Clarke C2MS210MP Mode d’emploi

OPERATION & MAINTENANCE

INSTRUCTIONS

ORIGINAL INSTRUCTIONS GC0119 - ISS 1

SLIDING COMPOUND MITRE SAW

MODEL NO: C2MS210MP/C2MS250MP

PART NO: 6461545/6461550

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Servi[email protected]

INTRODUCTION

Thank you for purchasing this CLARKE Mitre Saw.

Before attempting to operate the machine, it is essential that you read this

manual thoroughly and carefully follow all instructions given. In doing so you

will ensure the safety of yourself and that of others around you, and you can

also look forward to the product giving you long and satisfactory service.

GUARANTEE

This CLARKE product is guaranteed against faulty manufacture for a period of

12 months from the date of purchase. Please keep your receipt as proof of

purchase.

This guarantee is invalid if the product is found to have been abused or

tampered with in any way, or not used for the purpose for which it was

intended.

Faulty goods should be returned to their place of purchase, no product can

be returned to us without prior permission.

This guarantee does not effect your statutory rights.

ENVIRONMENTAL PROTECTION

Recycle unwanted materials instead of disposing of them as waste.

All unwanted accessories and packaging should be sorted and

taken to a recycling centre for disposal in a manner which is

compatible with the environment.

Through purchase of this product, the customer is taking on the obligation to

deal with the WEEE in accordance with the WEEE regulations in relation to the

treatment, recycling & recovery and environmentally sound disposal of the

WEEE.

In effect, this means that this product must not be disposed of with general

household waste. It must be disposed of according to the laws governing

Waste Electrical and Electronic Equipment (WEEE) at a recognised disposal

facility.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

SAFETY WARNINGS

WORK AREA

1. Keep the work area clean and well lit. Cluttered and dark areas invite

accidents.

2. Do not operate power tools in explosive atmospheres, such as in the

presence of flammable liquids, gases or dust. Power tools create sparks

which may ignite the dust or fumes.

3. Keep children and bystanders away while operating a power tool.

Distractions can cause you to lose control.

ELECTRICAL SAFETY

1. Power tool plugs must match the outlet. Never modify the plug in any way.

Do not use adapter plugs with earthed (grounded) power tools. Unmodified

plugs and matching outlets will reduce the risk of electric shock.

2. Do not expose power tools to rain or wet conditions. Water entering a

power tool will increase the risk of electric shock.

3. Do not abuse the cable. Never use the cable for carrying, pulling or

unplugging the power tool. Keep the cord away from heat, oil, sharp edges

or moving parts. Damaged or entangled cords increase the risk of electric

shock.

4. When operating a power tool outdoors, use an extension cord suitable for

outdoor use. Use of a cable suitable for outdoor use reduces the risk of

electric shock.

5. If operating the power tool in a damp location is unavoidable, use a

residual current device (RCD) protected supply

PERSONAL SAFETY

1. Stay alert, watch what you are doing and use common sense when

operating a power tool. Do not use a power tool while you are tired or

under the influence of drugs, alcohol or medication. A moment of

inattention while operating power tools may result in personal injury.

2. Use safety equipment. Always wear eye protection. Safety equipment such

as dust mask, non-skid safety shoes, hard hat, or hearing protection used

for appropriate conditions will reduce personal injuries.

3. Avoid accidental starting. Ensure the switch is in the off position before

plugging in. Carrying power tools with your finger on the switch or plugging

in power tools that have the switch on invites accidents.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Servi[email protected]

4. Remove any adjusting key or wrench before turning the power tool on. A

wrench or a key left attached to a rotating part of the power tool may

result in personal injury.

5. Do not overreach. Keep proper footing and balance at all times. This

enables better control of the power tool in unexpected situations.

6. Dress properly. Do not wear loose clothing or jewellery. Keep your hair,

clothing and gloves away from moving parts. Loose clothes, jewellery or

long hair can be caught in moving parts.

7. A laser beam can cause serious eye injury. Never look into the laser outlet.

POWER TOOL USE AND CARE

1. Do not force the power tool. Use the correct power tool for your

application. The correct power tool will do the job better and safer at the

rate which it was designed.

2. Do not use the power tool if the switch does not turn it on and off. Any

power tool that cannot be controlled with the switch is dangerous and

must be repaired.

3. Disconnect the plug from the power source before making any

adjustments, changing accessories, or storing power tools. Such preventive

safety measures reduce the risk of starting the power tool accidentally.

4. Store idle tools out of the reach of children and do not allow persons

unfamiliar with the power tool or these instructions to operate the power

tool. Power tools are dangerous in the hands of untrained users.

