Cisco Cisco mds 9216 - fabric switch Mode d’emploi

CHAPTER

Send documentation comments to [email protected].

3-1

Cisco MDS 9216 Switch Hardware Installation Guide

78-16165-01

Connecting the Cisco MDS 9216

Switch

The Cisco MDS 9216 Switch provides the following types of ports:

•CONSOLE port (Interface Module): An RS-232 port that you can use to

create a local management connection.

•COM1 port (Interface Module): An RS-232 port that you can use to connect

to an external serial communication device such as a modem.

•MGMT 10/100 Ethernet port (Interface Module): An Ethernet port that you

can use to access and manage the switch by IP address, such as through the

CLI or Fabric Manager.

•Fibre Channel ports (Supervisor and Switching Modules): Fibre Channel

ports that you can use to connect to the SAN, or for in-band management.

Caution When running power and data cables in overhead or sub-floor cable trays, we

strongly recommend that power cables and other potential noise sources be

located as far away as practical from network cabling that terminates on Cisco

equipment. In situations where long parallel cable runs cannot be separated by at

least 3.3 ft (1 m), we recommend shielding any potential noise sources by housing

them in a grounded metallic conduit.

Send documentation comments to [email protected].

Chapter 3 Connecting the Cisco MDS 9216 Switch

Preparing for Network Connections

3-2

Cisco MDS 9216 Switch Hardware Installation Guide 78-16165-01

This chapter provides the following information:

•Preparing for Network Connections, page 3-2

•Connecting to the Console Port, page 3-2

•Connecting to the COM1 Port, page 3-4

•Connecting to the MGMT 10/100 Ethernet Port, page 3-6

•Connecting to a Fibre Channel Port, page 3-7

Preparing for Network Connections

When preparing your site for network connections to the Cisco MDS 9216

Switch, consider the following for each type of interface, and gather all the

required equipment before connecting the ports:

•Cabling required for each interface type

•Distance limitations for each signal type

•Additional interface equipment required

Connecting to the Console Port

The console port, labeled “Console”, is an RS-232 port with an RJ-45 interface

(see Figure 3-1 on page 3-3). The console port is an asynchronous (async) serial

port; any device connected to this port must be capable of asynchronous

transmission.

We recommend using this port to create a local management connection to set the

IP address and other initial configuration settings before connecting the switch to

the network for the first time.

Note Connecting the console port to a modem is supported for switches running Cisco

MDS SAN-OS Release 1.2(2a) or later.

Although the console port can be used to connect to a modem, the COM1 port is

recommended for this purpose.

Send documentation comments to [email protected].

3-3

Cisco MDS 9216 Switch Hardware Installation Guide

78-16165-01

Chapter 3 Connecting the Cisco MDS 9216 Switch Connecting to the Console Port

Caution If you do want to connect the console port to a modem, do not connect it while

the switch is booting; connect either before powering the switch on or after the

switch has completed the boot process.

You can use the console port to perform the following functions:

•Configure the Cisco MDS 9500 from the CLI

•Monitor network statistics and errors

•Configure SNMP agent parameters

•Download software updates

Note To connect the console port to a computer terminal, the computer must support

VT100 terminal emulation. The terminal emulation software—frequently an

application such as HyperTerminal or Procomm Plus—makes communication

between the Cisco MDS 9216 Switch and computer possible during setup and

configuration.

Figure 3-1 Connecting to the Console Port on the Cisco MDS 9216 Switch

FAN

STATUS

FAN-MOD-2

21 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16

STATUS

SYSTEM

RESET

CONSOLE MGMT 10/100

MDS 9216 COM1

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16

91679

Console

Send documentation comments to [email protected].

Chapter 3 Connecting the Cisco MDS 9216 Switch

Connecting to the COM1 Port

3-4

Cisco MDS 9216 Switch Hardware Installation Guide 78-16165-01

To connect the console port to a computer terminal, follow these steps:

Step 1 Configure the terminal emulator program to match the following default port

characteristics: 9600 baud, 8 data bits, 1 stop bit, no parity.

Step 2 Connect the supplied RJ-45 to DB-9 female adapter to the computer serial port.

