Clarke CAT118 Manuel d'installation et d'exploitation

OPERATING & MAINTENANCE

INSTRUCTIONS

ORIGINAL INSTRUCTIONS GC0220 -rev 1

SABRE SAW

MODEL NO: CAT118

PART NO: 3110874

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

INTRODUCTION

Thank you for purchasing this CLARKE Sabre Saw. The CAT118 sabre saw is a

compact and ergonomic tool for cutting steel sheet, reinforced fiberglass,

aluminum, wood, etc, according to the blade being used.

Before attempting to use this product, please read this manual thoroughly and

follow the instructions carefully. In doing so you will ensure the safety of yourself

and that of others around you, and you can look forward to your purchase

giving you long and satisfactory service.

Please keep these instructions for future reference.

GUARANTEE

This product is guaranteed against faulty manufacture for a period of 12

months from the date of purchase. Please keep your receipt which will be

required as proof of purchase.

This guarantee is invalid if the product is found to have been abused or

tampered with in any way, or not used for the purpose for which it was

intended.

Faulty goods should be returned to their place of purchase, no product can

be returned to us without prior permission.

This guarantee does not effect your statutory rights.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

GENERAL SAFETY RULES

WORK ENVIRONMENT

1. Keep the work area clean and tidy.

2. Dress appropriately: - do not wear loose clothing or jewellery. Tie long hair

out of the way.

3. Keep children and visitors away - do not let children handle the drill.

4. Do not operate the saw where there are flammable liquids or gases.

5. Stay alert and use common sense - do not operate the saw when you are

tired or under the influence of alcohol, drugs or medication.

6. Always wear eye protectors when using the saw - Eye protection must

provide protection from flying particles from the front and the side.

7. Always wear ear protectors and face mask when using the saw.

8. Do not overreach - Keep proper footing and balance at all times.

USE OF AIR POWERED TOOLS

1. Never use any type of bottled gas as a source of power for an air tool.

2. Do not connect the air supply hose with your finger on the trigger.

3. Do not exceed the maximum pressure for the saw 90 psi / 6.2 bar.

4. Check hoses for leaks or worn condition before use and ensure that all

connections are secure.

5. Keep the air supply hose away from heat, oil and sharp edges.

6. Do not use this saw for any other purpose than that described in this

manual.

7. Do not fit this saw to any stand or clamping device that may damage it.

8. Do not carry out any alterations or modifications to this saw.

9. Always disconnect from the air supply when:

• Performing any maintenance

• The saw is not in use.

• The saw will be left unattended.

CAUTION: FAILURE TO FOLLOW THESE PRECAUTIONS COULD RESULT IN

PERSONAL INJURY, AND/OR DAMAGE TO PROPERTY.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

• Moving to another work area.

• Passing the saw to another person.

10. Never use the saw if it is defective or operating abnormally.

11. Always ensure the saw has stopped before putting it down.

12. The saw should be repaired if required by qualified service personnel.

13. Avoid damaging the saw for example by applying excessive force.

14. ALWAYS maintain the saw with care. Keep it clean for the best and safest

performance.

15. Quick change couplings should not be located at the air tool. They add

weight and could fail due to vibration.

16. Do not force or misuse the saw. It will do a better and safer job at the rate

for which it was designed.

17. Do not remove any labels. Damaged labels should be replaced.

18. This saw vibrates with use. Vibration may be harmful to your hands or arms.

Stop using the saw if discomfort, a tingling feeling or pain occurs. Seek

medical advice before resuming use.

19. Never carry the saw by the air hose.

20. Never carry the saw with your finger on the trigger.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

PRODUCT OVERVIEW

NO DESCRIPTION NO DESCRIPTION

1Blade 4SafetyTrigger

2 Blade securing screw 5 Air inlet

3Safetylock

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

COMPRESSED AIR REQUIREMENTS

• Use only clean, dry, regulated compressed air as a power source.

• Air compressors used with the tool must comply with the appropriate

European Community Safety Directives.

• A build-up of moisture or oil in the air compressor will accelerate

wear and corrosion in the tool. Ensure any moisture is drained from

the compressor daily and the inlet filter is kept clean.

• If an unusually long air hose is required, (over 8 metres), the line

pressure or the hose inside diameter may need to be increased.

• The air hose must be rated at least 150% of the maximum operating

pressure of the tool.