5. Maintain power tools. Check for misalignment or binding of moving parts,

breakage of parts and any other condition that may affect the power

tools operation. If damaged, have the power tool repaired before use.

Many accidents are caused by poorly maintained power tools.

6. Keep cutting tools sharp and clean. Tools with sharp cutting edges are less

likely to bind and are easier to control.

7. Use the power tool and accessories in accordance with these instructions

and in the manner intended, taking into account the working conditions

and the work to be performed. Use of the power tool for operations

different from intended use could result in a hazardous situation.

ADDITIONAL SAFETY RULES FOR MITRE SAWS

1. Make sure all locking knobs and clamp handles are tight before starting

any task.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

2. Do not operate the saw without the guard in position, if the guard does not

function correctly or is not maintained properly.

3. Never use your saw without the kerf plate.

4. Never place either hand in the blade area when the saw is connected to

the electrical power source.

5. Never attempt to stop a saw in motion rapidly by jamming a tool or other

means against the blade; serious accidents can be caused unintentionally

in this way.

6. Before using any accessory consult the instruction manual. The improper

use of an accessory can cause damage.

7. Observe the maximum speed marked on the saw blade.

8. Always wear gloves when handling a saw blade.

9. Do not use blades of larger or smaller diameter than recommended. For

the proper blade rating refer to the technical data. Use only the blades

specified in the specifications section of this manual.

10. Do not use cracked or damaged saw blades.

11. Do not use any abrasive discs.

12. Raise the blade from the kerf in the workpiece prior to releasing the switch.

13. Make sure that the arm is securely fixed when performing bevel cuts.

14. The blade guard on your saw will automatically raise when the arm is

brought down and will lower over the blade when the arm is raised. The

guard can be raised by hand when installing or removing saw blades or for

inspection of the saw. Never raise the blade guard manually unless the saw

is switched off.

15. Keep the surrounding area of the saw well maintained and free of loose

materials, e.g. swarf and cut-offs.

16. Before use, check that the motor air slots are clean and free of swarf.

17. Replace the kerf plate when worn.

18. Disconnect the saw from the mains before carrying out any maintenance

work or when changing the blade.

19. Never perform any cleaning or maintenance work when the saw is still

running and the head is not in the rest position.

20. When possible, always mount the saw on to a bench or plywood base

which is then clamped to a bench or mount the machine to a purpose

built mitre saw stand available from your local Clarke dealer.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Servi[email protected]

SAFETY SYMBOLS

The following safety symbols are to be found on the product.

Wear eye protection

Wear ear defenders

Do not put your hand near the blade

Read instruction manual before use

Laser Radiation, Class 2 Laser: Do not stare

into the beam.

Take care not to damage the fence when using different

compound mitre angles.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

ELECTRICAL CONNECTIONS

Before switching the product on, make sure that the voltage of your electricity supply is

the same as that indicated on the rating plate. This product is designed to operate on

230V AC 50Hz. Connecting it to any other power source may cause damage.

This product may be fitted with a non-rewireable plug. If it is necessary to change the

fuse in the plug, the fuse cover must be refitted. If the fuse cover becomes lost or

damaged, the plug must not be used until a suitable replacement is obtained.

If the plug has to be changed because it is not suitable for your socket, or due to

damage, it should be cut off and a replacement fitted, following the wiring instructions

shown below. The old plug must be disposed of safely, as insertion into a mains socket

could cause an electrical hazard.

If the colours of the wires in the power cable of this product do not correspond with the

markings on the terminals of your plug, proceed as follows.

• The wire which is coloured Blue must be connected to the terminal which is

marked Nor coloured Black.

• The wire which is coloured Brown must be connected to the terminal which

is marked Lor coloured Red.

We strongly recommend that this machine is connected to the mains supply

via a Residual Current Device (RCD).

If in any doubt, consult a qualified electrician. DO NOT attempt any repairs

yourself.

This symbol indicates that this is a class II product and does not require

an earth connection.

WARNING! READ THESE ELECTRICAL SAFETY INSTRUCTIONS

THOROUGHLY BEFORE CONNECTING THE PRODUCT TO THE

MAINS SUPPLY.

WARNING! THE WIRES IN THE POWER CABLE OF THIS PRODUCT

ARE COLOURED IN ACCORDANCE WITH THE FOLLOWING CODE:

Blue = Neutral Brown = Live

Plug must be BS1363/A approved.

Always fit a 13 Amp fuse.

Ensure that the outer sheath of the cable is firmly held by the clamp

Neutral

(Blue)

Live

(Brown)

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Servi[email protected]

OVERVIEW

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

BEFORE USE

1. Remove the saw from the packaging carefully.

• The following items should be supplied with the saw. If anything is missing

contact your dealer.