We recommend using the adapter and cable provided with the switch.

Step 3 Connect the console cable (a rollover RJ-45 to RJ-45 cable) to the console port

(see Figure 3-1) and to the RJ-45 to DB-9 adapter at the computer serial port.

Note For configuration instructions, refer to the Cisco MDS 9000 Family Configuration

Guide.

Connecting to the COM1 Port

Note The COM1 port is not supported for connection to a console.

The COM1 port (labeled “COM1”) is an RS-232 port with a DB-9 interface. You

can use it to connect to an external serial communication device such as a modem.

For information about how to turn off hardware flow control, refer to the Cisco

MDS 9000 Family Configuration Guide.

Note Connecting the COM1 port to a modem is supported for switches running Cisco

MDS SAN-OS Release 1.2(1a) or later.

Send documentation comments to [email protected].

3-5

Cisco MDS 9216 Switch Hardware Installation Guide

78-16165-01

Chapter 3 Connecting the Cisco MDS 9216 Switch Connecting to the COM1 Port

Figure 3-2 Connecting to the COM1 Port on the Cisco MDS 9216 Switch

To connect the COM1 port to a modem, follow these steps:

Step 1 Connect the modem to the COM1 port using the adapters and cables provided

with the accessory kit, as follows: connect the DB-9 serial adapter labeled for use

with the Cisco MDS 9216 Switch to the COM1 port, connect the RJ-45 to DB-25

modem adapter to the modem, then connect the adapters using the RJ-45 to RJ-45

rollover cable (or equivalent crossover cable).

Note Use the green DB-9 adapter that is specifically labeled for use with the

Cisco MDS 9216 Switch. If this adapter is not included in the accessory

kit, you can request one from your customer service representative.

Step 2 If the default settings for the COM1 port have been modified, refer to the Cisco

MDS 9000 Family Configuration Guide for information regarding verifying and

resetting the default settings.

FAN

STATUS

FAN-MOD-2

21 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16

STATUS

SYSTEM

RESET

CONSOLE MGMT 10/100

MDS 9216 COM1

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16

99283

Send documentation comments to [email protected].

Chapter 3 Connecting the Cisco MDS 9216 Switch

Connecting to the MGMT 10/100 Ethernet Port

3-6

Cisco MDS 9216 Switch Hardware Installation Guide 78-16165-01

The default COM1 settings are as follows:

line Aux:

Speed: 9600 bauds

Databits: 8 bits per byte

Stopbits: 1 bit(s)

Parity: none

Modem In: Enable

Modem Init-String -

default : ATE0Q1&D2&C1S0=1\015

Statistics: tx:17 rx:0 Register Bits:RTS|DTR

Connecting to the MGMT 10/100 Ethernet Port

Caution To prevent an IP address conflict, do not connect the MGMT 10/100 Ethernet port

to the network until the initial configuration is complete. For configuration

instructions, refer to the Cisco MDS 9000 Family Configuration Guide.

The MGMT 10/100 Ethernet port (labeled MGMT 10/100) is autosensing and has

an RJ-45 interface (Figure 3-3 on page 3-7). You can use this port to access and

manage the switch by IP address, such as through Fabric Manager.

Send documentation comments to [email protected].

3-7

Cisco MDS 9216 Switch Hardware Installation Guide

78-16165-01

Chapter 3 Connecting the Cisco MDS 9216 Switch Connecting to a Fibre Channel Port

Figure 3-3 Connecting to the MGMT 10/100 Ethernet Port on the Cisco MDS

9216 Switch

To connect the MGMT 10/100 Ethernet port to an external hub, switch, or router,

follow these steps:

Step 1 Connect the appropriate modular cable to the MGMT 10/100 Ethernet port:

•Use modular, RJ-45, straight-through UTP cables to connect the 10/100

management port to an Ethernet switch port or hub.

•Use a cross-over cable to connect to a router interface.

Step 2 Connect the other end of the cable to the device.

