Cisco 6901 Standard Manuel utilisateur
Cisco Unified IP Phone Wall Mount
•Wall Mount Components for Cisco Unified IP Phone 6901, on page 1
•Wall Mount Components for Cisco Unified IP Phone 6911, on page 4
•Adjust Handset Rest, on page 9
Wall Mount Components for Cisco Unified IP Phone 6901
The following section describes how to install the Wall Mount plate for use with the Cisco Unified IP Phone
6901.
Cisco recommends that you use the Leviton Wall Mount plate (Leviton type number: 4108W-0SP) for mounting
the Cisco Unified IP Phone 6901. The wall mount plate must be ordered separately from the phone.
The following figure and table show a list of items required to mount the Cisco Unified IP Phone 6901 on the
wall using the Leviton Wall Mount plate.
Figure 1: Leviton Wall Mount plate
Leviton Wall Mount Plate2RJ45 Connector1
Cisco Unified IP Phone Wall Mount
1
Install Phone on Wall Mount Plate
To install the phone on the wall mount plate, perform these steps:
Procedure
Step 1 Plug the telephone line cord (RJ45 connector) into the phone jack at the base of the phone.
Figure 2: RJ45 Connector in the Phone Jack
Network Port on the Phone1
RJ45 Connector2
Step 2 Plug the RJ45 connector into the wall mount phone jack.
Figure 3: RJ45 Connector in the Wall Mount Jack
Cisco Unified IP Phone Wall Mount
2
Cisco Unified IP Phone Wall Mount
Install Phone on Wall Mount Plate
Wall Mount Plate3Network Port on the Phone1
Network Port on the Wall Mount Plate4RJ45 Connector2
Step 3 Slip the mounting holes on the base of the wall mount plate and over the wall mount pins.
Figure 4: Mounting Holes
Mounting Hole on the Phone1
Wall Mount Pin on the Wall Mount Plate2
Step 4 Firmly slide the IP Phone down into place.
Figure 5: Sliding the IP Phone
Cisco Unified IP Phone Wall Mount
3
Cisco Unified IP Phone Wall Mount
Cisco Unified IP Phone Wall Mount
Step 5 Change the handset as described in Adjust Handset Rest, on page 9.
Wall Mount Components for Cisco Unified IP Phone 6911
The following section describes how to install the wall mount for use with the Cisco Unified IP Phone 6911.
The following figure shows a list of items included in the Wall Mount Kit for the Cisco Unified IP Phone
6911.
Figure 6: Wall Mount Kit for Cisco Unified IP Phone 6911
The package includes the following items:
• One phone bracket
• One wall bracket
• Four #10-12x1-inch Phillips-head screws with 4 anchors
• Two #4-40x1/4-inch machine screws
• One 6-inch Ethernet cable
• One key if the bracket includes the optional lock
Before You Begin
You need these tools to install the bracket:
• #1 and #2 Phillips-head screwdrivers
• Level
You must also install an Ethernet jack for the telephone in the desired location if an Ethernet jack does not
currently exist. This jack must be wired appropriately for an Ethernet connection. You cannot use a regular
telephone jack. For more information on phone installation requirements and warnings, see Cisco Unified IP
Phone Installation.
Cisco Unified IP Phone Wall Mount
4
Cisco Unified IP Phone Wall Mount
Wall Mount Components for Cisco Unified IP Phone 6911
Install Bracket
To install the phone on the wall, perform these steps:
Procedure
Step 1 Mount the wall bracket in the desired location. You can install the wall bracket over an Ethernet jack, or you
can run the Ethernet network cable to a jack nearby.
a) Use the level to ensure the wall bracket is level, then use a pencil to mark the screw holes.
b) Using a #2 Phillips-head screwdriver, carefully center the anchor over the pencil mark and press the anchor
into the wall to make markings on the wall.
c) Screw the anchor clockwise into the wall until it is seated flush.
d) Use the included screws and a #2 Phillips-head screwdriver to attach the wall bracket to the wall.
