Classe Audio CAP-100 Manuel utilisateur

CLASSÉ AUDIO

CAP-100

REMOTE CONTROL

INTEGRATED AMPLIFIER

CAP-100

OWNER'S MANUAL

CAP100, Issue 2, June 97

CLASSÉ DESIGN PHILOSOPHY

1. REPEATED LISTENING DESIGN SESSIONS

Fine tuning of sound by exchanging and mixing of parts (transistors, capacitors, wiring, PCB boards,

etc.), and adjusting many specific operating voltages within proper engineering ranges, producing an

overall sonic recipe giving the most natural harmonic realism of music typical of instruments in a

live performance.

2. UPGRADABLE SINGLE CIRCUIT DESIGNS

All Classé products (all preamps, all amps and integrated amplifier) share exactly the same circuit

design philosophy (excluding moving coil and moving magnet phono circuits). This means all

amplifiers and all high level circuits of the preamps benefit from the same design goals. Similar

circuits are then tailored to different power levels, etc. Differences between less expensive models

and more expensive models are parts quality and complement, power supply extravagance and the

amount of filtering, etc. as well as features and packaging.

This means that for years Classé has been constantly sonically fine tuning and technically upgrading

this circuit design and its application, thus reaching a very high level of natural musical enjoyment,

as well as excellent reliability which benefits all models - least expensive, most expensive,

integrated amplifier, preamps and amplifiers alike.

3. EXTREME LONG LIFE IN REAL WORLD CONDITIONS

Choosing the best attainable quality parts and materials combined with the advantages of the two

above-mentioned areas provide Classé owners with years of proven trouble free reliability and

musical enjoyment.

CAP100, Issue 2, June 97

CAP-100

OWNER'S MANUAL

TABLE OF CONTENTS

UNPACKING & SET-UP........................................….......... 4

A.C. LINE POWER................................................................ 5

INPUTS................................................................................... 6

OUTPUTS .............................................................................. 8

FRONT PANEL CONTROLS................................................ 9

PROTECTION CIRCUIT.........................................….......... 13

FEATURES AND SPECIFICATIONS .......................…..... 21

CAP100, Issue 2, June 97

UNPACKING & SET-UP

Your CLASSÉ CAP-100 integrated amplifier has been carefully wrapped in heavy gauge

plastic, packed in semi-rigid foam and contained in a special box. To remove the unit, open and spread

the top flaps of the box. By its sides, lift out the entire unit with foam pieces intact. Remove each foam

side by pulling straight out. Remove the plastic wrap and inspect the unit for any concealed damage.

Apart from this owner's manual, please ensure the following has also been included:

1) DETACHABLE LINECORD.

2) ALLEN KEY FOR TOP COVER.

3) REMOTE CONTROL UNIT (Allen key and Batteries: AAA x 2 included).

Please report any damage or missing parts to your dealer promptly.

Place the CAP-100 at or near its final set-up position, allowing 8 inches (20 mm.) at the rear for

tightening the speaker output connectors and inserting the interconnects. For optimum sonic

performance, we recommend the optional CLASSÉ REFERENCE A.C. LINE CORD. Consult your

dealer regarding this accessory.

The power transformer in the CAP-100 is located at the front/center of the unit. Ideally, a few

feet should separate this area from components that are susceptible to pick up hum. These include

turntables and interconnect cables. In terms of providing adequate airspace for cooling, a clearance of at

least 6 inches (15 mm.) should be left above the unit.

Check the serial number sticker on the back of the unit for the correct operating voltage. The

CAP-100 has one A.C. line fuse, inside the unit, at the back left hand side (facing the unit) directly

besides the small auxiliary transformer, the rating should be as follows:

FOR 100 TO 120 VOLTS : 4 AMPS SLO-BLOW 250V.

FOR 220 TO 240 VOLTS: 3 AMPS SLO-BLOW 250V.

CAP100, Issue 2, June 97

A.C. LINE POWER

When the CLASSÉ CAP-100 is first plugged in, only the auxiliary transformer is powered on.

To actually turn the unit on, the POWER switch situated on the front right hand side of the panel (fig.3

page 14) has to be activated. When the power switch is pressed, the MUTE LED will be flashing for 30

seconds. During this period, there will be no response from any of the functions except for the POWER

switch (please note that at this stage, the output terminals of the amplifier section are already

‘connected’ to the loudspeakers).While thoroughly musical shortly after turn-on, the integrated amplifier

will exhibit "sonic growth" during its first 300 hours of use.

