Co2meter RAD-0102-6 Manuel utilisateur

INSERT IMAGE

CO2Meter

105 Runway Drive Ormond Beach, FL 32174 USA

(877) 678-4259

RAD-0102-6

Remote CO2 Storage Safety 3 Alarm

User Manual and Installaon Guide

Revision 01.02

2 | P a g e R A D - 0 1 0 2 - 6 / M a n u a l a n d I n s t a l l a t i o n G u i d e

Warning!

This product should only be used as described in

this manual. If the equipment is used outside of

the manner specied by CO2Meter, the protecon

provided by the equipment may be diminished.

This equipment should be installed/serviced by

qualied personnel only.

Please contact Support@CO2Meter.com for more

informaon.

 
 3 | P a g e            R A D - 0 1 0 2 - 6   / M a n u a l   a n d   I n s t a l l a t i o n   G u i d e  
 
 
Contents 
General information on Carbon Dioxide Safety................................................................................................4 
Introduction to the RAD-0102-6...........................................................................................................................5 
Key Features............................................................................................................................................................................. 5 
Display........................................................................................................................................................................................ 6 
Icons and Symbols ................................................................................................................................................................. 6 
Specifications........................................................................................................................................................... 7 
Layout .......................................................................................................................................................................8 
SEU (Sensor Unit)................................................................................................................................................................... 9 
RDU (Remote Display Unit)..............................................................................................................................................10 
Strobes.....................................................................................................................................................................................10 
Power .......................................................................................................................................................................................10 
Installation ............................................................................................................................................................ 11 
Operation .............................................................................................................................................................. 12 
Start-up....................................................................................................................................................................................12 
Quick Test the System........................................................................................................................................................12 
Unlocking/Locking Settings..............................................................................................................................................12 
Configuring AL1.....................................................................................................................................................................13 
Configuring AL2.....................................................................................................................................................................13 
Configuring AL3.....................................................................................................................................................................13 
Latch ON/OFF ........................................................................................................................................................................14 
Baro ON/OFF..........................................................................................................................................................................14 
Calibration ..............................................................................................................................................................................15 
System Test ............................................................................................................................................................................16 
Factory Reset.........................................................................................................................................................................16 
Maintenance......................................................................................................................................................... 17 
Warranty.................................................................................................................................................................................17 
Product Returns....................................................................................................................................................................18 
Support ....................................................................................................................................................................................18 
Contact Us ...........................................................................................................................................18 
 
 

4 | P a g e R A D - 0 1 0 2 - 6 / M a n u a l a n d I n s t a l l a t i o n G u i d e

General informaon on Carbon Dioxide Safety

5 | P a g e R A D - 0 1 0 2 - 6 / M a n u a l a n d I n s t a l l a t i o n G u i d e

Introducon to the RAD-0102-6

Thank you for selecting the RAD-0102-6 CO2 Storage Safety Three Alarm. This

monitor is designed to detect Carbon Dioxide levels in the ambient air to protect

employees and customers. CO2 monitors are required in most jurisdictions by

code. High concentrations of CO2 in conned spaces are dangerous and may lead

to health problems ranging from headaches and fatigue to asphyxiation and death.

This monitor has 3 audible and visual alarm levels with relays that are triggered at

5,000 ppm TWA, 5,000 ppm, and 30,000 ppm and can control a ventilation fan or

signal the re panel to send an alarm to the re department or monitoring

company. These standards meet IFC, NFPA, and NBIC requirements for monitoring.

Key Features

•(3) Safety alarms (Audible and Visible)

•NDIR sensor with extended lifespan

•Push button conguration

•4-20mA output for communication with Building Maintenance Systems

•(3) Dry contact relays triggered by each alarm level (NO or NC)

•Back-up battery connection available

•Easy calibration function

•Barometric pressure compensation

•Temperature compensation

•Alarm latching function

•Strobe accessories available: CM-1027 (Click HERE)

6 | P a g e R A D - 0 1 0 2 - 6 / M a n u a l a n d I n s t a l l a t i o n G u i d e

Display

Icons and Symbols

Icon/Symbol

Descripon

1216PPM

CO2 Level Icon: Displays the live ambient carbon dioxide levels of the area

being monitored. Updates every 2 seconds.

DIAG

Technician diagnostics feature. Communication test.