BENCH MOUNTING

Holes are provided in all four feet to

facilitate bench mounting.

• Always mount your saw firmly

on a level surface to prevent

movement.

The saw can also be mounted to a

piece of 12.5 mm or thicker plywood

which can then be clamped to your

work bench or moved to other work

sites and re-clamped when required.

• When mounting your saw to a piece of plywood, make sure that the

mounting screws do not protrude from the bottom of the wood.

MITRE SAW STAND (NOT SUPPLIED)

You can also mount the mitre saw on

a purpose built stand available from

your Clarke dealer.

1 x Work Clamp 1 x Hexagon Key (6 mm)

1 x Dust Collection Bag 2 x Workpiece Supports

216 mm Diameter 40 Tooth Cutting

Blade fitted to the C2MS210MP

255 mm Diameter 48 Tooth Cutting

Blade fitted to the C2MS250MP

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Servi[email protected]

SETTING THE WORK SUPPORTS

1. Loosen the work support locking

screws.

2. With the saw upside down, slide

the work support guide rods

through the holes in the base of

the saw and secure with the

spring clips.

3. Set the saw upright.

4. Extend the work supports as

required and secure them in

place using the work support

locking screw.

5. The work support incorporates a

hinged end stop which can be

raised if required.

FITTING THE WORK CLAMP

1. Loosen the clamp support

thumbscrews.

2. Slide the work clamp post into one

of the clamp supports on either

side of the saw and tighten the

thumbscrew to lock it in place.

NOTE: When swivelling the saw to

one side the motor may

strike the clamp post.

3. Adjust the clamp to suit the

workpiece.

4. Tighten the upper thumbscrew to secure the work clamp.

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Clarke Scie

Clarke

Clarke Woodworker CMS10S2B Mode d’emploi

Clarke

Clarke Woodworker CTS14 Mode d’emploi

Clarke

Clarke CSS16VB Mode d’emploi

Clarke

Clarke Contractor CFIS 250 Manuel d'installation et d'exploitation

Clarke

Clarke Metalworker CBS45MD Mode d’emploi

Clarke

Clarke Woodworker CMS251 Manuel d'installation et d'exploitation

Clarke

Clarke CTS16 Manuel d'installation et d'exploitation

Clarke

Clarke METALWORKER CBS 7MC Manuel

Clarke

Clarke CAT32B Manuel d'installation et d'exploitation

Clarke

Clarke ZX-R Pro Series Mode d’emploi

Clarke

Clarke CMS255S Mode d’emploi

Clarke

Clarke WOODWORKER CBS250 Manuel d'installation et d'exploitation

Clarke

Clarke CCS305 Manuel d'installation et d'exploitation

Clarke

Clarke CPS160 Mode d’emploi

Clarke

Clarke Woodworker CTS10D Manuel d'installation et d'exploitation

Clarke

Clarke CMS10S2 Mode d’emploi

Clarke

Clarke CRS710B Mode d’emploi

Clarke

Clarke CCS12 Manuel d'installation et d'exploitation

Clarke

Clarke CMS 200 Manuel d'installation et d'exploitation

Clarke

Clarke CAT118 Manuel d'installation et d'exploitation

Clarke

Clarke CCO14C Mode d’emploi

Clarke

Clarke CON14110 Mode d’emploi

Clarke

Clarke Woodworker CTS10PLM Manuel d'installation et d'exploitation

Clarke

Clarke CT4014 Manuel utilisateur

Manuels Scie populaires d'autres marques

RIDGID

RIDGID BS1400 Manuel utilisateur

ATIKA

ATIKA BWS 400-2 Manuel utilisateur

RGC

RGC FS20 Manuel utilisateur

Makita

Makita M2300 Manuel utilisateur

IMET Spa

IMET Spa BASIC 300 PLUS SHI Manuel utilisateur

IMET Spa

IMET Spa SIRIO 370 AF-E Manuel utilisateur

Optimum

Optimum OPTisaw CS 275 Manuel utilisateur

Makita

Makita BPB180 Manuel utilisateur

Stihl

Stihl MS 462 C-M Manuel utilisateur

AEG

AEG TS 250 K Manuel utilisateur

Meec tools

Meec tools 004665 Manuel utilisateur

Makita

Makita LS1018L Manuel utilisateur

Ryobi

Ryobi RCS1400 Manuel utilisateur

DeWalt

DeWalt DCS391 Manuel utilisateur

Sealey

Sealey SA72 Manuel utilisateur

skilsaw

skilsaw SPT88 Instructions de montage

Urrea

Urrea SI810 Dimensions et guide d'installation

EINHELL

EINHELL BKG 210/1 Manuel utilisateur