Citizen CMP-20 Manuel utilisateur

MOBILE THERMAL PRINTER

MODEL CMP-20 series

Technical Manual

Rev. 1.00

- 2 -

TABLE OF CONTENTS

1. General Specifications

1.1 Printing Specifications

1.2 Character Specifications

1.3 Paper Specification

1.4 Printable Area

1.5 Internal Buffer

1.6 Electrical Characteristics

1.7 EMI and Safety Standards Applied

1.8 Reliability

1.9 Environmental Conditions

2. Configuration

2.1 RS-232 serial interface

2.1.1 Specifications

2.1.2 Switching between on-line and off-line

2.1.3 Interface connector terminal assignments and signal functions

2.1.4 Serial interface connection example

2.2 USB Interface

2.3 Bluetooth Interface

2.4 WiFi Interface

2.5 Interface Connector

3. Connectors

3.1 MSR

3.2 IC-CARD

4. Control Command Summary

- 3 -

1. General Specifications

1.1 Printing Specifications

1) Printing method: Thermal line printing

2) Dot density: 203dpi

3) Printing direction: Unidirectional with friction feed

4) Printing width: 48mm(1.88"), 384 dot positions (203dpi)

5) Characters per line(ESC Emulation): Font A: 32

Font B: 42

6) Printing speed: 80mm/second maximum

☞NOTE: Speeds are switched depending on the applied voltage to the printer and head

temperature conditions automatically.

☞NOTE: There may be variations in printing after switching the mode of the printing

speed. To prevent this for logo printing with ESC* command, using a

downloaded bit image is recommended. Change in printing speed does not

occur during downloaded bit image printing.

7) Line spacing (default): 1/6 inch (4.23mm)

Programmable by control command.

- 4 -

1.2 Character Specifications

1) Number of characters: Alphanumeric characters: 95

Extended graphics 128 × 18 pages

(including one space page)

International characters: 14

① English

② Hangul

③ Chinese (GB2312,Big5)

④ Kanji

2) Character structure: Font A: 12 ⅹ24

Font B: 9 ⅹ17

Hangul, Chinese: 24 ⅹ24

Font A is selected as the default

3) Character size:

EPSON Emulation

1)Dot density 0.125ⅹ0.125mm/dot (203*203dpi)

[dpi: dots per 25.4mm{1"}]

2)Printing direction Unidirectional With friction feed

3)Paper width

58.5mm(2.28")

4)Maximumprintable area

48mm(384dots)

5)Character / line

Font A (12ⅹ24) 32

Font B (9ⅹ17) 42

Kanji Font (24ⅹ24) 16

1.3 Paper Specification

1) Paper type: Specified thermal paper

2) Form: Paper roll

3) Paper width: 58 ±0.5mm (2.28" ±0.02")

4) Paper roll size: Roll diameter : Maximum 48mm

5) Paper roll spool diameter: Inside: 12mm(.47")

Outside: 18mm(.71")

☞NOTE: Paper must not be pasted to the paper roll spool.

- 5 -

1.4 Printable Area

1.5 Internal Buffer

1) Receive buffer: 4Kbyte

1.6 Electrical Characteristics

1) Supply voltage: +7.4VDC , 1800mAH Li-ion Battery

2) Current consumption :

Operating:Approx.1.5A(atASCIIPrinting)

Peak:Approx. 4A(at print duty 100%, For 10 seconds or less)

Stand-by: Approx. 0.1A

1.7 EMI and Safety Standards Applied

1) UL: Safety – EN 60950-1:2001+A11:2003

EMS – EN55022:98+A1:2000+A2:2003

– EN55024:98+A1:2001+A2:2003

– EN301 489-1 V1.6.1

– EN301 489-17 V1.2.1

RF – EN 300 328 V1.7.1(2006-10)

1.8 Reliability

1) MCBF: 50 million lines

(based on an average printing rate of 12.5% with paper thickness in the

range 65 ㎛to 75 ㎛).