SAFETY FEATURE:

The CAP-100 integrated amplifier is designed with an auto-shut down circuit that engages after

an AC power failure. Press the power switch to re-activate the unit after a power shut down

This feature will prevent any turn-on surges or unstable output from reaching the integrated

amplifier and possibly the loudspeakers. Similarly, make sure the MUTE is ON (STEADY GREEN)

again when powering down the unit.

CAUTION:

DISCONNECT AC LINE CABLE WHILE MAKING ALL CONNECTIONS. "FLOATING THE GROUND” OR

DEFEATING THE GROUND ON A 3-PRONG LINECORD MAY CREATE A SHOCK HAZARD. CONNECT ALL

INTERCONNECT CABLES BETWEEN THE ELECTRONICS BEFORE CONNECTING THE A.C.LINECORDS

TO THE WALL OUTLETS. THIS WILL REDUCE THE POTENTIAL SHOCK HAZARD.

CAP100, Issue 2, June 97

INPUTS

The input jacks are clearly marked on the back of the CAP-100 (fig.4 page 15). The

following inputs are provided: AUX/PHONO, VIDEO, CD, TUNER, BALANCED, TAPE and

AMP.

AUX/PHONO INPUT

When selected PHONO\AUX, this input serves as a high level input only. Use with sources

such as VIDEO, CD, TUNER, etc.. The AUX/PHONO input could also be fitted with an

OPTIONAL PHONO BOARD plug in module installed in the unit. A ground screw is provided

adjacent to the AUX/PHONO input jacks.

The following steps should be performed to install or remove the phono board.

INSTALLATION OF THE PHONO BOARD

1) Disconnect the A.C. line cord from the wall outlet.

2) Remove the top cover with the supplied Allen key.

3) Locate and replace the two mounting screws (see fig.6, page 20) with the supplied stand-offs.

4) Remove jumpers J5, J6 and J13, J14 (see fig.6, page 20). Check if the extension sockets are

in place on the reverse side of the phono board.

5) Install and secure the phono board using the screws removed previously in step 3, make

sure that all connectors are properly aligned.

6) Set MM/MC jumpers to the desired position. All six of these jumpers are located at the far

right of the phono board (see fig.7, page 21). Please note that for ALL HIGH OUTPUT MC

cartridges, the jumpers have to be SET AT MM.

7) Replace the top cover.

CAP100, Issue 2, June 97

REMOVAL OF THE PHONO BOARD

1) Disconnect the line cord from the wall outlet.

2) Remove the top cover with the supplied Allen key.

3) Remove the screws securing the phono board, remove the phono board and the stand offs,

replace the screws where the stand offs were removed (see fig.6, page 20) to secure the main

board.

4) Replace jumpers J5, J6 and J13, J14 (see fig.6, page 20) on the main board. Jumpers from the

phono board can be used for that purpose.

5) Replace top cover.

VIDEO, CD, TUNER

These are all high level inputs sharing exactly the same characteristics, and may be

interchanged if so desired.

BALANCED

The BALANCED INPUT is a true differential high level input, wired as follows:

PIN 1: GROUND

PIN 2: POSITIVE (NON-INVERTED) SIGNAL

PIN 3: NEGATIVE (INVERTED) SIGNAL

It may be used with CD players that have a balanced output, or any other high level balanced

sources.

CAP100, Issue 2, June 97

TAPE IN

The TAPE IN of the CAP-100 integrated amplifier should be connected to the LINE OUT or

TAPE OUT of the tape deck. The TAPE input does not appear on the selector switch. It is activated

by the TAPE button. (See FRONT PANEL CONTROLS: TAPE BUTTON.)

AMP IN

The SEPARATE button can be activated if the desire is to use this single ended input. By

activating the SEPARATE switch, the preamplifier section is decoupled from the amplifier section

that will permit to connect a separate preamplifier to the AMP input at the back of the unit.

CAP100, Issue 2, June 97

OUTPUTS

PREAMP OUT

The Classé CAP-100 integrated amplifier has a regular (single-ended) output that can be

used with an external power amplifier. This output is active at all times, regardless if the

SEPARATE button is activated or not.

