Citronic MP16UHF Manuel utilisateur

MP16UHF 16-CHANNEL UHF

SYNTHESIZED WIRELESS

MICROPHONE DIVERSITY SYSTEM

171.329

Thank you for selecting our UHF PLL Synthesised Wireless System. Before

operation please read this instruction manual carefully in order to attain the

correct operating procedures and achieve the best results.

This UHF wireless receiver is with advanced PLL synthesised circuit which

can eliminate the random noise interference effectively when the receiver is

at standby state. The receiver has both balanced and unbalanced outputs

suitable for all amplifiers input.

This system includes the following accessories:

1. Audio Output Cable x 1 2. Instruction Manual x 1

3. Antenna x 2 4. AC/DCAdapter x 1

UHF PLL MULTI CHANNELS

WIRELESS MICROPHONE SYSTEM

1. RECEIVER PARTS DESCRIPTION

A. Front Panel

B. Rear Panel

(1) Antenna Input Connector.

(2) Power switch: When switch is turned on, LCD panel will light to indicate

normal power status.

(3) Channel selector.

(4) LCD panel: it displays channel no., frequency.

(5) Volume control.

(6) Balanced Audio Output Jack.

(7) Unbalanced Audio Output Jack.

(8) DC 15V Input Jack: To connect 15V DC from the AC/DC adapter.

1.Install antenna in rear (1). Extend antenna to the fullest position.

2.Power Input Connection:

Connect input connector of AC/DC adapter to power source. Connect

output connector to receiver rear panel DC input jack (8). Pay attention

to the power source voltage.

3.Audio Output Connection

(a) Unbalanced Output: Use attached audio cable to connect one end to

the unbalanced output jack (7) of the receiver. Connect the other end

to the "LINE-IN" input jack of amplifier.

(B) Balanced Output: Use "XLR" or "Cannon" type audio cable(not provided)

to connect one end to the balanced output jack (8)of the receiver. Connect

the other end to the "MIC IN" input jack of the mixer or amplifier.

2. INSTALLATION OF THE RECEIVER

1. Pull out antenna A & B. Make them to be perpendicular with the machine.

2. Connect input connector of AC/DC adapter to power source. Connect

output connector to receiver rear panel DC input jack (8).

Make sure the power source voltage is same as marked voltage on the

rear panel

3. Connect one end of attached audio cable to the unbalanced output jack(7)

of the receiver. Connect the other end of the cable to "line in" input jack of

amplifier.

4. Turn on power switch, LCD panel will light.

5. Press UP or down button to set the receiver frequency same as transmitter

frequency.

6. Turn on transmitter power switch, "RF" indicator of the receiver will display

Volume of the receiver can be controlled by adjusting the volume knob.

Attention

When installing the receiver, locate the receiver at least 1m above the ground

and 1m beyond the wall. Antennae should be extended fully to get the

the reception signal.

3.OPERATION OF THE RECEIVER

4. TRANSMITTER PARTS DESCRIPTION

1. MIC head: capsule inside.

2. Power switch

3. LCD Display: display channel no., Frequency and battery life.

4. Channel Selector

5. Colorful ring. It is for distinguishing different microphones.

6. Battery compartment.

6. OPERATION OF THE TRANSMITTER

1. Unscrew the battery compartment then put in a 9V battery.

Attention: The polarity should be right.

2.Turn on the transmitter. LCD panel will light. If LCD panel does not light,

check the battery to see if the voltage is low or the battery is not installed

correctly.

3. Press Up or Down to adjust frequency.

5. OPTIONAL TRANSMITTER/HEADSET MIC (171.335)

FREQUENCY & CHANNEL LISTING

Channel 01 = 863.350MHz

Channel 02 = 863.450MHz

Channel 03 = 863.550MHz

Channel 04 = 863.650MHz

Channel 05 = 863.750MHz

Channel 06 = 863.850MHz

Channel 07 = 863.950MHz

Channel 08 = 864.150MHz

Channel 09 = 864.250MHz

Channel 10 = 864.350MHz

Channel 11 = 864.450MHz

Channel 12 = 864.550MHz

Channel 13 = 864.650MHz

Channel 14 = 864.750MHz

Channel 15 = 864.850MHz

Channel 16 = 864.950MHz

6. TROUBLESHOOTING

7.SPECIFICATION

1. Turn on the receiver, but the indicator does not light.

-Make sure the power cable is well fixed and the socket is in good condition.

-Check if the fuse is blown.

