Coloronix SS2 Manuel utilisateur

SS2

SS2 SS2

SS2 -

DIRECT

DIRECT DIRECT

DIRECT

POWER

POWERPOWER

POWER

LIGHTING

LIGHTING LIGHTING

LIGHTING

MANUAL

MANUAL MANUAL

MANUAL

Coloronix, Inc.

5461 West Jefferson Boulevard

Los Angeles, California 9 16

(323) 677-4242

http://www.rgbw.com

Page 2 of 13 - Coloronix SS2 Direct Power Lighting Manual V.2. .1

Coloronix, Inc.

According to copyright laws, this manual may not be copied—partially, or wholly—

without the written consent of Coloronix, Inc.

Despite full effort to avoid any clerical or printing inaccuracies, Coloronix, inc. accepts

no responsibility for any such inaccuracies to be found in this manual.

Coloronix, Inc.

5461 West Jefferson Boulevard

Los Angeles, California 9 16

Tech Support: (9 9) RGBW-555

http://www.rgbw.com

Coloronix and the Coloronix logo are brands of Coloronix, Inc.

Any non-Coloronix brands or products found in this manual are not endorsed, branded,

or recommended for use by Coloronix, Inc.; rather, they are only references for

informational purposes. Coloronix has no responsibility for these products in regards

to either performance or use.

Page 3 of 13 - Coloronix SS2 Direct Power Lighting Manual V.2. .1

Contents

ContentsContents

Contents

Summary 4

Summary 4Summary 4

Summary 4

Introduction 4

Scope 4

Who is this manual intended for? 4

Additional Supplies 4

Sa ety 5

Sa ety 5Sa ety 5

Sa ety 5

Hazard Icon Key 5

Speci ications 5

Speci ications 5Speci ications 5

Speci ications 5

Planning or Installation 6

Planning or Installation 6 Planning or Installation 6

Planning or Installation 6

Unpacking 6

Preparation 6

Points to Consider About Data 6

Quick Step-by-Step Instructions 6

Setting Color Mode 7

Setting Color Mode 7Setting Color Mode 7

Setting Color Mode 7-

-8

DMX Mode 7

Pre-Programmed Mode 8

Mount

MountMount

Mounting and Alignment o Fixture 9

ing and Alignment o Fixture 9ing and Alignment o Fixture 9

ing and Alignment o Fixture 9-

-10

1010

Electrical Connection 9

Data Connection 1

Maintenance 1

Maintenance 1Maintenance 1

Maintenance 11

Replacing a Failed Fixture 11

Troubleshooting Guide 12

Troubleshooting Guide 12Troubleshooting Guide 12

Troubleshooting Guide 12

Warranty In ormation 13

Warranty In ormation 13Warranty In ormation 13

Warranty In ormation 13

Page 4 of 13 - Coloronix SS2 Direct Power Lighting Manual V.2. .1

Summary

SummarySummary

Summary

Introduction

RGBW Color Changing Adjustable Flood Lights are active, top-of-the-line color changing

fixtures. They draw on solid-state elements in order to produce highlights and washes

in architectural spaces.

More specifically, “RGBW” is an acronym for “Red, Green, Blue, and White”. RGBW

LED color mixing luminaires have the potential to produce 4.3 billion colors, and 16.7

million white light tones.

When installed and operated according to this manual, these downlights will operate

safely and dependably for their rated lifespan.

These luminaries require a USITT DMX 512 control signal on four consecutive

channels total. The unit includes a DATA OUT output for connection to additional units

or other DMX512 devices.

The flood lights are UL 1598 wet location rated for use in indoor or outdoor

environments.

Scope

The purpose of this manual is to properly install and use color-changing flood lights at

peak performance

This manual must be complimented by additional references, consultation from

qualified professional(s), and observance of state and local codes and regulations. This

rule applies to any interior structure, exterior structure, or environment.

Therefore, it is important to:

“please read and comply with all instructions and

warnings in this manual when installing or using this product.”

