CK Fires evonicfires TUVA Manuel
1
Stove Instrucon
Guide
Important Safety Informaon
Always read this manual rst before aempng to install or use this
replace. For your safety, always comply with all warnings and safety
Instrucons contained in this manual to prevent personal injury or property
damage.
Please Note: This product is for well insulated spaces or
occasional use.
English
Please Note: Once your stove has been installed and switched
to the ON posion, the re will take approximately 10 seconds
to power up. This is a normal operang procedure and NOT a
fault.
2
welcome to evonicres
evonicres is an award-winning brand of CK Fires Ltd, situated just outside Straord-
upon-Avon, we manufacture a range of Brish built electric res and are considered as
one of the most technically advanced manufacturers in the world, with oponal
controllers such as e-touch and a fully integrated APP available to download on both
or .
This guide is designed to aid in the installaon and connued performance of this
product. This product conforms with all health, safety, and environmental protecon
standards as indicated by a CE mark. For opmum performance this product requires
a well insulated locaon or occasional use.
1. Electrical Safety (3/4
2. Important Instrucons (5
3. Installaon Requirements &
Specicaon (6
4. Switch Idencaon (7-9
5. Glass Removal (10-12
6. Log Set Guidance (13
7. E-smart App Template (14
8. Problem Solving Chart (15/18
9. Warranty Informaon (19
Contents
3
ELECTRICAL SAFETY:
When using electrical appliances, basic precauons should always be
followed to reduce the risk of re, electric shock, and injury to persons,
including the following:
① Read all instrucons before using this electric replace.
② This replace is hot when in use. To avoid burns, do not let bare skin
touch hot surfaces. The trim around the heater outlet becomes hot during
heater operaon. DANGER: High temperatures may be generated under
certain abnormal condions. Do not parally or fully cover or obstruct the
front of this heater.
③ Extreme cauon is necessary when any heater is used by or near children
or people of reduced mobility and whenever the unit is le operang and
unaended.
④ Young children should be supervised to ensure that they do not play with
the appliance.
⑤ The appliance is not intended for use by young children or inrmed
persons without supervision.
⑥ In the event of a malfuncon, disconnect power at the service panel and
have the unit inspected by a reputable electrician before reusing.
⑦ If the supply cord is damaged, it must be replaced by the manufacturer,
or its service agent, or a qualied person in order to avoid a hazard.
⑧ Do not use outdoors.
⑨ Never locate replace where it may fall into a bathtub or other water
container.
⑩ To disconnect the replace, turn the controls o, and turn o power to
heater circuit at main disconnect panel.
⑪ Do not run the cord under carpeng. Do not cover cord with throw rugs,
runners, or the like. Arrange cord away from trac area and where it will not
be tripped over.
⑫ Do not locate the heater immediately below a xed socket-outlet.
4
⑬ Do not insert or allow foreign objects to enter any venlaon or
exhaust opening as this may cause an electric shock or re, or damage to
the heater.
⑭ To prevent a possible re, do not block air intakes or exhaust in any
manner.
⑮ All electrical heaters have hot and arcing or sparking parts inside. Do
not use in areas where gasoline, paint, or ammable liquids are used or
stored.
⑯ Use this replace only as described in this manual. Any other use not
recommended by the manufacturer may cause re, electric shock or
injury to persons.
⑰ Do not change the plug in any way. Always plug heaters directly into a
wall outlet/receptacle. Never use with an extension cord or relocatable
power tap (outlet/power strip).
⑱ Do not burn wood or other materials in the electric replace.
⑲ Do not strike the replace glass.
⑳ Always use a cered electrician should new circuits or outlets be
required.
㉑ Always use properly grounded, fused and polarized outlets.
㉒ Disconnect all power supply before performing any cleaning,
maintenance or relocaon of the unit.
㉓ When transporng or storing the unit and cord, keep in a dry place,
free from excessive vibraon and store so as to avoid damage.
NOTE: Changes or modicaons not expressly approved by the party
responsible for compliance could void user's authority to operate the
equipment.
5
IMPORTANT INSTRUCTIONS:
All Evonic brand products meet the requirements of EC direcves.
These direcves have been complied with by following the following standards:
EU 2011-65 / EU 2015/863 - Restricon of dangerous substances
EN 55014-1: 2006 + A2: 2011 Electromagnec compability.
EN 55014-2: 2015 Electromagnec compability.
EN 61000-3-2: 2014 Electromagnec Compability (EMC). Limits. Limits for harmonic power emissions
EN 61000-3-3: 2013 Electromagnec Compability (EMC). Limits. Limitaon of voltage changes, voltage
uctuaons and icker
EN 60335-1: 2012 + A1: 2014
EN 60335-2-30: 2009 + A11: 2012
Read through and carefully consider all of the following requirements before installaon:
This appliance may only be connected to 230/240 Volt AC 50 Hz.
