CODELOCKS CL600 Manuel utilisateur
https://codelocks.zohodesk.eu/portal/en/kb/articles/cl600-code-change-guide
Codelocks Support
CL600 - Code Change Guide
Many Codes to Choose From
The CL600 range has been designed so the code can be changed on the door in seconds. The code chamber
(models 600, 610 and 620) consists of 13 buttons and a ‘C’ button which is used to re-set the code chamber after
an incorrect entry, and must always be used as the first digit of a code. Buttons may only be used ONCE in a
code. For example 1212 is NOT possible.
The CL600 ranges code or combination, can be entered in any order or sequence; eg 1234 can be 4321 or 1342 or
whatever sequence is most convenient to remember.
With 13 buttons, a total of 8,191 different codes are available, any of which can be entered in any sequence.
The total is arrived at as follows:
Note:Models 605, 615 and 625 have 12 coded buttons giving 4,095 different codes.Most people will set the
code in the range of 4 to 7 digits, and the total number of codes in this range is 5,434. The lock is supplied with a
random factory set code (see code card). At any time this can be quickly changed to a new code of your choice.
Typically codes are 4 to 7 digits long. Shorter codes are possible (1-2 digits) but are not recommended.
Passage Free Mode Models 605, 615 and 625
The above feature can be identified with a black dot on the ‘Z’ button.
To set the lock in passage free mode enter the code followed by the ‘Z’ button. The lock will now be in free
passage mode.
To put the lock back into code access only press the passage set ‘Z’ button once followed by the C button.
https://codelocks.zohodesk.eu/portal/en/kb/articles/cl600-code-change-guide
Code Change Instructions
The CL600 range offers significant advantages over other similar mechanical digital locks by allowing the code
to be changed in seconds on the door.
Note: Models 605, 615, 625 only – Before changing code press the ‘Z’ and ‘C’ button to ensure that the lock is
not in free passage mode.
1. Choose code.
2. Insert key and turn anticlockwise to stop for right hand hung doors, or clockwise to stop for left hand hung
doors. Fig 1.
3. Push the code change tool onto each button in turn, pushing in the buttons approx 2mm (3/32”) turn
anticlockwise 180°. All buttons should now be in the non code position.
4. Test that all buttons are in non code position (perform step 6 before testing buttons) then depress the lever
handle which should retract the latch. If latch cannot be retracted press ‘C’ button and repeat step 3.
5. To select a button as a code button, push code tool over button. Press in button with tool approx 2mm (3/32”)
and turn clockwise 180°. Fig 2.
6. Now turn the key clockwise for right hand hung doors, or anticlockwise for left hand hung doors retracting the
latch which will relock the code buttons. Fig 3.
7. Return the key to centre and remove.
8. Before closing door test code.
https://codelocks.zohodesk.eu/portal/en/kb/articles/cl600-code-change-guide
3.To replace cylinder, reinsert and turn 90° clockwise. Replace the cylinder cover and handle.
*If intending to use a cylinder from a different manufacturer it is advisable to confirm beforehand that the new
cylinder will fit the boss.
Notethat the CL600 uses a 6 pin screw cap cylinder.
If using a screw cap cylinder other than supplied, the tail piece from the Codelocks screw cap cylinder will need
to be fitted as follows:
4.Hold down the control pin in the end of the cylinder and unscrew the cap.
Caution!Do not insert the key in the cylinder once you have removed the screw cap!
5.Refit the tailpiece, hold down the control pin and screw the cap on fully without tightening. Ensure the control
pin projects to lock the cap.
https://codelocks.zohodesk.eu/portal/en/kb/articles/cl600-code-change-guide
Test the key operation
If the key is difficult to insert, or tight when turning, then the cap may be too tight. Loosen the cap one notch at a
time and try the key again. If the key inserts and turns OK, but is difficult to remove, then the cap may be too
loose.
Tighten up the cap one notch at a time.
Adjust the cap until the key inserts, turns and removes easily.
Dimensions
https://codelocks.zohodesk.eu/portal/en/kb/articles/cl600-code-change-guide
Features
■ On door code change in seconds.
■ Code free entry mode (models 605, 615, 625 only).
■ Inside handle always retracts the latch for exit.
■ Weather resistant.
■ Tamper resistant, with stainless steel buttons, and clutch protection if the outside handle is forced.
■ Reversible handles.
■ Easy code change as often as required.
■ Fits doors between 35mm (1 3⁄8”) and 60mm (2 3⁄8”) thick without modification.
Features - Model 620/625 Only
■ Split follower lock enables inside handle to retract latch and deadbolt simultaneously, satisfying ‘means of
escape’ requirements for exit at all times. Prevents accidental lock-ins.
■ Deadbolt thrown by key to lock out code users after work hours.
■ Key will retract the latchbolt giving access for admin functions.
■ D bl E fil li d ith 3 k A E fil li d b d
https://codelocks.zohodesk.eu/portal/en/kb/articles/cl600-code-change-guide
■ Double Euro-profile cylinder with 3 keys. Any Euro-profile cylinder may be used.
■ On multiple door installations consideration should be given to having all cylinders keyed alike, with restricted
key issue, for ease of management.
Maintenance
No maintenance of the working parts is necessary.DO NOT OIL.To maintain the finish the lock should be
cleaned regularly with a soft cloth. A silicone spray or similar should be used to provide a protective film against
grit and grime.
CC-CL600-0812
© 2019 Codelocks Ltd. All rights reserved.
Autres manuels pour CL600
1
Ce manuel convient aux modèles suivants
2
Table des matières
Autres manuels CODELOCKS Serrure de porte
CODELOCKS
CODELOCKS 4OOO ELECTRONIC Manuel utilisateur
CODELOCKS
CODELOCKS 400 mechanical Guide de l'administrateur
CODELOCKS
CODELOCKS CL160 Manuel utilisateur
CODELOCKS
CODELOCKS CL520 Manuel utilisateur
CODELOCKS
CODELOCKS CL400 Manuel utilisateur
CODELOCKS
CODELOCKS KL1200 Manuel utilisateur
CODELOCKS
CODELOCKS CL610 Manuel utilisateur
CODELOCKS
CODELOCKS CL500 Guide de l'administrateur
CODELOCKS
CODELOCKS KL1000 Classic+ Manuel utilisateur
CODELOCKS
CODELOCKS Codelock 100 Manuel utilisateur
CODELOCKS
CODELOCKS CL5510 Manuel utilisateur
CODELOCKS
CODELOCKS KitLock KL1O Manuel utilisateur
CODELOCKS
CODELOCKS CL1200 Manuel utilisateur
CODELOCKS
CODELOCKS CL5000 Manuel utilisateur
CODELOCKS
CODELOCKS CL460 Manuel utilisateur
CODELOCKS
CODELOCKS CL5510 Manuel utilisateur
CODELOCKS
CODELOCKS KL1000 Manuel utilisateur
CODELOCKS
CODELOCKS 0460 Manuel utilisateur
CODELOCKS
CODELOCKS CL400 Manuel utilisateur
CODELOCKS
CODELOCKS CL5010BB Manuel utilisateur