Who Is This Manual Intended for?

This manual is intended for electrical contractors, electrical engineers, and licensed

electricians.

Additional Supplies

DMX512 compatible controller (optional)

DMX extension (optional)

DMX feed connector

4x4 inch electrical junction box rated for the application (optional)

Controller (DMX512 compatible)

Proper mounting bolts, washers and lock washers to secure the fixture to the mounting

surface.

Page 5 of 13 - Coloronix SS2 Direct Power Lighting Manual V.2. .1

Sa ety

Sa etySa ety

Sa ety

Hazard Icon Key:

The “ DANGER” icon means avoiding

pending

danger will result in serious injury, or death.

The “ WARNING” icon means avoiding this warning may result may in serious injury, or death.

The “ CAUTION” icon means not exercising caution here may result in minor to moderate injury, or property damage.

The precautions are:

DANGER: Not turning off the main power before wiring, installing, connecting, or disconnecting this product may result in

serious injury, or death.

WARNING: Not following NEC codes, local codes, or consulting a certified professional may result in property damage,

serious injury, or death.

WARNING: Not following instructions, or safety labels may result in property damage, or serious injury.

WARNING: Modifying, servicing, or ignoring these safety indications may void the warranty.

WARNING: Inspect product before use. DO NOT use if damaged.

WARNING: Install safety cables per local and structural engineer’s code.

CAUTION: Hot swapping, not turning off fixtures before connection or disconnection, will void the warranty, and damage

property.

CAUTION: Do not go beyond the specified voltage, input current, maximum number of fixtures, or run length.

CAUTION: Do not use sharp tools near the reflector or lens.

CAUTION: Do not look directly into beam, with or without optical instruments.

Note: Instructions and warning referenced in this installation guide are not

necessarily all inclusive, all conceivable, or all relevant to all applications as

Coloronix cannot anticipate all conceivable or unique situations.

Speci ications

Speci icationsSpeci ications

Speci ications

Power Input: Direct 12 -24 VAC 5 Hz/6 Hz

Power Consumption: 52W for “-6” version, 79W for “-9” version

L70 Life: 35, Hours.

Temperature Rating: 14°F - 1 4°F Ambient.

LED Die Colors: Red (62 -635nm)

Green (52 -535nm)

Blue (45 -465nm)

Neutral White (5 k)

Safety: Complies to UL1598 and ANSI/UL 875 .

Page 6 of 13 - Coloronix SS2 Direct Power Lighting Manual V.2. .1

Planning or I

Planning or IPlanning or I

Planning or Installation

nstallation nstallation

nstallation

Unpacking

The data enabler and trim are shipped assembled with no additional assembly needed.

Housing and trim are shipped in two different boxes.

Any optional accessories are included in the package. Use the packing list located on the

outside of the box to ensure all accessories are included.

Survey the unit to make sure the data enabler/trim are all intact—not cracked or

damaged. Any damages to the package or its contents are of the buyer’s responsibility;

please follow protocol for filing damage claims. Please recycle or appropriately discard of

any packing materials.

Preparation

Before Installation, Coloronix suggests:

• Consulting the provided submittal drawings to recognize layouts of luminaries,

power supplies, and wiring layouts.

• Drawing out a layout plan consisting of locations of luminaries and wiring.

• Record DMX addresses on a mapping grid for easy reference and addressing

(where applicable).

• An electrical inspector reviews all wiring plans.

Points to Consider About Data

•

Max power links is 9 per power feed

• AC Power and DATA cables may NOT run in the same conduit or within one

foot due to possible induced errors.

• 32 DMX DATA links max per run

Quick Step-by-Step Instructions

To successfully install RGBW Recessed Lighting, the steps are:

1. Mounting and alignment of fixture

AC power connections

DMX connections

Ready to go.

