Cobra 29 LX LE Manuel de référence

Consumer Response Group

6500 W. Cortland Street *Chicago, IL 60707 *Phone: 773-889-8870 * FAX: 773-622-2269

-------------------------------------------------------------------------------------------------------------------

September 8, 2011 Page 1 of 5

TECHNICAL SERVICE BULLETIN

10076

MODEL(S): 29 LX and variants

DESCRIPTION: Display troubleshooting

ACTION: Does the backlight light up?

If the backlight lights up but the display is otherwise blank, then the ribbon cable

for the display may have become dislodged. Please refer to pages 2-3.

Is the display active, but dark?

If the display is dark even when power is turned on, then it may be a problem

with the backlight. Carefully inspect the display while power is turned on. Try

changing the channels. It might be that the display is actually working but the

backlight is out. If this is the case then the display will be dark but you should

see all the various details (numbers, icons, etc.). If you find this to be true, then

please refer to pages 4-5.

Is the display totally dead?

If the display is totally blank (no backlight, no details) then double-check

whether the radio has experience reverse polarity. If the reverse polarity diode is

blown (D23) then replace the diode and repair any associated damage.

If the problem persists

If you have gone through all the above troubleshooting tips and there is still a

problem, then try replacing the CPU/WX board, Cobra p/n 300-009.

ADJUSTMENTS: None

NOTES: None

Technical Service Bulletin 10076 Page 2 of 5

Ribbon Cable

There is a ribbon cable which runs from the display to the display PCB. If this cable becomes loose

then you may loose the display. Or the display may become intermittent. The backlight will still

illuminate, but the display will not show any information.

The following pages shows the location of the ribbon cable. Make sure that the cable is fully seated

into the connector. Please note that the connector has a locking mechanism. Lift up on the top piece to

release the lock, and push back down to engage the lock.

1. Lift up on the top piece to release the lock (see page 3).

2. Use the eraser end of a pencil to push the ribbon cable all the way down.

3. Push down on the top piece to engage the lock.

Technical Service Bulletin 10076 Page 3 of 5

Technical Service Bulletin 10076 Page 4 of 5

Backlight

If the backlight is out, then the display will appear dark but you will still see all the proper lettering, icons,

etc. Here is an example:

If this is the case, then measure the backlight voltages as shown on the following page.

Technical Service Bulletin 10076 Page 5 of 5

The backlight voltage should read between 5-18VDC depending on the DIM setting. If the voltages

are not present then replace the backlight power supply, Cobra p/n 306-004. The backlight power

supply is a metal can mounted to the side of the chassis:

If the voltage measure correctly but the backlight is still dark, then replace the backlight module,

Cobra p/n 306-003.

Autres manuels pour 29 LX LE

8

Table des matières

Autres manuels Cobra Émetteur-récepteur

Cobra

Cobra MR HH475 FLT BT/EU Manuel utilisateur

Cobra

Cobra 19 DX IV Manuel utilisateur

Cobra

Cobra MR HH500 FLT BT Manuel utilisateur

Cobra

Cobra 19 MINI Manuel utilisateur

Cobra

Cobra MR HH325VP Manuel utilisateur

Cobra

Cobra 29 LX LE Manuel utilisateur

Cobra

Cobra MR HH425LI VP Manuel utilisateur

Cobra

Cobra 29 LTD ST Manuel utilisateur

Cobra

Cobra MR HH475 FLT BT Manuel d'instructions

Cobra

Cobra 19 Ultra III Manuel utilisateur

Cobra

Cobra MR HH425 LI VP Manuel d'instructions

Cobra

Cobra MR HH600W FLT GPS BT Manuel utilisateur

Cobra

Cobra FRS.200 Manuel utilisateur

Cobra

Cobra MARINE MR HH330 FLT EU Manuel utilisateur

Cobra

Cobra 29 WX NW BT Mode d'emploi

Cobra

Cobra 29 LX LE Mode d'emploi

Cobra

Cobra MR F77W GPS Manuel utilisateur

Cobra

Cobra 29 LX LE Manuel utilisateur

Cobra

Cobra LI-6050 Manuel utilisateur

Cobra

Cobra 19 DX IV Manuel utilisateur

Manuels Émetteur-récepteur populaires d'autres marques

Yaesu

Yaesu FT-7B Manuel utilisateur

Kenwood

Kenwood ProTalk TK-3201 Manuel utilisateur

Texas Instruments

Texas Instruments TLK10232 Manuel utilisateur

Mizuho

Mizuho MX-2 Guide produit

Kenwood

Kenwood TK-3180 Manuel d'utilisation et d'entretien

Blitz

Blitz MJ-398U Manuel utilisateur

Utilicom

Utilicom LongRanger 2050 Manuel utilisateur

Standart

Standart HX290UKA Manuel utilisateur

Altronix

Altronix Pace1PTM Manuel utilisateur

Kirisun

Kirisun PT2208 Manuel utilisateur

ELECRAFT

ELECRAFT KX2 Manuel utilisateur

Zodiac

Zodiac K3 Manuel utilisateur

Assa Abloy

Assa Abloy SecureComm HKC GSM-WIFI U Manuel utilisateur

Kenwood

Kenwood TK-2217 Manuel utilisateur

Siemens

Siemens PSO 4000 Manuel utilisateur

Kenwood

Kenwood TS-590SG Manuel utilisateur

Midland

Midland G8E-BT Manuel

ComNav

ComNav Mariner X2 Manuel utilisateur