Connecting to a Fibre Channel Port

The Fibre Channel ports on the switch modules are compatible with LC-type

fiber-optic SFP transceivers and cables (see Figure 3-4 on page 3-9). You can use

the Fibre Channel ports to connect to the SAN or for in-band management. For

information about configuring the switch for inband management, refer to the

Cisco MDS 9000 Family Configuration Guide.

FAN

STATUS

FAN-MOD-2

21 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16

STATUS

SYSTEM

RESET

CONSOLE MGMT 10/100

MDS 9216 COM1

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16

99329

MGMT 10/100

Send documentation comments to [email protected].

Chapter 3 Connecting the Cisco MDS 9216 Switch

Connecting to a Fibre Channel Port

3-8

Cisco MDS 9216 Switch Hardware Installation Guide 78-16165-01

The Cisco MDS 9000 Family supports both Fibre Channel and Gigabit Ethernet

protocol for SFP transceivers. Each transceiver must match the transceiver on the

other end of the cable, and the cable must not exceed the stipulated cable length

for reliable communications. Refer to the release notes for the list of specific

supported SFP transceivers. SFP transceivers can be ordered separately or with

the Cisco MDS 9216 Switch.

Warning

Invisible laser radiation may be emitted from disconnected fibers or

connectors. Do not stare into beams or view directly with optical instruments.

Statement 1051

Caution Wear an ESD-preventive wrist strap connected to the chassis when handling

transceivers. Keep optical connectors covered when not in use, and do not touch

connector ends. Avoid removing and inserting transceivers more often than

necessary.

Caution To prevent damage to the fiber optic cables, do not place more tension on them

than the rated limit and do not bend to a radius of less than 1 inch if there is no

tension in the cable, or 2 inches if there is tension in the cable.

Note Use only Cisco SFP transceivers on the Cisco MDS 9216 Switch. Each Cisco SFP

transceiver is encoded with model information that enables the switch to verify

that the SFP transceiver meets the requirements for the switch. For instructions

specific to the transceiver type, refer to the Installation Notes for the Cisco Small

Form-Factor Pluggable Modules provided with the transceiver.

Send documentation comments to [email protected].

3-9

Cisco MDS 9216 Switch Hardware Installation Guide

78-16165-01

Chapter 3 Connecting the Cisco MDS 9216 Switch Connecting to a Fibre Channel Port

Figure 3-4 Connecting an LC-Type Cable to an SFP Transceiver

Installing an SFP Transceiver and Fiber Optic Cable

To connect an SFP transceiver and fiber optic cable to a Fibre Channel port, follow

these steps:

Step 1 Verify that the transceiver and cable type both have LC-connectors and are the

required type for longwave or shortwave transmission and the required distances.

The transceiver label generally lists the model and wavelength.

Step 2 Remove the dust plug from the port end of the transceiver by pressing the trigger

on top of the plug to release the latch (clicks open) and pulling the plug out.

Step 3 Align and insert the transceiver into the port until the latch clicks. Transceivers

are keyed to prevent incorrect installation; if it does not slide in easily, verify it is

correctly oriented.

Step 4 Remove the dust plugs from the cable and the cable-end of the transceiver.

Step 5 Align and insert the cable end into the transceiver (see Figure 3-4) until the latch

clicks. Cables are keyed to prevent incorrect installation. If the cable does not

slide in easily, verify it is correctly oriented.

Step 6 Connect the other end of the cable to the external end system or switch.

For instructions on verifying connectivity on a module port, refer to the

Cisco MDS 9000 Family Configuration Guide.

1LC plug of fiber optic cable 2SFP transceiver

94986

Send documentation comments to [email protected].

Chapter 3 Connecting the Cisco MDS 9216 Switch

Connecting to a Fibre Channel Port

3-10

Cisco MDS 9216 Switch Hardware Installation Guide 78-16165-01

Removing an SFP Transceiver and Fiber Optic Cable

Caution When pulling a cable from a transceiver, grip the body of the connector. Do not

pull on the jacket sleeve, since this can compromise the fiber-optic termination in

the connector.

To remove an SFP transceiver and fiber optic cable from a Fibre Channel port,

follow these steps:

Step 1 Press the latch on top of the SFP to release the lock and gently pull the transceiver

from the port.