Before connecng the unit, check that the supply voltage is in accordance with that indicated on the
electric stove. This appliance may only be connected to an AC outlet which is protected with
13 Amps.
The conductors in the power cord are colour labelled as for a standard UK socket:
GREEN / YELLOW - EARTH
BLUE - NEUTRAL
BROWN - CURRENT
Make sure that the power cord is not installed so that it is pinched or touches a sharp edge. To reduce the
risk of re, electric shock and personal injury, also ensure that the power cord is stored or aached in
such a way that no one can trip on or get stuck in it.
The electrical wiring and sockets installed in the building must comply with the local building regulaons
and other applicable regulaons to reduce the risk of re, electric shock and personal injury.
NOTE! These installaon requirements apply specically to the UK and dier between dierent countries
of origin.
6
INSTALLATION REQUIREMENTS:
If the product is to be installed into an open chimney or ue, it is important that the
chimney ue is blocked o to prevent any up/down draughts and falling debris
which could restrict the airow to the product.
It is also important to ensure that the product has a minimum clearance around it of
15mm, this is to ensure that the product can circulate the required airow to the
heater unit.
The product should never be sealed into an opening with the use of silicones or
adhesives as this can alter the airow and hinder any further servicing of the
product.
Please refer to technical specicaon table for further informaon, with reference
to measurements.
HEATER UNIT CUT OUT—This is a safety feature to safe guard against further
damage to the product.
If the airow is restricted the heater will automacally turn o. This can occur due to
incorrect installaon or obstrucon. To reset the heater funcon;
• Isolate from main power supply
• Leave product to cool
• Aer suitable cooling down period, remove the obstrucon if obstructed and
check installaon
• Aer 10 minutes the thermo switch (cut-out) in the heater will reset.
Please note that both the eect fan and heater fan omit a low decibel noise, both
of which are normal operang characteriscs.
Technical Specicaon
Servicing:
Only a competent person should service this appliance.
This appliance must be serviced every 12 months.
Warning: Before carrying out any repairs or servicing, ensure that the power supply cord
MODEL HEIGHT WIDTH DEPTH
TUVA 1015mm 493mm 342mm
HALMSTAD 825mm 865mm 328mm
HALDEN 1018MM 488MM 416MM
7
TUVA SWITCH IDENTIFICATION:
The on/o switch to acvate
connecon to your app or E-Tab
is located at the front of the re,
in the gap between the front
glass panel and the boom edge
of the frame, oset to the right
hand side. Fig 1.
Fig 1.
Your main power supply
is aached to the IEC
through the back of the
re. Fig 2.
Fig 2.
8
HALMSTAD SWITCH IDENTIFICATION:
The on/o switch to acvate
connecon to your app or E-Tab
is located at the front of the re,
in the gap between the front
glass panel and the boom edge
of the frame, oset to the right
hand side. Fig 1.
Your main power supply
is aached to the IEC
through the back of the
re. Fig 2.
Fig 1.
Fig 2.
9
HALDEN SWITCH IDENTIFICATION:
Your main power supply
is aached to the IEC
through the back of the
re. Fig 1.
The on/o switch to acvate
connecon to your app or E-Tab
is located on the underside of
the re, approximately 100mm
from the rear of the stove, o-
set to the right hand side. Fig 2.
Fig 2.
Fig 1.
10
TUVA GLASS REMOVAL:
To install the fuel set (Logs, decorave glass) the below steps must be taken
The front glass is held
in place by two
brackets, located at the
top and boom of the
re. Fig 1.
To remove the front glass,
start by idenfying the key
hole slots located in each
bracket. There are 2 in
each bracket, one on the
le and one on the right.
Fig 2.
Once you have found the key
hole slots, li the front glass
panel vercally, then
towards you to release the
brackets. Fig 3.
Fig 1.
Fig 2.
Fig 3.
Ce manuel convient aux modèles suivants
2
Table des matières
Manuels Poêle populaires d'autres marques
Vermont Castings
Vermont Castings Intrepid 2 Manuel utilisateur
Italiana Camini
Italiana Camini CLASSICA Guide de démarrage rapide
Avalon
Avalon Vashon Avanti DVS FS Manuel utilisateur
Spartherm
Spartherm ambiente a1 Manuel utilisateur
Dimplex
Dimplex MCFSTV12AU Manuel utilisateur
Warmlite
Warmlite WL46040 Manuel utilisateur