1.9 Environmental Conditions

1) Temperature: Operating: 5°to 45°C

Storage: -20°to 60°C

(except for paper)

2) Humidity: Operating: 10 to 90%RH

Storage: 10 to 90%RH (except for paper)

- 6 -

2. Configuration

2.1 RS-232 serial interface

2.1.1 Specifications

Data transmission: Serial

Synchronization: Asynchronous

Handshaking: DTR/DSR or XON/XOFF control

Signal levels: MARK= -3 to –15V: Logic “1”

SPACE= +3 to +15V: Logic “0”

Baud rage: 4800, 9600, 19200, 38400,57600,115200 bps

Data word length: 7 or 8 bits

Parity Settings: None, even, odd

Stop bits: 1 or more

Connector (printer side): Female DSUB-25 pin connector

☞NOTE: The data word length, baud rate, and parity depend on the

Software-Tool settings.

2.1.2 Switching between on-line and off-line

The printer does not have an on-line/off-line switch.

The printer goes off-line:

•Between when the power is turned on (including reset using the interface)

•During the self-test.

•When the cover is open.

•During paper feeding using the paper feed button.

•During macro executing stand by status.

•When a temporary abnormality occurs in the power supply voltage.

•When an error has occurred.

2.1.3 Interface connector terminal assignments and signal functions

PIN SIGNAL I/O DESCRIPTION

1 RXD - Printer receive data line RS-232C level

2 TXD - Printer transmit data line RS-232C level

3 DTR Output Printer handshake to host line RS-232C level

4,5,6,7,8 GND - System Ground

- 7 -

2.1.4 Serial interface connection example

Host side Printer side

TXD ………………………………… RXD

DSR ………………………………… DTR

RXD ………………………………… TXD

FG ………………………………… FG

SG ………………………………… SG

DETAILS: ◦Set the handshaking so that the transmit data can be received.

◦Transmit data to the printer after turning on the power and initializing

the printer.

< Figure 2.1 Serial transmission bit frame >

< Figure 2.2 Line transmission with protocol >

ready busy ready busy

buffer full buffer emptied

"1"

"0"

"1"

RxD

DTR

B0 B1 B2 B3 B4 B5 B6 B7START PARITY

"1"

"0"

STOP

1Bit

7 or 8

one or

1 Bi

1 or 2

Bit

- 8 -

2.2 USB Interface

PIN SIGNAL I/O DESCRIPTION

1 +5V - +5V

2 DATA- - Printer transmit data line

3 DATA+ - Printer transmit data line

4 GND - System Ground

1) Specifications

Data transmission: USB 2.0

Connector: USB “B” type connector

2) USB interface connection example

Host side Printer side

VCC ………………………………… VCC

DATA+ ……………………………… DATA+

DATA- ……………………………… DATA-

GND ………………………………… GND

2.3 Bluetooth Interface (Option)

1) The printer can be connected to devices equipped Bluetooth communication capacity

(PDA, PC, etc…)

2) Use the Bluetooth connection function suppoeted by the device to connect to the printer

Classifications Description

Bluetooth Spec. Bluetooth V2.0 / Class2(10m)

Frequency 2.4GHz ISM BAND

Modulation method

FH method

(Frequency hopping spectrum diffusion method)

Hypothetical

interference distance

10m

Transfer rate

The communication speed between Bluetooth and the

printer is 115.2kbps.

Data bit / Parity bit /

Stop bit

8 Data bit / Noparity / 1 Stop bit Fixed.

Transfer capacity Up to +4 dBm (class 2)

PIN code “0000” Fixed.

Profile Serial Port Profile (SPP)

- 9 -

2.4 Wifi Interface ( Factory Option )

Item Content

Standard 802.11b, 802.11g

Communication Speed(Max) 54M

Transmission Distance(Max)

100m(Indoors without obstructs))the

distance Depending on

the environment)

chanel 1-14

Wireless

Safety 64/128 WEP, WPA

Condition’s monitor

Special configure tools

Browser

Configuration management

Special configure tools

Browser

Firmware updating TFTP

Basic communication protocol ARP, RARP, IP, ICMP, TCP, UDP

The

interface

module

Printing communication mode Port 9100, LPR/LPD

State demand

The Software package

(include DLL and Routines), browser

Average communication speed >50kByte/s

2.5 Interface Connector

- 10 -

3. Module Configuration

3.1 MSR Item Content

Card Standard ISO 7811/2, JIS

Dual Track 1 , 2 Track or 2 ,3 Track

CardSwipe Speed 10cm ~ 15cm / sec (4 ~ 6 inch/sec)