Page 7 of 13 - Coloronix SS2 Direct Power Lighting Manual V.2. .1

Setting Color Mode

Setting Color Mode Setting Color Mode

Setting Color Mode

DMX Mode

For installations requiring DMX control, set the

personalized DMX address using the address table (Below)

for LCD menu settings. See figure.

Note: Up to 128 unique 4-channel addresses can be set

per DMX universe.

1. Press the “MODE”

，

enter the DMX mode “d.×××”.

2. Press the “UP” or “DOWN”

，

set up the DMX address value d. 1-d.512

3. Press the “SETUP”, enter the DMX working mode: X-ch

4. Press the “UP” or “DOWN”

，

set up the DMX working mode (See below)

DMX Working Mode 1: 1 CHANNEL (For static color control, 1 channel per fixture)

CH1

No. DMX Value Function

1 No use

2 1-22 Red

3 23-45 Green

4 46-68 Blue

5 69-91 Cyan

6 92-114 Yellow

7 115-137 Orange

8 138-16 Pink

9 161-183 Purple

1 184-2 6 Dark Blue

11 2 7-229 Light Green

12 23 -252 White

13 253-255 Warm White

DMX Working Mode 2: 4 CHANNEL

(For individual color dimming control)

Channel Value Function

CH1 -255 Red

CH2 -255 Green

CH3 -255 Blue

CH4 -255 Cool White

DMX Working Mode 3: 5 CHANNEL

(For individual color control and master

dimmer function)

Channel Value Function

CH1 -255 Master dimmer

CH2 -255 Red

CH3 -255 Green

CH4 -255 Blue

CH5 -255 White

Lock Function:

If MENU is IDLE for 2 seconds, MENU will lock. Hold “MODE” and “DOWN” button to

release lock.

Page 8 of 13 - Coloronix SS2 Direct Power Lighting Manual V.2. .1

Pre-Programmed Mode (Static Color)

1. Press “MODE”

，

enter the mode “Prxx”

2. Enter Pr. 1

3. Press “SETUP” and toggle between static color to achieve desired show

No. Color

1 Red

2 Orange

3 Green

4 Green/Blue

5 Blue

6 Purple

7 RGB

8 White

9 Bright White

1 Pink

11 Light Green

12 Light Blue

*Consult factory for custom colors in the RGBW spectrum.

Pre-Programmed Mode (Show Mode)

1. Same as above

2. Toggle between Programs 2-11 to achieve desired show

No. Show

2 Different shades of:

Red, green, blue, gray, yellow, hot pink, light pink, turquoise, green-blue, light

blue, gray, gray, turquoise, pink (slow fade to and from black between

colors)

3 RGBW (fade to and from black between colors)

4 RGBW (quick jump between colors)

5 RGBW (strobe effect)

6 RGBW (blend between colors slow)

7 RGBW (blend between colors fast)

8 Red (long duration on, then quick jump off and on)

9 Green (long duration on, then quick jump off and on)

1 Blue (long duration on, then quick jump off and on)

11 White (long duration on, then quick jump off and on)

Page 9 of 13 - Coloronix SS2 Direct Power Lighting Manual V.2. .1

Mounting and Alignment o Fixture

Mounting and Alignment o FixtureMounting and Alignment o Fixture

Mounting and Alignment o Fixture

•

Mount and secure each fixture into the designated position in accordance to the

installation plan. Ensure there is sufficient cable length between the fixture and junction

box to allow for final alignment of the fixture.

•

Secure the fixtures to a solid mounting surface using three threaded fasteners

minimum of 3/8 inch (1 mm) stainless steel complete with flat and locking washer.

•

Rotate the fixtures using the pan and tilt method into the desired position.

Electrical Connection (Hardwire)

WARNING: Do not expose bare wires outside wire nut connectors.

1. Per local or “National Electric Code”, provide electrical service to junction box

located on the housing.

a. The insulation of supply wire must be rated for at least 9 °C.

b. Junction boxes should be rated for:

i. Max. 8 No. 12 AWG Circuit Conductors

ii. Also suitable for at least 9 °C

2. Remove cover of junction box.

3. Remove proper round pryout, and then connect junction box with (not included)

proper connector.