Step 2 If desired, remove the cable from the transceiver by pressing the latch on the cable

and pulling the cable from the transceiver.

Step 3 Cover the ends of the transceiver and the cable with the appropriate dust caps.

Maintaining SFP Transceivers and Fiber Optic Cables

SFP transceivers and fiber optic cables must be kept clean and dust-free to

maintain high signal accuracy and prevent damage to the connectors. Attenuation

(loss of light) is increased by contamination, and should be below 0.35 dB.

Maintenance guidelines:

•SFP transceivers are static sensitive. To prevent ESD damage, wear an

ESD-preventive wrist strap that is connected to the chassis.

•Do not remove and insert a transceiver more often than necessary. Repeated

removals and insertions can shorten its useful life.

•Keep all optical connections covered when not in use. If they become dusty,

clean before using to prevent dust from scratching the fiber optic cable ends.

•Do not touch ends of connectors to prevent fingerprints and other

contamination.

Autres manuels pour Cisco mds 9216 - fabric switch

Table des matières

Autres manuels Cisco Changer

Cisco

Cisco BPX-BXM-155-8DX Manuel de l'opérateur

Cisco

Cisco NM-16ESW-PWR= Manuel d'exploitation et d'entretien

Cisco

Cisco SFS 7012 InfiniBand Manuel d'installation

Cisco

Cisco UBR-MC20X20V Manuel

Cisco

Cisco IAD2423-16FXS-RF - IAD 2423 Router Guide de l'utilisateur

Cisco

Cisco OL-12518-01 Manuel

Cisco

Cisco Nexus 93240YC-FX2 Manuel

Cisco

Cisco Catalyst 2955 Series Manuel

Cisco

Cisco LightStream 1010 Manuel utilisateur

Cisco

Cisco Nexus 9504 Manuel

Cisco

Cisco Catalyst 4500 Series Manuel utilisateur

Cisco

Cisco 3560G-24PS - Catalyst Switch Dimensions

Cisco

Cisco Nexus 5000 NX-OS Manuel utilisateur

Cisco

Cisco Small Business 200 Series Mode d’emploi

Cisco

Cisco Catalyst Express 520 Manuel utilisateur

Cisco

Cisco TOPSPIN SFS 3012 Manuel utilisateur

Cisco

Cisco OL-4419-06 Manuel utilisateur

Cisco

Cisco Nexus 9364C Manuel

Cisco

Cisco 3550 48 - Catalyst SMI Switch Mode d’emploi

Cisco

Cisco Catalyst 2900 Series XL Guide d'installation

Cisco

Cisco Nexus 5000 Series Manuel utilisateur

Cisco

Cisco Nexus 9348D-GX2A Manuel

Cisco

Cisco SR2024 - Small Business Unmanaged Switch Manuel utilisateur

Cisco

Cisco Catalyst 3550 Manuel utilisateur

Manuels Changer populaires d'autres marques

URC

URC Total Control MFS-8 Manuel utilisateur

Azbil

Azbil HPQ-D11 Manuel utilisateur

Sony

Sony DFS-900M Manuel utilisateur

SICK

SICK i17S Manuel utilisateur

F&F

F&F SZR-277 Manuel utilisateur

Shure

Shure UAMS/BK Manuel utilisateur

Dräger

Dräger X-zone Switch Off Manuel utilisateur

Asco

Asco Joucomatic 349 Series Manuel utilisateur

BT Mini Hub Manuel utilisateur

D-Link

D-Link DES-1226G Manuel utilisateur

Johnson Controls

Johnson Controls FS80-C Manuel utilisateur

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manuel utilisateur

MicroNet

MicroNet SP1200A Manuel utilisateur

Ruijie

Ruijie RG-PF2920 Series Manuel d'installation et d'exploitation

Altinex

Altinex DA1914SX Manuel utilisateur

MiLAN

MiLAN MIL-SM2401M Manuel utilisateur

RJM

RJM MASTERMIND PBC/6X Manuel utilisateur

Atlas

Atlas MMK-KVM8 Manuel utilisateur