AL1

1st Alarm Icon: 1st alarm. (5,000TWA)

AL2

2nd Alarm Icon: Congurable 2nd alarm. (Default 5000ppm or 0.5% CO2)

AL3

3rd Alarm Icon: Congurable 3rd alarm. (Default 30,000ppm or 3% CO2)

CALI

Calibration Icon: (See page 14 for calibration instructions)

RCFS

Reset Factory Setting Icon: (See page 15 for reset instructions)

High CO2 Icon: Indicated CO2 levels greater than 5%

Alarm Icon: Appears after AL1 is triggered and will remain on display while

the monitor is in alarming state

Ventilation Icon: CO2 Levels exceed AL2 and Relay2 has been triggered.

7 | P a g e R A D - 0 1 0 2 - 6 / M a n u a l a n d I n s t a l l a t i o n G u i d e

Specicaons

CO2 Specication

Measurement Range

0 - 50,000ppm (5%) display

Display Resolution

10ppm at 0~10,000ppm;

0.01% at 1-5%

Accuracy

+/-200ppm or +/-10% reading

Pressure Dependence

Auto pressure compensation, built in barometer. (50 to 110

kPa)

Response Time

CO2: <2min by 90%

CO2 AL1 (TWA )

5000TWA

CO2 AL2

5000ppm Default (5000ppm, 1.0%, 1.5%, 2.0%, 2.5%, 3.0%.)

CO2 AL3

3.0% Default (2.0%, 2.5%, 3.0%, 3.5%, 4.0%)

Sound Alarm

80db@10cm

Warm-Up Time

<60 seconds at 22°C

Monitor Specication

Power Input

9~32VDC (12~24VDC recommended), 2A.

Backup Battery

6VDC (5.4V~7.0V), recommended capacity is 12AH

Relay 1

Dry contact relay controlled by AL1 (2Amp) (NO or NC)

Relay 2

Dry contact relay controlled by AL2 (2Amp) (NO or NC)

Relay 3

Dry contact relay controlled by AL3 (2Amp) (NO or NC)

4-20mA CO2

CO2: Range 0-50,000ppm

4-20mA TEMP

Temp: Range 32 to 122° F (0-50°C)

Dimensions

8.25-inch x 7.8-inch x 3-inch

Weight

1.5lbs (Monitor only)

Ingress Protection

IP54

Temperature Specication:

Temperature Range

32°F to 122°F (0°C to 50°C)

Display Resolution

0.1°F (0.1°C)

Display Options

°C/°F

Accuracy

Reading represents device temperature (NOT environment)

Response Time

20-30 minutes (Enclosure must equalize with environment)

Operating Conditions:

Temperature

32°F to 122°F (0°C to 50°C)

Humidity Range

0 ~ 95% RH non-condensing

Storage Conditions:

Storage Temperature

-4°F to 140°F (-20°C to 60 °C)

8 | P a g e R A D - 0 1 0 2 - 6 / M a n u a l a n d I n s t a l l a t i o n G u i d e

Layout

SEU (Sensor Unit)

RDU (Remote Display Unit)

A. CO2 Sensor

L. Buzzer

B. LCD display

M. Reset Button

C. Power (Green LED)

N. 4-20mA Output

D. AL1 (Red 1 LED)

O. Battery

E. AL2 (Red 2 LED)

P. DC Power Supply

F. AL3 (Red 3 LED)

Q. RDU Cable (RJ45)

G. Fault (Yellow LED)

R. Relay 3 (AL3)

H. Mode Button

S. Relay 2 (AL2)

I. UP Button

T. Relay 1 (AL1)

J. Down Button

U. Strobe Cable (RJ45)

K. Enter Button

V. Panel Holder

A. Power (Green LED)

I. Down Button

B. AL1 (Red 1 LED)

J. Enter Button

C. AL2 (Red 2 LED)

K. Buzzer

D. AL3 (Red 3 LED)

L. Strobe Cable (RJ45)

E. Fault (Yellow LED)

M. Output Cable (RJ45)

F. LCD display

N. Input Cable (RJ45)

G. Mode Button

O. Panel Holder

H. UP Button

9 | P a g e R A D - 0 1 0 2 - 6 / M a n u a l a n d I n s t a l l a t i o n G u i d e

SEU (Sensor Unit)

The SEU (Sensor Unit) should be mounted in a room where CO2 is likely to

accumulate, this can be caused by a leak or use of the gas in production

applications.

The large LCD displays the ambient CO2 concentration.

The SEU Display functions:

- “DIAG” function executes communication tests between the SEU and RDU.

- “AL1” is a xed 5000ppm TWA.

- “AL2” has CO2 level of 5000ppm, 1.0%, 1.5%, 2.0%, 2.5%, 3.0%. (AL2 default

5000ppm)

- “AL3” has CO2 levels of: 2.0%, 2.5%, 3.0%, 3.5%, 4.0%. (AL3 default is 3.0%)

- “CALI” function allows the user to perform calibration, when necessary.

