Clarke FOCUS L17 Manuel utilisateur

Clarke Focus Boost

New

08/01/2013

Title

Revision

Date

Approved

Clarke Focus Boost

Do not put chemicals in the machine!

Open the filler neck (A, Fig.14).

(

For

machines

without

Chemical

Mixing

System

)

Use the front filler neck (B) or the rear filler neck (C) to fill the

tank (D) with asolution suitable for the work to be performed.

Refill to the reference mark “1” of the level check hose (H).

Always follow the dilution instructions on the label of the

chemical product used to prepare the solution.

The solution temperature must not exceed +104°F (+40°C).

WARNING!

Use

only

low-foam

and

non-flammable

detergents,

intended

for

automatic

scrubber

applications.

(

For

machines

with

Chemical

Mixing

System)

Fill the tank (D) with clean water by using the filler neck (B)

or the rear filler neck (C).

Refill to the reference mark “1” of the level check hose (H).

The water temperature must not exceed +104°F (+40°C).

Figure

Detergent

tank

filling

(For

machines

with

Chemical

Mixing

System)

Open the cover (E) and check that the recovery water tank

(F) is empty, otherwise empty it with the drain hose (G).

Carefully lift the tank (A, Fig. 15).

Open the cap (B).

Replace or fill the jug (C) with any standard gallon container

of detergent suitable for the work to be performed (highly

concentrated detergents).

Do not fill the detergent tank completely, leave afew

centimeters from the edge.

WARNING!

Use

only

low-foam

and

non-flammable

detergents,

intended

for

automatic

scrubber

applications.

NOTE

To install anew jug container, determine the cap size and

if it is the smaller cap, remove the reducing adapter from

the hose cap (B). Insert the suction tube into the jug (C).

Pushdown firmly on the cap (B) and twist at the same

time to put the cap back onto the jug (C).

In case of new system, system emptied for cleaning, etc.,

wait for the hoses to fill up, before starting the Chemical

Mixing System.

Clarke Focus Boost

New

08/01/2013

Title

Revision

Date

Approved

MACHINE

START

AND

STOP

Starting

the

machine

Prepare the machine as shown in the previous paragraph.

Insert the ignition key (A, Fig. 16) and turn it to "I".

Check that the green warning light (B) turns on (charged

battery).

If the yellow (C) or red warning light (D) turns on, turn the

ignition key back to “0” and charge the batteries (see the

procedure in Maintenance chapter).

Drive the machine to the working area:

·By pushing it with the hands on the handlebar (E) (only

for

FOCUS

S20

·By pushing it with the hands on the handlebar (E) and

pressing the switch (F) to move forward, or pressing the

switch (F) together with the switch (G) to move backward

(only for

FOCUS

L17,

FOCUS

L20,

FOCUS

L20

Cyl.,

BOOST

L20

The forward speed can be adjusted with the adjuster (H).

Lower the squeegee (I) with the lever (J).

Lower the brush/pad-holder deck (K) by pressing the pedal

(L).

Press the brush/pad-holder switch (M) and the vacuum

system switch (N).

Press the washing water flow control switches (O) as

necessary, depending on the type of cleaning to be

performed.

Start cleaning:

·(Only for

FOCUS

S20

)by pushing the machine with the

hands on the handlebar (E) and pressing the switch (F).

·(Only for

FOCUS

L17,

FOCUS

L20,

FOCUS

L20

Cyl.,

BOOST

L20

)by pushing the machine with the

hands on the handlebar (E) and by pressing the switch

(F). If necessary, the forward speed can be adjusted with

the adjuster (H).

NOTE

To move the machine forward, press either the left or

right switch (F) or both.

Stopping

the

machine

Stop the machine by using the handlebar (E) (Only for

FOCUS

S20

Stop the machine by releasing the switches (F) (Only for

FOCUS

L17,

FOCUS

L20,

FOCUS

L20

Cyl.,

BOOST

L20

Stop the brushes and the vacuum system by pressing the

switch (M). The vacuum system stops after afew seconds.

