claber 8063 Manuel utilisateur
CLABER AQUA-MAGIC SYSTEM 8063
DESCRIPTION:
Aqua-Magic System an independent drip kit. Can be used to water pots and small vegetable patches
selecting the water quantity and irrigation frequency by choosing from the preset values. Through its
photovoltaic panel, it uses solar energy to power the rechargeable batteries (not included).
1) Photovoltaic panel
2) Operating status LED
3) Water quantity dial
4) Irrigation frequency dial
5) Battery compartment
6) Water inlet
7) Water outlet
8) Wall bracket
9) Filter
10) Anti-siphon valve
11) Stakes
12) Tee coupling
13) End-of-line plug
14) Drippers
15) Feeding tube
16) Screws and plugs
INSERTING THE BATTERIES:
Use only 1.2 V NiMH AA/HR6 rechargeable batteries (1800 mAh or more). Please note that
rechargeable batteries tend to be almost flat when purchased. To recharge them, turn the dial to OFF
and expose the timer to direct sunlight for at least 8 hours. Alternatively, use an external battery charger
to charge them fully. Program it as required, making sure that the timer is always positioned correctly in
direct sunlight. Remove the batteries at the end of the season.
WARNINGS:
The timer works both horizontally and vertically (wall-mounted).
It must be installed in a place where the sunlight can reach it.
It must be positioned with the photovoltaic panel facing upwards.
It should not be positioned in a valve box.
It should not be immersed in liquid.
It should not be used by children or be easily reachable by pets.
The hoses should not be pulled.
In winter, the timer must be stored in a dry place where the temperature does not fall below 37°F.
INSTALLATION:
If the water tank is outside, position it in a shaded place. Fix the bracket to the wall using the screws
and plugs provided and hang the timer.
To install the water suction hose, cut a section of feeding hose, fit the filter at one end and connect the
other end to the timer in the outlet marked “IN”. To make the system work properly, the hose end with
the filter must touch the bottom of the water container. To do this, measure the “L” distance between the
timer and the bottom of the container, then cut the hose.
When setting up your system, we recommend respecting the distances shown between the timer, water
tank and hoses, so that the timer can function at its best.
Warning: the timer must be positioned between 6 - 118 inches above the water level.
After positioning the timer, the hoses, anti-siphon valve, stakes, fittings, drippers and end-of-line plugs
can be connected up.
Important: Use between 10 and 20 drippers. The drippers are not adjustable. The gray ring nut must
be fully screwed on, without being overtightened. Warning: Clean the drippers with running water or
immerse in water and vinegar.
See image for an example of how to connect up the system. The anti-siphon valve must be positioned
1 ½ - 2 inches from the inlet, on the hose connected to the “OUT” outlet.
LED STATUS DURING OPERATION:
● flashing quickly: the timer is being programmed
● flashing slowly: the timer is waiting to water or is watering
● yellow flash: batteries partially charged and insufficient sunlight to charge them
● red flash: batteries completely flat: if you use completely flat batteries the first time, once
inserted you will have to wait for the timer to recharge them before watering (approximately one
day in OFF mode).
LED off:
1) battery completely flat
2) programming not complete
3) “FREQUENCY” selector dial set to “OFF”
4) “FREQUENCY” selector dial set to manual when manual watering has finished.
PROGRAMMING:
How much to water (quantity per day per dripper in ml). At the time you want the watering to start, set
the water QUANTITY to be dispensed per day for each dripper by turning the “DRIPPER” selector dial
to the required value: the LED remains off, indicating that programming is not complete (the timer will
not water automatically until FREQUENCY). The quantities are preset and CANNOT be modified.
How often to water (watering frequency). Set the watering FREQUENCY by turning the “FREQUENCY”
selector dial: programming is complete, the LED flashes quickly for a few seconds, then SLOWLY (1
flash every 2 seconds). Once set, watering will begin immediately. Watering will finish when the quantity
of water set with the “DRIPPER” selector dial has been dispensed. The frequencies are preset and
CANNOT be modified.
When to water (at what time). At the time you want irrigation to start (e.g. 10 pm), insert the batteries
and turn the FREQUENCY dial. The first irrigation cycle will start straight away. The subsequent cycles
will start according to the program selected (e.g. 2 days).
SETTING CHANGES:
Changing start time and/or frequency of watering cycles. Set the “FREQUENCY” selector dial to “OFF”
and wait for the LED to switch off.
Wait for the new time at which you want watering to begin (for example 20:00). Set the “FREQUENCY”
selector dial to the frequency required. After resetting, watering will begin immediately for the set water
quantity: the next watering cycles will begin after the number of days set using the “FREQUENCY”
selector dial.
Changing the quantity of water dispensed. Increase or decrease the quantity set by turning the
“DRIPPER” selector dial; the change will take effect from the next watering cycle. If the operation is
carried out while watering is under way, watering will cease when the set quantity is reached (if the
quantity has been reduced) or it will continue (if the quantity has been increased) with immediate effect.
MANUAL WATERING:
Turn the FREQUENCY dial to manual 100 ml. The LED flashes during manual watering.
The run time of a manual irrigation session cannot be increased, but its end can be brought forward in
two ways: turn the “FREQUENCY” selector dial to the start position (e.g. 1 day). The previous
programming is stored, therefore the watering cycles will start at the normal times. When turning the
dial to the previous frequency, do not stop for more than 3 seconds on any other frequency as this will
be considered a new setting.
Early stop: Turn the “FREQUENCY” selector dial to a new frequency (e.g. 2 days). The previous setting
is NOT stored. An irrigation cycle will start straight away. The subsequent cycles will start according to
the new time and frequency selected.
If the “FREQUENCY” selector dial is set to manual and watering has finished, the LED remains off and
the timer will not water automatically until programmed again.
UNLOCKING THE PUMP:
Make sure that the batteries are charged and activate Aqua-Magic by turning the “FREQUENCY“ dial to
any program (to activate suction).
Table des matières
Autres manuels claber Système d'irrigation
claber
claber Tempo Hybrid Manuel utilisateur
claber
claber Aqua-Magic System Manuel utilisateur
claber
claber POP-UP Manuel utilisateur
claber
claber HYDRO-4 RF Manuel utilisateur
claber
claber POP-UP 0-350 Manuel utilisateur
claber
claber POP-UP 0-350 Manuel utilisateur
claber
claber 8053 Manuel utilisateur
claber
claber AQUAUNO MIST Manuel utilisateur
claber
claber POP-UP 90 Manuel utilisateur
claber
claber POP-UP Manuel utilisateur
Manuels Système d'irrigation populaires d'autres marques
Hunter
Hunter Institutional Series Manuel utilisateur
Cellfast
Cellfast 52-305 Manuel utilisateur
Tyco Fire Product
Tyco Fire Product Star Galaxy SGQR Manuel utilisateur
Tyco Fire Product
Tyco Fire Product CENTRAL A Manuel utilisateur
Oral Care Technologies
Oral Care Technologies Hydro Floss Manuel utilisateur
Reliable
Reliable F1-300 Manuel utilisateur
