Cisco Nexus 5000 Series Manuel utilisateur

CHAPTER

Send document comments to nexus5k-docfeedbac[email protected].

1-1

Cisco Nexus 5000 Series Troubleshooting Guide

OL-25300-01

Troubleshooting System Management Issues

The system management features of the Cisco Nexus 5000 Series switch allow you to monitor and

manage your network for efficient device use, role-based access control, SNMP communications,

diagnostics, and logging.

This chapter describes how to identify and resolve problems that can occur with system management and

the Cisco Nexus 5000 Series switch.

This chapter includes the following sections:

•SNMP

•Logging

•CPU Processes

•Traps

•DNS

SNMP

SNMP memory usage continuously increasing

The show proc mem | inc snmp command shows continuously increasing SNMP memory usage.

Possible Cause

SNMP memory usage increases when SNMP requests are processed from different monitoring stations.

Typically, this situation stabilizes over time. If the memory increases continuously without stabilizing,

then some of the SNMP requests are causing a memory leak.

Solution

Review the output from the show system internal snmp mem-stats detail command.

Take example snapshots with the following commands while processing SNMP requests:

•show clock

•show system internal mem-stats detail

•show tech snmp

Send document comments to nexus5k-docfeedbac[email protected].

1-2

Cisco Nexus 5000 Series Troubleshooting Guide

OL-25300-01

Chapter 1 Troubleshooting System Management Issues

SNMP

SNMP not responding

No response or delayed response for SNMP request.

Possible Cause

If the switch CPU utilization is high during the SNMP operations such as GET, GETNEXT and WALK,

the response may be very slow or there is no responsethat results in a time-out.

Solution

While SNMP is not responding, check CPU utilization with the following commands:

•show proc cpu history

•show proc cpu sort

The output from this command shows which Nexus 5000 component is using the greatest amount of

CPU resources.

SNMP not responding and show snmp command reports SNMP has timed out

SNMP is not responding and the show snmp command reports that SNMP has timed out.

Possible Cause

The SNMP process might have exited, but the process did not crash.

Solution

Use show system internal sysmgr service name snmpd command which should show the state to

be“SRV_STATE_HANDSHAKED.

Example:

Service "snmpd" ("snmpd", 74):

UUID = 0x1A, PID = 4131, SAP = 28

State: SRV_STATE_HANDSHAKED (entered at time Mon Jun 14 17:12:15 2010).

Restart count: 1

Time of last restart: Mon Jun 14 17:12:14 2010.

The service never crashed since the last reboot.

Tag = N/A

Plugin ID: 0

Not able to perform SNMP SET operation

The following error appears when trying to perform the SNMP SET operation:

bash-2.05b$ snmpset -v2c -c private 10.78.25.211 .1.3.6.1.4.1.9.9.305.1.1.6.0 i 1

Error in packet.

Reason: notWritable

Possible Cause

The SNMP community does not have write permission.

Solution

Check the output of the show snmp community command to ensure that the write permission is enabled.

Example:

Community Group / Access context acl_filter

Send document comments to nexus5k-docfeedbac[email protected].

1-3

Cisco Nexus 5000 Series Troubleshooting Guide

OL-25300-01

Chapter 1 Troubleshooting System Management Issues

Logging

private network-operator

public network-admin

Only “network-admin” has write permissions.

snmpset -v2c -c public 10.78.25.211 .1.3.6.1.4.1.9.9.305.1.1.6.0 i 1

enterprises.9.9.305.1.1.6.0 =

SNMP on BRIDGE-MIB

The SNMP GET on BRIDGE-MIB operation does not return correct values and results in errors.

Possible Cause

The BRIDGE-MIB may not be supported.

Solution

Check the release notes to make sure that BRIDGE-MIB is supported on NX-OS Release 4.2(1) or later

releases.

Logging

System is not responsive

System performance is significantly slower or non responsive.

Possible Cause

Some system resources may be over-utilized. For example, an incorrect logging level might generate

many messages resulting in an impact on system resources.

Solution

Check the logging level on the chassis. If you have a logging level setting, such as 6 or 7, many messages

are generated and performance can be impacted. Use the following commands to display the amount of

resources that are being used.

