Closet Maid ShelfTrack Instructions de montage

ShelfTrack ®

Installation Tips

/18

Tools you will need for assembly:

.50 in.

.25 in.

PARTS

3/16 in. Toggle / 3 in. Bolt #12 x 2 in. Panhead Screw 1/4 in. Anchor

Shelf Caps Closet Rod Cap Shoe Shelf Support and Inserts

Closet Rod Support Shelf Bracket Hang Track

Standard

Closet Rod

1Prepare for hang track installation

A) CUT TRACK IF NECESSARY

Remember to always cut between the holes.

B) DETERMINE WALL TYPE

Determine whether you will be mounting the hang track (and standards) into drywall or

concrete. (Note: Drywall installation requires mounting to at least one stud.)

The installation is in a later step, but it is important to understand which method you will

use.

C) DETERMINE PROPER HARDWARE FOR WALL TYPE

Locate and identify proper hardware for your wall type.

THROUGH DRYWALL

INTO STUD

DRYWALL

USE ANCHOR/SCREW FOR ALL HOLES

CONCRETE

Mark the Hang Track Location on closet wall

A) DETERMINE “TOP” AND “BOTTOM”

OF HANG TRACKS

B) DRAW A LEVEL LINE 7 ft. UP FROM

THE FLOOR

Place BOTTOM edge of hang track ON MARKED

LINE and AGAINST EACH SIDE WALL in closet.

Mark all the hole locations on wall.

(NOTE FOR DRYWALL INSTALLATION: Be sure

at leaset one hole aligns with a stud.)

3Attach Hang Track to wall using specic hardware

A) DRYWALL

Drywall installations require at least

one hole to align with a stud (see

diagram).

For holes which go ONLY into

drywall, drill 1/2 in. holes and use

3/16 in. toggle/bolt**.

For hole(s) which align with stud(s),

use #12 x 2 in. panhead screw

directly into stud (do not predrill hole).

B) CONCRETE

For ALL holes, drill a 1/4 in. hole and

insert an anchor.

Thread a screw through track and into

each anchor.

** Insert bolt through hole in hang track and re-install toggle onto end of bolt. Repeat for all

toggles and bolts. Place hang track against wall at the hole locations. Squeeze toggle bolts

and push through drilled holes. Tighten bolts to secure hang track to wall.

A) Space standards NO MORE than 24 in. apart and a MINIMUM of 2 in. in from end of hang

track. Measure from the CENTER of one standard to the CENTER of the next standard.

B) Attach standards as shown in locations marked for

your wall width. Be sure to measure from center

of one standard to center of next standard. Never

place standards more than 24 in. apart, less than

2 in. from end of hang track, or more than 4 in.

from from end of hang track (for standards closest

to side walls).

Secure each standard to wall through second or

third hole location with one supplied screw/anchor.

To do so, drill 1/4 in. holes at hole locations,

insert anchor, and attach standard to wall with 2 in.

screw.

Install standards onto hang track

Install brackets

Insert shelf brackets into standards at desired height for

each shelf.

Each 8 ft. shelf requires 5 shelf brackets.

Each 6 ft. shelf requires 4 shelf brackets.

Each 4 ft. shelf requires 3 shelf brackets.

Each 2 ft. shelf (or cut 1 ft. shelves) require 2 shelf

brackets.

Install shelves

A) Allow a 1 in. - 2 in. overhang (beyond bracket). Never allow more than a 4 in. overhang.

B) FOR SHELVES THAT

REQUIRE CUTTING:

Put shelf on brackets so one side is

ush with wall.

Allow an equal overhang (from

brackets) on both sides. Measure

amount to be cut.

Remove shelf and cut with hacksaw

or bolt cutter.

Do not make cuts where vertical

spacers are on front lip of shelf.

C) Place shelf caps onto exposed shelf

wires.

6Install shelves (Cont.)

Install shoe shelf

Rest shelf on each shelf bracket at desired

location.

Pull shelf forward and allow front to “drop”

over nose of shelf brackets (nose of each shelf

bracket will t between wires).

Push shelf backwards so back wire ts into

shelf bracket slots.

Firmly pull shelf forward at each bracket

location to lock shelf into place.

Install shoe shelf

A) Attach insert onto end of shoe shelf support

as shown.

B) Attach shoe shelf supports to

longest standards at bottom

right.

NOTE: For proper installation, turn

shoe shelf upside down so lip faces

up before installing.

• Attach shoe shelf onto shoe shelf

supports by placing back of shelf into

slots at back of shoe shelf

support. Pull shelf forward and lower

front of shelf onto shoe shelf support.

Insert as shown.

Table des matières

Autres manuels Closet Maid Stockage

Closet Maid

Closet Maid SuperSlide 5637 Manuel utilisateur

Closet Maid

Closet Maid 3120 Instructions d'installation

Closet Maid

Closet Maid 3-Cube Storage System 8178 Manuel utilisateur

Closet Maid

Closet Maid 432600 Manuel utilisateur

Closet Maid

Closet Maid 6-Cube Storage System Manuel utilisateur

Closet Maid

Closet Maid 2-Door Versa Cabinet 12075 Manuel utilisateur

Manuels Stockage populaires d'autres marques

QNAP

QNAP TS 32PXU Series Manuel utilisateur

LaCie

LaCie RUGGED RAID Manuel utilisateur

Freecom

Freecom CLS DOCK Manuel utilisateur

PNY

PNY Attache P-FD64MBATT3 Manuel utilisateur

HP StorageWorks MSL2024 Manuel utilisateur

OLT

OLT 6x6 Maximizer Manuel utilisateur

Transcend

Transcend JetFlash 160 Manuel utilisateur

LaCie

LaCie RUGGED MINI Manuel utilisateur

Thunderbolt

Thunderbolt 600 Manuel utilisateur

Panasonic

Panasonic LB-DH8 series Manuel

Intel

Intel RAID High Availability Manuel utilisateur

LaCie

LaCie 12big Thunderbolt 3 Manuel utilisateur

Spectra Logic

Spectra Logic T-Series Spectra T50e Manuel utilisateur

Panasonic

Panasonic LKM-F931-1 Manuel utilisateur

Tabernus

Tabernus Enterprise Erase E2400 Manuel utilisateur

Rocstor

Rocstor COMMANDER 3F series Manuel utilisateur

HP P9000 Manuel utilisateur

Western Digital

Western Digital Ultrastar Data60 Manuel utilisateur