• A typical air line layout is shown above. If an automatic in-line filter/

regulator is used, it will keep the air tool in good condition, but

should be regularly checked and topped up with oil. SAE 10 oil

should be used and the lubricator adjusted to approx 2 drops per

minute.

• The minimum hose diameter should be 5/16”(8mm) ID and fittings

should have the same internal dimensions.

WARNING: COMPRESSED AIR CAN BE DANGEROUS. ENSURE THAT YOU

ARE FAMILIAR WITH ALL PRECAUTIONS RELATING TO THE USE OF

COMPRESSORS AND A COMPRESSED AIR SUPPLY.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

• Never exceed the maximum operating pressure for the air tool. It is

recommended that air pressure to this tool does not exceed 90 psi

(6.2 bar) at the tool when running. Higher pressures and unclean air

will shorten the life of the tool due to faster wear and is a possible

safety hazard.

BEFORE USE

FITTING THE BLADE

1. Slide the blade into the saw as

shown.

2. Secure the blade by tightening the

grub screw shown using the

hexagonal key supplied.

3. Identify the material and then

select the correct blade for your

operation.

4. Always use the correct saw blade

for the material for smooth and

fast cutting.

• It is recommended that

operators use 32T blades for cutting light sheet metal, body panels,

exhaust pipes, etc., use 24T blades for general purpose sawing

including aluminum and other soft materials, and use 18T blades for

cutting plastic, reinforced fiberglass, wood, etc.

WARNING: MAKE SURE THAT THE SAW IS DISCONNECTED FROM THE AIR

SUPPLY BEFORE INSTALLING, REMOVING OR REPLACING THE BLADE.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

CONNECTING THE AIR LINE

1. Remove the protective plug from

the air inlet and connect a suitable

hose as shown.

2. A gauze filter is fitted within the air

inlet. Ensure this is always in place

and is kept clean. The air line is

connected to the adapter,

preferably via a quick release

coupling (not supplied).

3. Connect the other end of the hose

to the compressed air supply.

4. Ensure the trigger is NOT depressed

when connecting the air line.

5. Turn on the air supply and check

for air leaks. Rectify any found

before proceeding.

• PTFE tape may be useful for

sealing threaded connections.

6. If required, connect an in-line mini oiler to the airline close to the air tool.

• A mini oiler helps to prolong the life of any air tool.

7. If a mini-oiler is not being used, run a few drops of oil through the air tool

before use. It can be entered through the airline inlet or via the hose at the

nearest connection to the air supply.

• Your sabre saw is now ready for use

• You can fit a whip hose with a quick fit coupling if required

(available from your Clarke dealer.)

USEFUL AIRLINE ITEMS FROM THE CLARKE RANGE

CAT150 Mini-Oiler:- Part No 3120164

8mm Rubber Whip Hose:-Part No 3120104

CAT58 6mm Recoil Hose with 1/4”bsp connectors (25 feet):-Part No 3110458

CAT59 6mm Recoil Hose with 1/4”bsp connectors (50 feet):-Part No 3110459

CRH9 9metres professional recoil hose:-Part No 3120100

CAR20PC Manual Air Hose Reel:-Part No 3126250

CAR15PC PVC hose in moulded case with auto re-wind:-Part No 3126000

See the latest catalogue for details of snap couplings & pressure gauges

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

OPERATION

OPERATING THE SAW

1. Slide the safety lock forward and

squeeze the trigger.

• Allow the saw to reach full

speed before use.

2. Release the trigger to stop the

saw. When the blade has stopped

remove it from the workpiece.

DISCONNECTING THE AIR SUPPLY

1. Do not disconnect the air supply hose until the air supply has been shut

down and the compressed air released from the hose.

2. Refer to the compressor instruction manual for the procedure to shut down

and release the compressed air.

3. Once the pressure has been released, disconnect the air supply hose from

the saw.

MAINTENANCE

Please note that factors other than the tools condition may effect its operation

and efficiency, such as reduced compressor output, excessive drain on the

airline, moisture or restrictions in the air-line, or the use of connector

DAILY

1. Before use, drain water from the air-line and compressor.

2. Lubricate the saw daily for optimum performance. Use a high quality airline

oil either via a lubricator in the air supply system or by placing a few drops

into the air inlet immediately before use. This should be carried out

regardless of whether or not an in-line lubricator is used.