•show proc cpu | inc syslogd

•show proc cpu

•show run | inc logging

•show system resource

Syslog server not getting messages from DUT

Although the syslog server is configured, the destination syslog server is not receiving messages from

DUT.

Possible Cause

Syslog server might not be accessible or the logging level might not be appropriate.

Solution

Send document comments to nexus5k-docfeedbac[email protected].

1-4

Cisco Nexus 5000 Series Troubleshooting Guide

OL-25300-01

Chapter 1 Troubleshooting System Management Issues

Logging

•Check to see if the destination syslog server is accessible from VRF management. Use the ping

<dest-ip> vrf management command to ping the server.

•Check that the syslog configuration on the DUT has use-vrf management.

Example:

logging server 10.193.12.1 5 use-vrf management

•Check that the appropriate logging level is enabled to send logging messages. Use the show logging

info command. If the logging level is not appropriate, then set the appropriate level using the

logging level <feature> <log-level> command.

Send document comments to nexus5k-docfeedbac[email protected].

1-5

Cisco Nexus 5000 Series Troubleshooting Guide

OL-25300-01

Chapter 1 Troubleshooting System Management Issues

CPU Processes

High CPU Utilization

CPU experiences brief high utilization.

Possible Cause

Brief high utilization caused by CPU multitasking.

Solution

Spikes of high CPU utilization on the Cisco Nexus 5000/5500 switch is normal activity.

The show system resources command displays the high level CPU utilization for the supervisor module.

The show process cpu command with the sort option displays all of the processes sorted by the highest

CPU utilization per process. The show process cpu history command displays the CPU history in three

increments: 60 seconds, 60 minutes, 72 hours. Viewing the CPU history is valuable when correlating a

network event with the past CPU utilization.

Cisco NX-OS takes advantage of preemptive CPU multitasking, so processes can take advantage of an

idle CPU to complete tasks faster. Therefore the show process cpu history command might display CPU

spikes that are not necessarily a problem. Additional investigation is required if the average CPU remains

close to 100%.

Example:

switch# show processes cpu sort

PID Runtime(ms) Invoked uSecs 1Sec Process

----- ----------- -------- ----- ------ -----------

3611 57354660 30766347 1864 7.0% statsclient

4011 110298193 27004447 4084 5.3% fcpc

3561 96792384 87683659 1103 3.5% gatosusd

3685 862 8678 99 1.8% netstack

1 39116 447596 87 0.0% init

switch# show processes cpu history

41 11 11111111131 11 11 1 12811111121 11 1122 1111111 1

808008808093532901815792389618988723121180936746257022006081

100

90 #

80 #

70 #

60 #

50 # #

40 # #

30 # # ## # #

20 # # # # ## # ### # # ### #

10 ############################################################

0....5....1....1....2....2....3....3....4....4....5....5....

0 5 0 5 0 5 0 5 0 5

Send document comments to nexus5k-docfeedbac[email protected].

1-6

Cisco Nexus 5000 Series Troubleshooting Guide

OL-25300-01

Chapter 1 Troubleshooting System Management Issues

Traps

Traps not received

The results of traps are not received.

Possible Cause

The traps might not be enabled or the SNMP host might not be accessible.

The following are possible causes:

•Traps might not be enabled.

•The SNMP host might not be accessible.

•A firewall might be blocking access.

•An access list might be blocking UDP port 162.

Solution

Use the following commands to check whether the proper VRF is configured for the SNMP host and that

the trap is enabled:

•snmp-server enable traps <trapname>

•snmp-server host <x.x.x.x> use-vrf <vrf-name>

where x.x.x.x is the IP address of the trap receiving device.

DNS

DNS resolution not working correctly

When specifying a host name using DNS or VRF, the host name is not resolved and an error occurs.

Possible Cause

The DNS client is not configured correctly.

Solution

Use the following commands to configure the DNS client:

•config t

•vrf context management

•ip host name <address1 [address2... address6]>

•ip domain-name name [use-vrf <vrf-name>]

•ip domain-list name [use-vrf <vrf-name>]

•ip name-server <server-address1 [server-address2... server-address6]>< [use-vrf vrf-name>]

•ip domain lookup

•show hosts

•copy running-config startup-config

Send document comments to nexus5k-docfeedbac[email protected].