Lift the brush/pad-holder deck (K) by pressing the pedal (L).

Lift the squeegee (I) with the lever (J).

Turn the ignition key (A) to "0".

Make sure that the machine cannot move independently. ù

Figure

Clarke Focus Boost

New

08/01/2013

Title

Revision

Date

Approved

MACHINE

OPERATION

(SCRUBBING/DRYING)

Start the machine as shown in the previous paragraph.

If necessary, press the washing water flow control switches

(A and B, Fig. 17) as necessary, depending on the type of

cleaning to be performed.

If necessary, stop the machine and adjust the squeegee

with the knob (C) so that the rear blade (D) touches the floor

along all its length.

Machine

drive

controls

CAUTION!

These

procedures

must

performed

qualified

personnel

Clarke

personnel

only.

The machine speed and forward movement capability depends on

the floor type and on the choice of using brush or pad.

These can be adjusted by two screws (B and D, Fig.18), which

are on the brush plate, according to the following procedure:

–

Loosen the nut (A); when turning the adjusting screw (B)

counter-clockwise, the machine moves towards the left;

when turning it clockwise the machine moves towards the

right.

–

(Only for

FOCUS

S20

)loosen the nut (C); when turning the

adjusting screw (D) counter-clockwise, the machine speed

increases; when turning it clockwise the machine speed

decreases.

When the procedure is completed, tighten the nuts (A and/or C).

Figure

Clarke Focus Boost

New

08/01/2013

Title

Revision

Date

Approved

NOTE

For correct scrubbing/drying of floors at the sides of the

walls, Clarke suggests to go near the walls with the right

side of the machine (A and B, Fig. 19) as shown in the

figure.

CAUTION!

avoid

any

damage

the

floor

surface,

turn

off

the

brushes/pad-holders

when

the

machine

stops

one

place,

especially

when

the

extra

pressure

function

on.

Detergent

flow

adjustment

(For machines with Chemical Mixing System)

Turn the knob (A, Fig. 20) clockwise or counter-clockwise to

increase or decrease the detergent concentration.

The average detergent concentration values, matching the 4

colored areas of the scale (B), are shown in the figure.

To set the detergent quantity to zero, fully turn the knob (A)

counter-clockwise.

Figure

NOTE

The detergent concentration is kept constant even if the

washing water flow is changed with the switches (C) or

(D).

Working

with

brush/pad-holder

extra

pressure

function

turned

If the floor proves to be particularly difficult to clean, it is

possible to turn on the brush/pad-holder extra pressure

function by pressing the pedal (E) to position (E3).

CAUTION!

When

the

cylindrical

brush

deck

(S,

Fig.

Page

installed,

the

extra

pressure

function

not

enabled.

Figure

Clarke Focus Boost

New

08/01/2013

Title

Revision

Date

Approved

Battery

discharge

during

operation

Until the green warning light (A, Fig. 21) stays on, the

batteries allow the machine to work normally.

When the green warning light (A) turns off, and the yellow

warning light (B) turns on, it is advisable to charge the

batteries, because the remaining charge will last for afew

minutes (depending on battery characteristics and work to be

performed).

When the red warning light (C) turns on, batteries are fully

discharged. After afew seconds, the brush/pad-holder is

automatically tuned off, while the vacuum system and (only

for

FOCUS

L17,

FOCUS

L20,

FOCUS

L20

Cyl.,

BOOST

L20

)the drive system stay on, to finish drying the

floor and drive the machine to the appointed recharging area.

CAUTION!

not

use

the

machine

with

discharged

batteries,

avoid

damaging

the

batteries

and

reducing

the

battery

life.

TANK

EMPTYING

An automatic float shut-off system (A, Fig. 22) stops the vacuum

system when the recovery water tank (B) is full.

The vacuum system deactivation is signaled by asudden

increase in the vacuum system motor noise frequency, also the

floor has not dried.

CAUTION!

the

vacuum

system

turns

off

accidentally

(for

example,

when

the

float

activated

because

sudden

machine

movement),

resume

the

operation:

turn

off

the

vacuum

system

pressing

the

switch

(D,

Fig.