TAPE OUTPUT

Whatever input is selected by the INPUT SELECTOR will be fed to the TAPE OUTPUT

jacks. This should be connected to the TAPE IN or LINE IN of the tape deck.

LOUDSPEAKER OUTPUT

The Classé CAP-100 is equipped with two pairs of 5 way binding posts (one for each

channel) which allows to hook up almost all available types of speaker cable connectors.

CAP100, Issue 2, June 97

FRONT PANEL CONTROLS

POWER

When the POWER BUTTON is pressed, this will initialise the start up mode, the MUTE

LED will be flashing for 30 seconds. During these 30 seconds, there will be no response from the

remote control functions, the mute button, the tape button and the separate button, only the power

button can be reactivated to turn off the unit during this sequence.

INPUT SELECTOR

This will select one of the seven inputs connections on the integrated amplifier, except TAPE

IN (see TAPE BUTTON) and AMP IN (see SEPARATE). The selector switch is silent and will

prevent pulses when switching positions. However, it remains good practice to REDUCE THE

VOLUME CONTROL LEVEL or to activate MUTE ON (steady GREEN LED) when changing the

input selection.

TAPE

In the SOURCE position, the integrated amplifier will process the signal as chosen by the

INPUT SELECTOR. In the TAPE position, the preamp will process the TAPE INPUT signal,

overriding the INPUT SELECTOR.

Autres manuels pour CAP-100

Table des matières

Autres manuels Classe Audio Amplificateur

Classe Audio

Classe Audio DR-10 Manuel utilisateur

Classe Audio

Classe Audio CA-2300 Manuel utilisateur

Classe Audio

Classe Audio CAP-151 Manuel utilisateur

Classe Audio

Classe Audio CRCD Manuel utilisateur

Classe Audio

Classe Audio Classe Audio Manuel utilisateur

Classe Audio

Classe Audio CP-50 Manuel utilisateur

Classe Audio

Classe Audio Delta MONO Manuel utilisateur

Classe Audio

Classe Audio CP-800 Manuel utilisateur

Classe Audio

Classe Audio CAP-2100 Manuel utilisateur

Classe Audio

Classe Audio CP-700 Manuel utilisateur

Classe Audio

Classe Audio P-151 Manuel utilisateur

Classe Audio

Classe Audio OMEGA - V1.1 Manuel utilisateur

Classe Audio

Classe Audio CA-5200 Manuel utilisateur

Classe Audio

Classe Audio 100-A Manuel utilisateur

Classe Audio

Classe Audio CAV-500 Manuel utilisateur

Classe Audio

Classe Audio CP-65 Manuel utilisateur

Classe Audio

Classe Audio CP-40 Manuel utilisateur

Classe Audio

Classe Audio CA-2100 - 3 Manuel utilisateur

Classe Audio

Classe Audio Sigma SSP Manuel utilisateur

Classe Audio

Classe Audio DR 25 Manuel utilisateur

Classe Audio

Classe Audio CA-400 Manuel utilisateur

Classe Audio

Classe Audio CAP-2100 Manuel utilisateur

Classe Audio

Classe Audio CA-3200 Manuel utilisateur

Classe Audio

Classe Audio DR-6 Manuel utilisateur

Manuels Amplificateur populaires d'autres marques

ASTRO

ASTRO HVO V40 P Manuel utilisateur

Marantz

Marantz SUPERSCOPE BLA-545 Instructions de montage

NAD

NAD CI980 Manuel utilisateur

Technics

Technics SE-CH770 Manuel utilisateur

Harman Kardon

Harman Kardon HK6300 Manuel utilisateur

NAD

NAD T975 Manuel utilisateur

McIntosh

McIntosh MA6850 Manuel utilisateur

Electro-Harmonix

Electro-Harmonix ENGLISH MUFF’N Manuel utilisateur

Viatron

Viatron Autrix Manuel utilisateur

GME

GME GA9800 Manuel utilisateur

Atlas

Atlas CP700 Manuel utilisateur

Roland

Roland KC-1000 Manuel utilisateur

Pyle

Pyle PFMRA350BW Manuel utilisateur

Advantage

Advantage S-250 Manuel utilisateur

IRT Electronics

IRT Electronics DVA-3007 Manuel utilisateur

Dimavery

Dimavery BA-100 Series Manuel utilisateur

Sony

Sony XM-S400D Manuel utilisateur

Schertler

Schertler ROY X Manuel utilisateur