4. Using properly sized wire nuts, connect lead wires of junction box (line, neutral,

and ground) to supply lead wires in the fixture.

a. WARNING: Do not leave bare conductors outside wire nut connectors.

5. Connect green (from electrical service) to the supply side to the green wire in

the junction box. Connect black-to-brown, and white-to-blue.

a. Any excess wiring and connectors should be put in the junction box.

Then, replace the cover.

NOTE: Supply lead wires should not be connected to a dimmer of any sort.

Maximum power connection should not exceed 9 units at 12 V.

Page 1 of 13 - Coloronix SS2 Direct Power Lighting Manual V.2. .1

Data Connection

Note: Inline DMX amplifier required if run length exceeds: 125 feet between fixtures (others)

Note: Maximum run length from DMX controller to last fixture: 1 feet.

Note: DMX must be continuous from controller to last fixture in a run. A splitter is needed if

signal is split.

Please follow below if provided data cables will not be used

Note: Fixtures on a serial data link must be daisy chained in one single line. To comply with

the EIA 485 standard, no more than 32 fixtures should be connected on one data link.

Connecting more than 32 fixtures on one serial data link without the use of a DMX

optically isolated splitter may result in deterioration of the digital DMX signal.

Maximum recommended serial data link distance: 5 m (164 ft)

Maximum recommended number of fixtures on a serial data link: 32

DMX Data Cable

specifications for EIA RS-485 applications. Standard microphone cables cannot transmit DMX data

reliably over long distances. The cable must have the following characteristics:

Type: shielded, 2-conductor twisted pair

Maximum capacitance between conductors:

3 pF/ft

Maximum capacitance between conductor and shield:

55 pF/ft

Maximum resistance: 2 ohms/1 ft

Normal impendance: 1

14 ohms

Note: To comply with all local codes and jurisdiction, qualified communications technicians must do

communications wiring.

Note: Communication cables and AC power lines must not be run in the same conduit.

A. Route Data Cables in series between fixture and any communications accessories using DATA

IN and DATA OUT.

B. In order that they may be easily accessed once construction is complete, secure data cables in

the immediate proximity of the fixtures.

Note: To avoid signal transmission problems and interference, it is always advisable to connect to a

DMX signal terminator.

Table des matières

Autres manuels Coloronix Luminaire

Coloronix

Coloronix RGBW Pendant Manuel utilisateur

Manuels Luminaire populaires d'autres marques

Emos

Emos CLASSIC ZY1431T Manuel utilisateur

Westinghouse

Westinghouse Outdoor Lighting Fixture Manuel utilisateur

Hedler

Hedler C 12 silent Manuel utilisateur

Blizzard Lighting

Blizzard Lighting Puck: CSI Manuel utilisateur

Energetic Lighting

Energetic Lighting ELYSL-5004 Series Manuel utilisateur

Lightmaxx

Lightmaxx Shaft 5R Manuel utilisateur

Triarch

Triarch 31083 Manuel utilisateur

Philips

Philips 32614 Series Manuel utilisateur

IKEA

IKEA TIVED Manuel utilisateur

Lightolier

Lightolier LP200 Manuel utilisateur

Chauvet Professional

Chauvet Professional ROGUE R1 BEAM WASH Manuel utilisateur

Martin

Martin MAC 250 Krypton Manuel utilisateur

Cooper Lighting

Cooper Lighting Halo L3232E Manuel utilisateur

Stageline

Stageline ODW-2410RGBW Manuel utilisateur

Light Sky

Light Sky Tornado Series Manuel utilisateur

Lightolier

Lightolier Paralyte 2424 PLA2G9LS26U Manuel utilisateur

Lightolier

Lightolier Lytespan 83ED17S Manuel utilisateur

Lightolier

Lightolier Calculite CS8226 Manuel utilisateur