“RCFS” function allows the user to reset the unit to the original factory settings.

When the RAD-0102-6 detects a CO2 value that exceeds 5,000ppm, the AL1 (Red 1

LED) will blink, and Relay 1 will be triggered.

When the CO2 TWA value drops below 5000ppm (TWA), AL1 (Red1 LED) will stop

blinking and Relay 1 will be inactive.

When the RAD-0102-6 detects a CO2 value that exceeds the AL2 CO2 level, AL2 (Red

2 LED) will blink, the buzzer will sound, and Relay 2 will be triggered.

When the CO2 value drops below the AL2 CO2 level, AL2 (Red 2 LED) will stop

blinking, the buzzer will stop, and Relay 2 will be inactive.

If the CO2 concentration continues to rise and exceeds the AL3 CO2 level, AL2 (Red

2 LED) and AL3 (Red 3 LED) will ash together. The tempo of the ashing and buzzer

will increase. RAD-0102-6 will latch after this event. When the CO2 value drops

below the AL3 CO2 level and then below the AL2 CO2 level, the ashing and buzzer

will stop, but the Fault LED will remain ashing.

The RAD-0102-6 must be reset, by means of the reset button of RAD-0102-6 (See

item M in layout) or power cycle the unit.

10 | P a g e R A D - 0 1 0 2 - 6 / M a n u a l a n d I n s t a l l a t i o n

G u i d e

The Power (Green LED) will light continuously when the power is normally supplied.

If the device is powered by a battery, the Power (Green LED) will ash, and battery

indicator will appear and change with the battery voltage.

If the communication cable between the SEU & RDU is not connected securely, the

communication cable is loose or disconnected from the (RJ45) connectors, the fault

LED of SEU will blink as a reminder for the user to reconnect the cable. If the

communication cable is inserted into the wrong port on RDU, after about one

minute, the “Er7” will ash on the RDU LCD. Please plug the cables into the correct

ports on RDU and the unit will work normally.

RDU (Remote Display Unit)

The RDU displays the data from the SEU and provides visual and audible indication

that the SEU is in alarm status. The RDU is NOT an external/second sensor. The

RDU is connected to the SEU with a CAT5 cable. A 25-foot CAT5 cable is provided.

Users can source additional cable lengths as needed. The RDU should be placed

where it can be conveniently observed (eye level) before entering the room/space.

The “DIAG” function can test the communication between the SEU and RDU (see

9.1). Resetting the RAD-0102-6 CO2 Monitor is only available from SEU.

Strobes

The RAD-0102-6 can be equipped with strobes for additional visual alarms. Using

CAT5 cables, connect the strobes to the correct RJ45 ports on the SEU and RDU. If

CO2 levels exceed AL2, the strobe will ash. If the CO2 level exceeds AL3, the strobe

tempo increases. Please visit www.CO2Meter.com for strobe package. Part

Number: CM-1027.

Power

The RAD-0102-6 comes pre-wired with a 12V power supply that plugs in to a wall

outlet. The 12V power supply can be removed and 24V DC can be wired directly to

the device through the terminal block. Please use a 24V DC power converter to

properly convert your AC power source.

Table des matières

Manuels Stockage populaires d'autres marques

QNAP

QNAP TS 32PXU Series Manuel utilisateur

LaCie

LaCie RUGGED RAID Manuel utilisateur

Freecom

Freecom CLS DOCK Manuel utilisateur

PNY

PNY Attache P-FD64MBATT3 Manuel utilisateur

HP StorageWorks MSL2024 Manuel utilisateur

OLT

OLT 6x6 Maximizer Manuel utilisateur

Transcend

Transcend JetFlash 160 Manuel utilisateur

LaCie

LaCie RUGGED MINI Manuel utilisateur

Thunderbolt

Thunderbolt 600 Manuel utilisateur

Panasonic

Panasonic LB-DH8 series Manuel

Intel

Intel RAID High Availability Manuel utilisateur

LaCie

LaCie 12big Thunderbolt 3 Manuel utilisateur

Spectra Logic

Spectra Logic T-Series Spectra T50e Manuel utilisateur

Panasonic

Panasonic LKM-F931-1 Manuel utilisateur

Tabernus

Tabernus Enterprise Erase E2400 Manuel utilisateur

Rocstor

Rocstor COMMANDER 3F series Manuel utilisateur

HP P9000 Manuel utilisateur

Western Digital

Western Digital Ultrastar Data60 Manuel utilisateur