Cisco Edge 300 Series Manuel utilisateur

Americas Headquarters:

Cisco Systems, Inc., 170 West Tasman Drive, San Jose, CA 95134-1706 USA

Cisco Edge 300 Series Switch Installation Guide

•

About this Guide, page 1

•

Box Contents, page 2

•

Overview, page 3

•

Installing the Switch, page 6

•

Powering on the Switch, page 15

•

Resetting to Factory Mode, page 15

•

Technical Specifications, page 15

•

Regulatory Standards Compliance, page 16

•

EMC Class A Notices and Warnings, page 17

•

Declaration of Conformity for RF Exposure, page 17

•

Obtaining Documentation and Submitting a Service Request, page 19

About this Guide

This guide describes how to install the Cisco Edge 300 series switch on a wall or desktop and describes

the LEDs and ports.

For configuration information, see the Cisco Edge 300 series switch documentation on Cisco.com. For

system requirements, important notes, limitations, open and resolved bugs, and documentation updates,

see the release notes on Cisco.com.

Cisco Edge 300 Series Switch Installation Guide

OL-24909-02

Box Contents

Note

Verify that you have received these items. If any item is missing or damaged, contact your Cisco

representative or reseller.

1Cisco Edge 300 series switch 7Four M3.5 x 16-mm Phillips head tapping

screws

2Power adapter 8Four plastic drywall anchors

3Power cord 9Cable tie

1, 2

4Power cord retainer

1, 2

1. These parts are included in the wall-mount kit (ACC-E300-WALL).

2. These parts are included in the desktop kit (ACC-E300-DESK).

10 Desktop bracket

5Wall-mount bracket

11 Two M3.0 x 6-mm Phillips pan head screws

6Four M3.0 x 6-mm Phillips pan head screws

6 7 8

10 11 9

Cisco Edge 300 Series Switch Installation Guide

OL-24909-02

Overview

Figure 1 Cisco Edge 300 Series Switch — Front

Figure 2 Cisco Edge 300 Series Switch — Left

Figure 3 Cisco Edge 300 Series Switch — Rear

Table 1 Cisco Edge 300 Series Models

Model Description

CS-E300-AP-K9 Cisco Edge 300 series switch with WiFi and Bluetooth

CS-E300-K9 Cisco Edge 300 series switch

HS-E300-AP-K9

1. This model is available only in China.

HSJC/Cisco Edge 300 series switch with WiFi and Bluetooth

HS-E300-K9

HSJC/Cisco Edge 300 series switch

1USB ports 5Gigabit Ethernet (uplink) port

2HDMI port 6Ethernet (downlink) ports

3Audio out port 7Power

4Audio in port

POWER

1234

HDMI

255417

134 5 7

1USB port

255418

1Power button 2Reset button

255419

RESET

1 2

Cisco Edge 300 Series Switch Installation Guide

OL-24909-02

Overview

Port Descriptions

USB

There are four USB 2.0 Type-A ports. Each USB port can provide up to 5 W of power to a connected

device. You can connect a wired USB keyboard and mouse, a wireless USB receiver for a keyboard and

mouse, a USB camera, or a USB thumb drive.

HDMI

The HDMI port supports 1280x960 and 1024x768 (default) video output, and 720p and 1080p

high-definition video output.

Note

This product incorporates HDMI technology

HDMI, the HDMI Logo, and High-Definition Multimedia Interface are or registered trademarksregistered trademarks of HDMI Licensing LLC in

the United States and other countries.

Audio In

You can connect a microphone that uses a 3.5 mm connector.

Audio Out

You can connect headphones or external speakers that use a 3.5 mm connector.

Gigabit Ethernet

The Gigabit Ethernet uplink port provides a 10/100/1000 Mb/s connection to a Catalyst 2000 or

Catalyst 3000 series switch.

Ethernet

The Fast Ethernet ports provide 10/100 Mb/s connections to computers or other devices.

Cisco Edge 300 Series Switch Installation Guide

OL-24909-02

Overview

Wireless Features

WiFi

Supports 802.11b/g/n wireless clients.

Bluetooth

Supports Human Interaction Design Protocol (HIDP) for remote control or input devices.