2. When you speak, the "AF" light twinkles but no sound output.

-Check if the volume is in lowest place or the audio cable is not fixed well.

3. The effective signal-receiving distance becomes close. And signal-receiving

is not well. Sound quality is bad.

-Check if the battery power is low. Change new battery.

-Check if there are same frequency signals in your surroundings.

* Do not use two units with the same frequency at the same time in a place.

(Separate them at least 120m.)

* Do not open and repair it when some serious breakdown happens.

* Please contact your local distributor for repair.

1.COMPREHENSIVE PERFORMANCE

2.RECEIVER

POWER SUPPLY: DC15V

CONSUME POWER: 5 WATER

SIGNAL/NOISE RATIO: MORE THAN 90dB

IMAGE & SPURIOUS REJECTION: MORE THAN 80dB

BORDER UPON CHANNEL REJECTION: MORE THAN 80dB

RECEIVING SENSITIVITY: LESS THAN 10dBu V(SINAD=30dB)

DE-EMPHASIS: 50µs

CARRIER FREQUENCY: UHF 863-865MHz

FREQUENCY STABILISATION: < 30ppm

DYNAMIC RANGE: MORE THAN 90dB

TOTAL HARMONIC DISTORTION: LESS THAN 0.5%

FREQUENCY RESPONSE: 40HZ-15KHZ 3dB

AUDIO OUTPUT LEVEL: UNBALANCED OUT: 0-- 400mV

BALANCED OUT: 0-- 200mV

3.TRASNMITTER

8. IMPORTANT SAFEGUARDS

TRANSMITTING POWER: 8.5mW

MODULATION TYPE: FM, F3F

MAX DEVIATION: 25kHz

SPURIOUS EMISSION: >40dB (WITH CARRIER)

POWER SUPPLY: 9V battery

BATTERY LIFE: 6 hours (GP) 1604s 9V battery

NOISE CONTROL: perfect circuit for eliminating noise

1.The installation of receiver antenna influences the operating efficiency

of the receiver. Place receiver and microphone as short as possible for

better reception and performance.

2.The external DC power supply should not be below 12V. Otherwise it

would not work properly. If it is over 15V, some components of the

receiver will be damaged due to higher current. Use minimum 1A

power supply.

9. CAUTION

1.Avoid putting the main machine in a blind angle when it is used. This is to

keep signal reception in good condition.

2.Don't throw, fall, toss, cast the handheld microphone so as not to damage

it seriously.

3.Please keep the machine from direct sunshine or rains. Place it in a place

far away from the magnetic field.

4.Don't open it yourself because there is high voltage in it.

Table des matières

Autres manuels Citronic Système de microphone

Citronic

Citronic 171.972UK Manuel utilisateur

Citronic

Citronic RU105 Manuel utilisateur

Citronic

Citronic LM58-T Manuel utilisateur

Citronic

Citronic 171.970UK Manuel utilisateur

Citronic

Citronic MU16 Manuel utilisateur

Citronic

Citronic MU16H Manuel utilisateur

Citronic

Citronic CU-50 Manuel utilisateur

Citronic

Citronic RU26H Manuel utilisateur

Citronic

Citronic ru210 Manuel utilisateur

Manuels Système de microphone populaires d'autres marques

Paso

Paso R824 Manuel utilisateur

Naxa

Naxa NAM-982 Manuel utilisateur

Motorola

Motorola PMNN4461 Manuel utilisateur

Xvive

Xvive U3 Manuel utilisateur

Tekon

Tekon DUOS Manuel utilisateur

Heyuan Intelligence

Heyuan Intelligence IOT-G2S-01 Manuel utilisateur

Devine

Devine WMD-IE Manuel utilisateur

LG LF-D7150 Manuel utilisateur

GE S768DAV Manuel utilisateur

LD U305 HBH 2 Manuel utilisateur

Chainway

Chainway URA8 Manuel utilisateur

ORATOR

ORATOR D860TD Manuel utilisateur

Sennheiser

Sennheiser Evolution Wireless Digital EW-DX EM 2 Manuel utilisateur

Alpha Technologies

Alpha Technologies RBMS Manuel utilisateur

SWIT Electronics Co.,LTD.

SWIT Electronics Co.,LTD. CW-S150 Manuel utilisateur

Shure

Shure UA844 Manuel utilisateur

Panasonic

Panasonic SHFX70 - DVD HOME THEATER WIRELESS SYSTEM Manuel utilisateur

Pyle

Pyle PDWM5000 Manuel utilisateur