Magnetic Head Life 300,000passes (minimum)

Power Consumption(3.0VDC)

Standard : 3mA(Dual)

Operation : 500~900uA(Dual)

Reading Track Width 1.5mm

Operation Temperature and Humidity -20℃~ +60℃, 20% ~ 90% RH

Conservation Temperature and Humidity -35℃~ +75℃, Less than RH

3.2 IC-CARD

Item Content

Host Interface -Default Baud Rate : 9,600bps

Card Interface - Internal 1Ch(Default)

Ambient operating Temperature 0℃to +70℃

Power supply Voltage range 4.7V to 5.5V

Input High Voltage RST,XTAL1

0.7Vcc Min

Vcc+0.5Max

Input Low Voltage

-0.5V Min

0.2Vcc – 0.1Max

Output Card Supply Voltage 2.75V < < 3.25V (CRD_Vcc = 3V)

Output Card Current Limit Time Out 4mS Typ.

Output Card Over current Limit 100mA MAX.

Autres manuels pour CMP-20

Table des matières

Autres manuels Citizen Imprimante

Citizen

Citizen CL-E700 Series Manuel utilisateur

Citizen

Citizen CT-S300 Manuel utilisateur

Citizen

Citizen CBM-272 Manuel utilisateur

Citizen

Citizen CTS751XNEWX Manuel utilisateur

Citizen

Citizen Mini Printer Manuel utilisateur

Citizen

Citizen CMP-20 Manuel de service

Citizen

Citizen PPU-700 Manuel utilisateur

Citizen

Citizen CBM1000II RF Manuel d'installation

Citizen

Citizen CD-S500 series Manuel utilisateur

Citizen

Citizen CT-S4000 Manuel utilisateur

Citizen

Citizen iDP-3210 Manuel utilisateur

Citizen

Citizen LINE THERMAL PRINTER CT-S280 Manuel utilisateur

Citizen

Citizen iDP3540 Series Manuel utilisateur

Citizen

Citizen CTS801IIN3NEBPXX Manuel utilisateur

Citizen

Citizen CT-S801 II Manuel utilisateur

Citizen

Citizen CBM-920 Manuel utilisateur

Citizen

Citizen CLP-512 Manuel utilisateur

Citizen

Citizen CT-S851 Manuel utilisateur

Citizen

Citizen CBM-710 Manuel utilisateur

Citizen

Citizen iDP-3550 Manuel utilisateur

Citizen

Citizen iDP-3221 Series Manuel utilisateur

Citizen

Citizen CT-D150 Manuel d'installation

Citizen

Citizen CBM-270 Manuel utilisateur

Citizen

Citizen CLP-7401 Manuel utilisateur

Manuels Imprimante populaires d'autres marques

Lexmark

Lexmark 1400 Series Manuel

Canon

Canon i70 Series Manuel utilisateur

Evolis

Evolis Elypso Manuel utilisateur

Kyocera

Kyocera FS-9530DN Manuel utilisateur

Canon

Canon LASER SHOT LBP-1210 Manuel utilisateur

Samsung

Samsung BIXOLON SRP-350plusF Manuel utilisateur

Canon

Canon PIXMA PRO-1 Series Manuel utilisateur

Canon

Canon PIXMA G3560 Guide de configuration

Dell

Dell Color Laser Printer 2130cn Manuel utilisateur

Tektronix

Tektronix Phaser 840 Manuel utilisateur

Epson

Epson ET-7750 Mode d'emploi

Canon

Canon CLBR 460ps Manuel utilisateur

Eltron

Eltron P210 Guide Manuel utilisateur

Ricoh

Ricoh MD-P1 Manuel utilisateur

Epson

Epson SC-F7100 series Manuel utilisateur

Epson

Epson Stylus C40UX Manuel utilisateur

Canon

Canon imagePASS-A2 Manuel utilisateur

Canon

Canon S820D Manuel utilisateur