LEDs

Figure 4 Cisco Edge 300 Series Switch LEDs

1Ethernet downlink 4Bluetooth

2Gigabit Ethernet uplink 5Power

3WiFi

1. Only CS-E300-AP-K9 and HS-E300-AP-K9.

255420

1234

12 3 4

13 4 5

Cisco Edge 300 Series Switch Installation Guide

OL-24909-02

Installing the Switch

You can install the switch on a wall by using the wall-mount bracket or install the switch on a desk or

table by using the desktop bracket. You can also install the switch in a ventilated cabinet using the

wall-mount or desktop bracket.

Equipment That You Need

•

Phillips screwdriver

•

Scratch awl or other sharp pointed object (wall-mount)

•

Electric drill with a 6-mm drill bit (wall-mount)

Ta b l e 2 L E D s

LED Color Meaning

Ethernet

downlink

Off No link.

Green Link present, no activity. Port is operating at 100 Mb/s.

Blinking green Activity. Port is sending or receiving data at 100 Mb/s.

Amber Link present, no activity. Port is operating at 10 Mb/s.

Blinking amber Activity. Port is sending or receiving data at 10 Mb/s.

Gigabit

Ethernet

Off No link.

Green Link up.

Blinking green Activity.

WiFi Off WiFi is disabled.

Green WiFi is enabled and functioning.

Blinking green WiFi is transmitting data.

Bluetooth Off Bluetooth is disabled.

Green Bluetooth is enabled and functioning.

Power Off There is no power or the self test has failed.

Green System is operating normally.

Blinking green System software is being upgraded.

Blinking amber System software download has failed.

Cisco Edge 300 Series Switch Installation Guide

OL-24909-02

Installing the Switch

Before You Begin

Before installing the switch, verify that these guidelines are met:

•

Front clearance so that the LEDs can be seen.

•

AC power cord reaches from the AC power outlet to the rear-panel connector.

•

Cabling is away from sources of electrical noise, such as radios, power lines, and fluorescent

lighting. Make sure that the cabling is safely away from other devices that might damage the cables.

•

Airflow around the switch is unrestricted.

•

Temperature around the unit does not exceed 104°F (40°C).

•

Humidity around the switch does not exceed 85 percent.

•

Altitude at the installation site is below 10,000 feet.

•

For Ethernet ports, cables from the switch to connected devices are not longer than 328 feet

(100 meters).

Warning Statements

Statement 1071

Statement 332

Warning

In order to comply with FCC radio frequency (RF) exposure limits, antennas should be located at a

minimum of 7.9 inches (20 cm) or more from the body of all persons.

Statement 332

Statement 1005

Warning

This product relies on the building’s installation for short-circuit (overcurrent) protection. Ensure that

the protective device is rated not greater than:

20A

Statement 1005

Warning

IMPORTANT SAFETY INSTRUCTIONS

This warning symbol means danger. You are in a situation that could cause bodily injury. Before you

work on any equipment, be aware of the hazards involved with electrical circuitry and be familiar

with standard practices for preventing accidents. Use the statement number provided at the end of

each warning to locate its translation in the translated safety warnings that accompanied this

device.

Statement 1071

SAVE THESE INSTRUCTIONS

Cisco Edge 300 Series Switch Installation Guide

OL-24909-02

Installing the Switch

Statement 1019

Warning

The plug-socket combination must be accessible at all times, because it serves as the main

disconnecting device.

Statement 1019

Statement 1030

Warning

Only trained and qualified personnel should be allowed to install, replace, or service this equipment.

Statement 1030

Statement 1040

Warning

Ultimate disposal of this product should be handled according to all national laws and regulations.

Statement 1040

Statement 1044

Warning

For connections outside the building where the equipment is installed, the following ports must be

connected through an approved network termination unit with integral circuit protection:

10/100/1000 Ethernet

Statement 1044

Statement 1047

Warning

To prevent the system from overheating, do not operate it in an area that exceeds the maximum

recommended ambient temperature of:

104°F (40°C)

Statement 1047

Statement 1074

Warning

Installation of the equipment must comply with local and national electrical codes.

Statement 1074

Statement 1076

Warning

To prevent airflow restriction, allow clearance around the ventilation openings to be at least:

3 inches (7.6 cm)

Statement 1076

Caution

Be aware of the size and weight of the switch when mounting. Ensure that the mounting location has a

stable flat surface and can safely support the weight of the switch.

