CLIVET KJRP-75A Mode d'emploi
PEMF00001
IA19M012ML-00
INSTALLATION
& OWNER’S MANUAL
In-built controller KJRP-75A
Thank you very much for purchasing our product.
Before using your unit, please read this manual carefully and keep it for future reference.
This manual gives detailed description of the precautions
that should be brought to your attention during operation.
In order to ensure correct service of the wired controller
please read this manual carefully before using the unit.
For convenience of future reference, keep this manual after
reading it.
CONTENTS
1 OPERATION
1.1 Operation precautions 01
1.2 Operation conditions 02
1.3 Main functions 02
1.4 User interface 03
1.5 Instructions for use 04
1.6 Further details 06
2 INSTALLATION
2.1 Safety precautions 09
2.2 Installation accessories 10
2.3 Installation dimensions 11
2.4 Installation method 12
2.5 Schematic drawing of installation 19
Means improper handling may lead to personal death
or severe injury.
CAUTION
Means improper handling may lead to personal injury
or property loss.
1 OPERATION
1.1 Operation precautions
Read the safety precautions carefully before installing, and
must be obeyed.
WARNING
This manual uses the following icons:
Prohibit Follow the guide lines
Please entrust the distributor or professionals to install the unit.
Before cleaning or maintenance, please cut off the power, and
prohibit to use water for washing, to prevent electrical shock.
01
Do not operate by wet hand, to prevent electrical shock.
Do not use pesticide, disinfectant and flammability spray
materials to spray directly, otherwise will cause fire or
deformation.
Do not peel off the button and the cover by hand, to prevent
electrical shock.
1.2 Operation conditions
Voltage input DC 12V
Operating ambient temperature range
-10~43°C
Operating ambient humidity range ≤ RH90%
1.3 Main functions
1. Connected to IDU main control board via 5-core shielded
cable;
2. Setting IDU operating status by tapping touch keys;
3. LED display.
02
1.4 User interface
Cooling Heating Dry Auto
Follow Me
Display Area Of the
Wired Controller
Automatic Fan Speed
Mode Button
Running Indicator
Remote Signal
Receiving Area
Temperature
Fan Speed
Fan Speed
Button
Temp. Setting
Button
Backlight Button On/Off Button
03
1.5 Instructions for use
1.5.1 Basic setting
1 2 3 4 5
1 Tap Mode button
The operating mode changes in the
following order:
Heating
Dry
Auto
2 Adjust temperature
Temperature range 17°C~30°C
3 Tap Fan Speed button
Seven fan speeds and Auto available.
4 Tap On/Off button
To start the unit and send all the configured
parameters.
5 Tap Backlight button
Backlight is on by default. Tap Backlight button
to turn it off.
04
CAUTION
If the wired controller is placed in a box, it may not
accurately detect the ambient temperature !
1.5 Instructions for use
1.5.2 "Follow Me" Operation Process
The Follow Me function is disabled by default.
After active the Follow Me function, controller
will showing the room temp which detect by
the controller self, and send the value to
fancoil every 3 mins, to replace the value
which detect by the room temp sensor of
fancoil sensor.
Start or exit Follow Me
Long press the Up button + Down button for
2s to start (or to exit) the Follow Me function.
The Follow Me function icon is turn on (or turn
off) .
05
CAUTION
Do not peel off the buttons and liquid crystal cover, to
prevent electric shock!
1.6 Further details
1.6.1 Supplementary instructions
Fan Speed button :
Fan speed cannot be set in Dry/Auto mode (Auto displayed).
Backlight mode:
1
）
Steady On: means backlight is normally on.
Tapping to start the unit can enter the backlight steady
on mode.
If backlight is off, tapping can switch to steady on mode.
2
）
Auto Off: means backlight is automatically off after 4s.
If backlight is off, tapping any button (except backlight and
On/Off) can switch to Auto Off mode.
CAUTION
06
No.
1
Error
Error
Name
E2PROM
communication error
Remarks
Unit stopped; unrecoverable
Fault
Code
E7
2 Error
Wired controller
temperature sensor
port abnormal
The wired controller can
operate normally after the
wired controller temperature
sensor fails.
There are two cases:
(1)
When the Follow Me
function is enabled,
the E0 code is displayed E0
(not displayed during
operation), and the main
board is controlled by
the temperature of the air
return port.
(2)
The E0 code is not
displayed when the
Follow Me function is disabled.
3 Error
4 Error
Room temperature
(air return port)
sensor port abnormal
Coil sensor (T2C)
port abnormal
Unit stopped; automatic
recovery after clearing E2
Unit stopped; automatic
recovery after clearing
07
E3
Ce manuel convient aux modèles suivants
1
Table des matières
Autres manuels CLIVET Contrôleurs