Cisco Unified IP Phone Wall Mount
5
Cisco Unified IP Phone Wall Mount
Install Bracket
Figure 7: Mounting the Wall Bracket
Step 2 Attach the phone bracket to the IP Phone.
a) Detach the handset cord (and headset cord, if there is a headset), power cord, and any other attached cords
from the base of the phone.
b) Remove the label covers that are concealing the screw holes.
c) Attach the phone bracket by inserting the tabs into the mounting tabs on the phone. The phone ports should
be accessible through the holes in the bracket.
d) Secure the phone bracket to the IP Phone with the Phillips-head screws.
e) Thread the handset cord (and headset cord, if using one). Reattach the cords and seat them in the clips
incorporated into the phone body.
Cisco Unified IP Phone Wall Mount
6
Cisco Unified IP Phone Wall Mount
Cisco Unified IP Phone Wall Mount
Figure 8: Attaching the Phone Bracket
Step 3 Attach the Ethernet cable to the 10/100 SW network port and wall jack.
If you are connecting a network device (such as a computer) to the phone, attach the cable to the 10/100 PC
access port.
If you are using an external power supply, plug the power cord into the phone and dress the cord by clipping
it into the clips incorporated into the phone body next to the 10/100 PC port.
Cisco Unified IP Phone Wall Mount
7
Cisco Unified IP Phone Wall Mount
Cisco Unified IP Phone Wall Mount
Figure 9: Attaching the Cables
Step 4 Attach the phone to the wall bracket by inserting the tabs on the top of the phone bracket into the slots on the
wall bracket. Ensure that the power cord and any other cable that does not terminate in the wall behind the
bracket are positioned in one of the cable-access openings in the bottom of the bracket. The phone and wall
bracket openings together form circular openings with room for one cable per opening.
Step 5 Use the locking key to lock the phone to the wall bracket.
Cisco Unified IP Phone Wall Mount
8
Cisco Unified IP Phone Wall Mount
Cisco Unified IP Phone Wall Mount
Figure 10: Attaching the Phone to the Wall Bracket
Step 6 Change the handset as described in Adjust Handset Rest, on page 9.
Adjust Handset Rest
With a wall-mounted phone, you might need to adjust the handset rest to ensure that the receiver does not slip
out of the cradle. The hook should have a lip on which the handset catches when the phone is vertical. Follow
the diagram and steps below to change the hookswitch hook.
Cisco Unified IP Phone Wall Mount
9
Cisco Unified IP Phone Wall Mount
Adjust Handset Rest
Figure 11: Adjust the Handset Hook
Remove the handset from the cradle and pull the plastic tab from the handset rest.1
Rotate the tab 180 degrees.2
Hold the tab between two fingers, with the corner notches facing you.3
Line up the tab with the slot in the cradle, and press the tab evenly into the slot. An extension
protrudes from the top of the rotated tab. Return the handset to the handset rest.
4
Cisco Unified IP Phone Wall Mount
10
Cisco Unified IP Phone Wall Mount
Cisco Unified IP Phone Wall Mount
Autres manuels pour 6901 Standard
8
Ce manuel convient aux modèles suivants
1
Table des matières
Autres manuels Cisco Support et étagère
Cisco
Cisco NXK-ACC-KIT2-2RU Manuel utilisateur
Cisco
Cisco MERAKI MA-MNT-MR-H3 Manuel utilisateur
Cisco
Cisco UCS C890 M5 Manuel utilisateur
Cisco
Cisco Webex Board 70S Manuel utilisateur
Cisco
Cisco 3G-AE015-R Manuel utilisateur
Cisco
Cisco 3600 Series Guide de démarrage rapide
Cisco
Cisco Nexus 7000 Series Manuel utilisateur
Manuels Support et étagère populaires d'autres marques
Salamander
Salamander Acadia AC/W/L400/WH Manuel utilisateur
Fohhn
Fohhn VAT-09 Guide de l'utilisateur
ricoo
ricoo FS0522 Manuel utilisateur
AMSOIL
AMSOIL BMK-22 Guide rapide
Kargo Master
Kargo Master 48220 Manuel utilisateur
Milestone AV Technologies
Milestone AV Technologies SIMPLICITY SLF2 Manuel utilisateur