19),

then

open

the

cover

(C,

Fig.

22)

and

check

that

the

float

inside

the

grid

(A)

has

gone

down

the

water

level.

Then

the

cover

(C)

and

turn

the

vacuum

system

pressing

the

switch

(D,

Fig.

19).

When the recovery water tank (B, Fig. 21) is full, empty it

according to the following procedure.

Recovery

water

tank

emptying

Figure

Stop the machine.

Lift the brush/pad-holder deck (E, Fig. 21) by pressing the

pedal (F).

Lift the squeegee (G) with the lever (H).

Drive the machine to the appointed disposal area.

Empty the recovery water tank with the hose (I). Then, rinse

the tank (B, Fig. 22) with clean water.

Clarke Focus Boost

New

08/01/2013

Title

Revision

Date

Approved

Autres manuels pour FOCUS L17

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Clarke Machine de plancher

Clarke

Clarke C2K 13 Manuel utilisateur

Clarke

Clarke Focus II Manuel utilisateur

Clarke

Clarke C-5 Caractéristiques techniques

Clarke

Clarke BSW 28 Manuel utilisateur

Clarke

Clarke TFC 40056380773 Manuel utilisateur

Clarke

Clarke Encore S20E Manuel utilisateur

Clarke

Clarke 08001B Manuel utilisateur

Clarke

Clarke Vantage 17 Battery Manuel utilisateur

Clarke

Clarke American Sanders FA-807166A Manuel utilisateur

Clarke

Clarke Fusion 20 Manuel utilisateur

Clarke

Clarke CFP Pro 20DS Manuel utilisateur

Clarke

Clarke CA90 32T Manuel utilisateur

Clarke

Clarke CLARKE380B Manuel utilisateur

Clarke

Clarke RA40 Mode d’emploi

Clarke

Clarke FOCUS II MICRO RIDER 26D Manuel utilisateur

Clarke

Clarke FM-1700 HD Manuel utilisateur

Clarke

Clarke FOCUS II MICRO RIDER 26D Manuel utilisateur

Clarke

Clarke 59229A Instructions d'installation et d'entretien

Clarke

Clarke FOCUS II MICRO RIDER 26D Manuel utilisateur

Clarke

Clarke Vantage 17 cable Manuel utilisateur

Clarke

Clarke Clean Track 12 Manuel utilisateur

Clarke

Clarke US1500DC 01540A Manuel utilisateur

Clarke

Clarke Clean Track 12 Manuel utilisateur

Clarke

Clarke MA50 15B CLARKE380B Manuel utilisateur

Manuels Machine de plancher populaires d'autres marques

Nilfisk-Advance

Nilfisk-Advance Advance SC370 17B Manuel utilisateur

Numatic

Numatic ET 4045 Manuel utilisateur

HAWK ENTERPRISES

HAWK ENTERPRISES HP1513-180BRUTE Manuel utilisateur

Mytee

Mytee 8070 Mytee-Lite Manuel utilisateur

Kärcher

Kärcher B 140 R Manuel utilisateur

Triple S

Triple S Ace 26T1 Manuel utilisateur

Nilfisk-Advance

Nilfisk-Advance SW 750 Manuel utilisateur

Tornado

Tornado Marathon 2000 98190 Manuel

Windsor

Windsor ADMIRAL Admiral 8 Manuel utilisateur

Numatic

Numatic TTB 1117/100 Manuel utilisateur

Tennant

Tennant 8210D Manuel utilisateur

Nobles

Nobles Frontier Manuel du produit

lavina

lavina 21-X Manuel utilisateur

KENT

KENT Edge 28B Manuel utilisateur

Tennant

Tennant 215 Manuel du produit

Windsor

Windsor BDP 51/2000C Manuel utilisateur

CleanFreak

CleanFreak DURA-18HD Manuel utilisateur

Nilfisk-Advance

Nilfisk-Advance Warrior 34RST Guide de l'administrateur