and are

available in either black or white to match the color of the loudspeaker enclosure. They

are engineered to provide a high margin of safety when supporting the correct M-Class

loudspeaker. Use the MX-Y8 yoke for the MX8 monitor and MX-Y10 yoke for the MX10

monitor.

The yoke bracket is provided with the hardware required to attach it to the loudspeaker enclosure. No additional

hardware is provided to attach the yoke bracket to the mounting surface. Such hardware must be supplied by the

installer and should be sized and rated for the weight load of the loudspeaker, keeping in mind that additional torque

load may occur when focusing the loudspeaker within the yoke assembly. The installer is solely responsible for

determining if the mounting surface is capable of safely supporting the weight load of the loudspeaker, and for

selecting appropriate hardware to install it.

The loudspeaker input panel is located

on the rear of the enclosure.

Wall, ceiling and corner mounting of the M-Class MX8 or MX10

monitor is possible using the MX-Y8 and MX-Y10 yokes.

Parts List:

Mounting Yoke (1)

Rubber Washer (2)

M10 x 30 mm Hex Bolt (2)

10mm Flat Washer (2)

10mm Lock Washer (2)

The installer must supply all other hardware

for the installation.

Part No. Description

MX-Y8B Yoke Bracket for M-Class MX8-B (black)

MX-Y8W Yoke Bracket for M-Class MX8-W (white)

MX-Y10B Yoke Bracket for M-Class MX10-B (black)

MX-Y10W Yoke Bracket for M-Class MX10-W (white)

Danger: All rigging points on each enclosure must be fitted with either optional mounting hardware or they

must remain sealed with the flat-head Allen screws that come installed in the enclosure. The flat-head

Allen screws pass through the plywood panels and fasten to internal steel rigging brackets, thereby

providing structural integrity. Without these Allen screws, the structural integrity of the plywood enclosure would

rely solely on the adhesion of the glue joints, which over time could deteriorate. Therefore, all rigging fittings

must have fasteners in place so that the enclosure may be safely mounted. Additionally, if the rigging fittings

are not sealed, air leaks will occur in the enclosure that will compromise the low frequency performance with

distortion and reduced output.

Assembly Instructions

1. Before installing the loudspeaker in the yoke, the yoke should first be attached to the mounting surface. No

hardware is provided for this purpose. Such hardware must be supplied by the installer, and should be rated for

the weight load of the enclosure. The installer is solely responsible for determining if the hardware used to

mount the yoke is adequately sized and rated, and if the structure it is attached to is capable of safely

supporting the weight load of the enclosure.

2. Installing the loudspeaker in the yoke is straightforward. First, remove two of the flat-head Allen screws that

come installed in the loudspeaker, one on each side of the enclosure.

3. Position the loudspeaker within the yoke, making sure to leave enough clearance for the speaker wire and

connector.

4. Next, fit each of the two M10 x 30mm bolts with a lock washer and a flat washer. Place the two large rubber

washers between the yoke and the loudspeaker, then pass each bolt through the yoke bracket and the rubber

washer into the loudspeaker’s rigging fitting. Tighten the fasteners until snug. After focusing the loudspeaker in

the desired position, the bolts should be tightened to a torque of approximately 12 to 15 foot-pounds, using a

torque wrench. Do not overtighten.

Assembly Diagram

MX-Y8 Yoke Diagram

MX-Y10 Yoke Diagram

Caution: Installation of loudspeakers should

only be performed by trained and qualified

personnel. It is strongly recommended that a

licensed and certified professional structural

engineer approve the mounting design.

Community Professional Loudspeakers

333 East Fifth Street, Chester, PA 19013 USA

Phone (610) 876-3400 | Fax (610) 874-0190

www.communitypro.com

16MAY2016

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Community Intervenants

Community

Community Wet II Fiche technique

Community

Community ENTASYS Manuel utilisateur

Community

Community I/05 Manuel utilisateur

Community

Community C4LP Manuel utilisateur

Community

Community CP6 Manuel utilisateur

Community

Community Distributed Design DA6 Manuel utilisateur

Community

Community MVP25 Manuel utilisateur

Community

Community R.5-MAX Manuel utilisateur

Community

Community C SERIES CP6 Manuel utilisateur

Community

Community MVP28 Manuel utilisateur

Community

Community R SERIES Mode d'emploi

Community

Community R.15COAX Manuel utilisateur

Community

Community Distributed Design D4LP Manuel du propriétaire

Community

Community R-VTY15 Manuel

Community

Community WET Series II Fiche technique

Community

Community WX-1226 Manuel utilisateur

Community

Community Veris Series Manuel utilisateur

Community

Community R SERIES Manuel utilisateur

Community

Community MX8 Manuel utilisateur

Community

Community ENTASYS Guide de l'utilisateur

Community

Community Point Source 600 Guide de démarrage rapide

Community

Community MVP37 Manuel utilisateur

Community

Community Cloud1299 Manuel utilisateur

Community

Community MX8 Manuel utilisateur

Manuels Intervenants populaires d'autres marques

argon audio

argon audio IE20 Manuel utilisateur

Denon

Denon SC-N7 Manuel utilisateur

Gemline

Gemline Ace 3952 Manuel utilisateur

Focal

Focal ON WALL 300 Mode d’emploi

HEADRUSH

HEADRUSH Maximus HRSP 5024 Manuel utilisateur

SoundLogic

SoundLogic BCCS-6/6395 Manuel utilisateur

Peavey

Peavey DTH 218 Manuel utilisateur

Avantree

Avantree Pluto Air Manuel utilisateur

Morel

Morel Integra Series INTEGRA OVATION 4 Manuel utilisateur

Oppo

Oppo SONICA Manuel utilisateur

Bose

Bose SoundLink Wireless Music System Manuel utilisateur

Rocksteady

Rocksteady Stadium Manuel utilisateur

Bowers & Wilkins

Bowers & Wilkins 4 Manuel utilisateur

Sonance

Sonance SONOS OUTDOOR Series Manuel utilisateur

Electro-Voice

Electro-Voice EVID FM4.2 Manuel utilisateur

Pioneer

Pioneer XW-HTD630 Manuel utilisateur

Onn

Onn BWA16AA002 Manuel utilisateur

HP GL313AA - USB Speakers PC Multimedia Manuel utilisateur