Cisco Edge 300 Series Switch Installation Guide

OL-24909-02

Installing the Switch

Installing the Switch on a Wall

Statement 378

Warning

Read the wall-mounting instructions carefully before beginning installation. Failure to use the

correct hardware or to follow the correct procedures could result in a hazardous situation to people

and damage to the system.

Statement 378

You can mount the switch horizontally or vertically on a wall.

Note

The wall-mount bracket has four slots (in two pairs) on its bottom panel (see Figure 5).

Figure 5 Bracket Slot Distances for Wall-Mounting

14.17 inches (106 mm) 26.02 inches (153 mm)

255421

Cisco Edge 300 Series Switch Installation Guide

OL-24909-02

Installing the Switch

Step 1

Use the four M3.0 x 6-mm Phillips pan head screws to attach the wall-mount bracket to the bottom of

the switch (see Figure 6).

Figure 6 Attaching the Wall-Mount Bracket

Step 2

Connect all the cables that are necessary for your installation.

Step 3

Slide the power cord retainer along the power cord, and snap it into the chassis (see Figure 7).

1M3.0 x 6mm Phillips pan head screws

330223

Autres manuels pour Edge 300 Series

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Cisco Changer

Cisco

Cisco Nexus 9372PX Manuel utilisateur

Cisco

Cisco 300 Series Manuel utilisateur

Cisco

Cisco Nexus 5548P Manuel utilisateur

Cisco

Cisco Catalyst 3750E-48PD-F Manuel utilisateur

Cisco

Cisco MDS 9000 Series Manuel utilisateur

Cisco

Cisco Cisco mds 9124 - fabric switch Manuel de service

Cisco

Cisco VPN 3000 Manuel utilisateur

Cisco

Cisco Catalyst 3130 Manuel utilisateur

Cisco

Cisco SG 102-24 Manuel utilisateur

Cisco

Cisco Catalyst 2960S-24PD Manuel utilisateur

Cisco

Cisco Catalyst 2960 Series Manuel utilisateur

Cisco

Cisco Nexus 9396TX Manuel utilisateur

Cisco

Cisco ME 3400G-2CS - Ethernet Access Switch Manuel utilisateur

Cisco

Cisco ME 6500 Manuel utilisateur

Cisco

Cisco Catalyst 2360 Manuel utilisateur

Cisco

Cisco CSS 11501 - Content Services Switch Manuel utilisateur

Cisco

Cisco WS-C2350-48TD-S Manuel d'installation

Cisco

Cisco 2975 - Catalyst LAN Base Switch Manuel utilisateur

Cisco

Cisco Nexus 93360YC-FX2 Manuel

Cisco

Cisco 100 Series Manuel utilisateur

Cisco

Cisco 3750 - Catalyst EMI Switch Manuel d'installation

Cisco

Cisco 6260 Manuel utilisateur

Cisco

Cisco ISDN Link Manuel utilisateur

Cisco

Cisco CGS 2520 Manuel

Manuels Changer populaires d'autres marques

URC

URC Total Control MFS-8 Manuel utilisateur

Azbil

Azbil HPQ-D11 Manuel utilisateur

Sony

Sony DFS-900M Manuel utilisateur

SICK

SICK i17S Manuel utilisateur

F&F

F&F SZR-277 Manuel utilisateur

Shure

Shure UAMS/BK Manuel utilisateur

Dräger

Dräger X-zone Switch Off Manuel utilisateur

Asco

Asco Joucomatic 349 Series Manuel utilisateur

BT Mini Hub Manuel utilisateur

D-Link

D-Link DES-1226G Manuel utilisateur

Johnson Controls

Johnson Controls FS80-C Manuel utilisateur

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manuel utilisateur

MicroNet

MicroNet SP1200A Manuel utilisateur

Ruijie

Ruijie RG-PF2920 Series Manuel d'installation et d'exploitation

Altinex

Altinex DA1914SX Manuel utilisateur

MiLAN

MiLAN MIL-SM2401M Manuel utilisateur

RJM

RJM MASTERMIND PBC/6X Manuel utilisateur

Atlas

Atlas MMK-KVM8 Manuel utilisateur