1-7

Cisco Nexus 5000 Series Troubleshooting Guide

OL-25300-01

Chapter 1 Troubleshooting System Management Issues

DNS

Specified domain not removed from domain-list

When using the no ip domain-list <name> command to remove a specified domain from the

domain-list, only the most recently added domain is removed.

Possible Cause

The no ip domain-list <name> command is not locating the specified domain.

Solution

There are two possible workarounds:

•To remove a domain using the no ip domain-list <name> command that is not the most recently

added domain to the domain-list, you must temporarily remove every domain in the domain-list until

reaching the desired domain. Then you must add back the temporarily removed domains to the

domain-list.

•An alternative approach is to copy the startup-config and delete the desired domain with a text editor.

Then you must load the edited startup-config back onto the device.

Send document comments to nexus5k-docfeedbac[email protected].

1-8

Cisco Nexus 5000 Series Troubleshooting Guide

OL-25300-01

Chapter 1 Troubleshooting System Management Issues

DNS

Autres manuels pour Nexus 5000 Series

Table des matières

Autres manuels Cisco Changer

Cisco

Cisco Nexus 93108TC-FX3P Manuel

Cisco

Cisco Catalyst 3850 series Manuel utilisateur

Cisco

Cisco Catalyst 3030 Manuel d'installation

Cisco

Cisco Nexus 7000 Series Manuel d'installation

Cisco

Cisco Small Business SF200-24 Mode d’emploi

Cisco

Cisco Catalyst Blade Switch 3130 Manuel utilisateur

Cisco

Cisco 1548 Instructions originales

Cisco

Cisco SLM2005 - Small Business Smart Switch Manuel utilisateur

Cisco

Cisco Catalyst 3560-CX Manuel utilisateur

Cisco

Cisco Nexus 5000 Series Manuel d'installation

Cisco

Cisco Catalyst X6748 Manuel utilisateur

Cisco

Cisco NCS 4200 Series Manuel utilisateur

Cisco

Cisco MDS 9120 - Fabric Switch Manuel utilisateur

Cisco

Cisco CSS 11801 Manuel utilisateur

Cisco

Cisco 500 Series Manuel utilisateur

Cisco

Cisco Catalyst X4232 Guide rapide

Cisco

Cisco Nexus 93360YC-FX2 Manuel

Cisco

Cisco Aironet 350 Series Manuel utilisateur

Cisco

Cisco Catalyst 2960 Series Manuel utilisateur

Cisco

Cisco SLM224G4PS Manuel utilisateur

Cisco

Cisco TOPSPIN SFS 3012 Instructions d'installation

Cisco

Cisco Catalyst 8500 Series Instructions originales

Cisco

Cisco Nexus 9332C Manuel

Cisco

Cisco Cisco mds 9216 - fabric switch Manuel

Manuels Changer populaires d'autres marques

URC

URC Total Control MFS-8 Manuel utilisateur

Azbil

Azbil HPQ-D11 Manuel utilisateur

Sony

Sony DFS-900M Manuel utilisateur

SICK

SICK i17S Manuel utilisateur

F&F

F&F SZR-277 Manuel utilisateur

Shure

Shure UAMS/BK Manuel utilisateur

Dräger

Dräger X-zone Switch Off Manuel utilisateur

Asco

Asco Joucomatic 349 Series Manuel utilisateur

BT Mini Hub Manuel utilisateur

D-Link

D-Link DES-1226G Manuel utilisateur

Johnson Controls

Johnson Controls FS80-C Manuel utilisateur

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manuel utilisateur

MicroNet

MicroNet SP1200A Manuel utilisateur

Ruijie

Ruijie RG-PF2920 Series Manuel d'installation et d'exploitation

Altinex

Altinex DA1914SX Manuel utilisateur

MiLAN

MiLAN MIL-SM2401M Manuel utilisateur

RJM

RJM MASTERMIND PBC/6X Manuel utilisateur

Atlas

Atlas MMK-KVM8 Manuel utilisateur