WARNING: MAKE SURE THAT THE SAW IS DISCONNECTED FROM THE AIR

SUPPLY BEFORE STARTING ANY CLEANING OR MAINTENANCE

PROCEDURES.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

CLEANING & OVERHAUL

1. Keep the saw clean and free from debris.

2. If the saw becomes sluggish and the air supply is of good quality, it may be

necessary to replace worn or damaged parts.

3. Grit or gum deposits in the mechanism may eventually reduce efficiency.

This condition can be corrected by cleaning the air inlet filter and flushing

out the saw with gum solvent oil or an equal mixture of SAE No10 oil and

paraffin.

4. Failing this, the saw should be disassembled, thoroughly cleaned, dried

and reassembled. You may prefer to take the saw to your CLARKE dealer if

internal maintenance is required.

STORAGE

If the saw is to be stored or is idle for longer than 24 hours, run a few drops of

Clarke air-line oil into the air inlet and depress the trigger in order to lubricate

the internal parts.

When not in use, the saw should be disconnected from the air supply and

stored in a dry place out of the reach of children. Avoid storing in a damp

environment.

ACCESSORIES

A wide range of accessories is available including filter/regulators, lubricators,

high-pressure hoses (5 to 50 metres) etc.

Contact your CLARKE dealer for further information or CLARKE International

Service Department on 01992 565333.

Clarke Air Line Oil (part no. 3050825) is available from your CLARKE dealer

Replacement blades are available as follows:

Part no. 3110429

Autres manuels pour CAT118

Table des matières

Autres manuels Clarke Scie

Clarke

Clarke CON14 Mode d’emploi

Clarke

Clarke CBS300 Mode d’emploi

Clarke

Clarke CONTRACTOR CON850 Manuel

Clarke

Clarke Contractor CON185 Mode d’emploi

Clarke

Clarke contractor CON100 Manuel d'installation et d'exploitation

Clarke

Clarke CMS210 Mode d’emploi

Clarke

Clarke Contractor CCS2 Manuel d'installation et d'exploitation

Clarke

Clarke Woodworker CMS10S2B Mode d’emploi

Clarke

Clarke WOODWORKER CTS800B Manuel d'installation et d'exploitation

Clarke

Clarke CTS16 Manuel d'installation et d'exploitation

Clarke

Clarke METALWORKER CBS 7MC Manuel

Clarke

Clarke Woodworker MBS600B Manuel utilisateur

Clarke

Clarke woodworker CMS10 6501305 Manuel d'installation et d'exploitation

Clarke

Clarke CSS16VB Mode d’emploi

Clarke

Clarke CSS 300 Manuel d'utilisation

Clarke

Clarke CCS185B Mode d’emploi

Clarke

Clarke Woodworker CBS12WC Manuel d'installation et d'exploitation

Clarke

Clarke Woodworker CBS250C Mode d’emploi

Clarke

Clarke Woodworker CSS400B Manuel

Clarke

Clarke Woodworker CTS10C Manuel d'installation et d'exploitation

Clarke

Clarke WOODWORKER CBS205 Mode d’emploi

Clarke

Clarke CCO14B Mode d’emploi

Clarke

Clarke CBS250B Manuel utilisateur

Clarke

Clarke WoodWorker CCS1 Manuel d'installation et d'exploitation

Manuels Scie populaires d'autres marques

RIDGID

RIDGID BS1400 Manuel utilisateur

ATIKA

ATIKA BWS 400-2 Manuel utilisateur

RGC

RGC FS20 Manuel utilisateur

Makita

Makita M2300 Manuel utilisateur

IMET Spa

IMET Spa BASIC 300 PLUS SHI Manuel utilisateur

IMET Spa

IMET Spa SIRIO 370 AF-E Manuel utilisateur

Optimum

Optimum OPTisaw CS 275 Manuel utilisateur

Makita

Makita BPB180 Manuel utilisateur

Stihl

Stihl MS 462 C-M Manuel utilisateur

AEG

AEG TS 250 K Manuel utilisateur

Meec tools

Meec tools 004665 Manuel utilisateur

Makita

Makita LS1018L Manuel utilisateur

Ryobi

Ryobi RCS1400 Manuel utilisateur

DeWalt

DeWalt DCS391 Manuel utilisateur

Sealey

Sealey SA72 Manuel utilisateur

skilsaw

skilsaw SPT88 Instructions de montage

Urrea

Urrea SI810 Dimensions et guide d'installation

EINHELL

EINHELL BKG 210/1 Manuel utilisateur