Cisco Catalyst 2900 Series XL Manuel utilisateur

TAKE OUT WHAT YOU NEED

CABLE THE SWITCH

ASSIGN SWITCH INFORMATION

ACCESS THE SWITCH FROM YOUR BROWSER

Quick Start Guide

CATALYST 2900 SERIES XL SWITCHES

SERIES

1X 2X

SERIES

10BaseT/

100BaseT

hub

10BaseT/

100BaseT

switch

10BaseT/

100BaseTX

workstations

Web-based or

SNMP-based

management

station

Cisco IOS

command-line

interface

Serial cable

10BaseT/

100BaseT

router

Crossover

cabling

Straight-through

cabling

Take Out What You Need

Note: You need to supply a Category 5 straight-through or crossover cables to connect to

Ethernet devices.

Catalyst 2900 series XL Ethernet switch

Hardware installation guide and

release notes

RJ-45-to-RJ-45 rollover console cable

AC power cable

RJ-45-to-DB-9 serial connector

RJ-45-to-DB-9 terminal connector

Rack-mount kit

Rubber feet

MODE

3x 4x 5x 6x 7x 8x

1x 2x

9x 10x 11x 12x 13x 14x 15x 16x 17x 18x 19x 20x 21x 22x 23x 24x

10BaseT/100BaseTX

1x 2x 3x 4x

100BaseFX

WS-X2914-XL-V

Tighten

Screws

ToActivate

WS-X2922-XL-V

Tighten

Screws

ToActivate

Installation

Guide

Release

Notes

Cable the Switch

MODE

3x 4x 5x 6x 7x 8x

1x 2x

9x 10x 11x 12x 13x 14x 15x 16x 17x 18x 19x 20x 21x 22x 23x 24x

10BaseT/100BaseTX

1x 2x 3x 4x

100BaseFX

RJ-45-to-RJ-45

Cat 5 straight-

through cable

RJ-45

Ethernet port

RJ-45

10/100 port

WS-X2914-XL-V

Tighten

Screws

To Activate

WS-X2922-XL-V

Tighten

Screws

To Activate

Connect PCs, Workstations,

Servers, and Routers

1Connect a Category 5 straight-through

cable (not supplied) to a 10/100 port on

the front panel of the switch.

2Connect the other end of the cable to

the RJ-45 port of the PC, workstation,

server, or router.

Connect Switches and Hubs

1Connect a Category 5 crossover cable

(not supplied) to a 10/100 port on the

front panel of the switch.

2Connect the other end of the cable to an

RJ-45 port of the target switch or hub.

Note: Use a straight-through cable to

connect two ports when one of the ports is

designated with an X. Use a crossover cable

to connect two ports when both ports are

designated with an X.

RJ-45

console port

RJ-45-to-RJ-45

rollover cable

RJ-45-to-DB-9 adapter

(labeled TERMINAL)

DC INPUTS FOR REMOTE

POWER SUPPLY

SPECIFIED IN MANUAL.

+5V @24A, +12V @1.0A

DC INPUTS FOR REMOTE

POWER SUPPLY

SPECIFIED IN MANUAL.

+5V @24A, +12V @1.0A

CONSOLE

DC INPUT

RATING

100-120/200-240V

2.0A/1.0A 50-60HZ

CONSOLE

DC INPUT

RATING

100-120/200-240V

2.0A/1.0A 50-60HZ

Connect the AC Power Cord

1Connect one end of the supplied AC

power cable to the switch rear panel.

Note: If you are connecting to a Cisco

600W AC redundant power system (RPS),

refer to the Catalyst 2900 Series XL

Installation Guide and the Cisco Redundant

Power System Hardware Installation Guide

for more information.

2Connect the other end of the power

cable to a grounded AC outlet.

Connect to Your Console

1Connect the supplied ﬂat, blue, rollover

cable to the CONSOLE port on the

switch rear panel.

2Connect the other end of the cable to a

terminal or PC with terminal-emulation

software. Use one of the supplied

adapters if you need to.

The terminal or emulation software

must match the settings on the console

port. Check your terminal or emulation

software to be sure it matches the

settingslistedbelow,andreconﬁgureitif

it does not.

—9600 baud

—No parity

—8 data bits

—1 stop bit

Assign Switch Information

The ﬁrst time that you access the switch, it

runs a setup program that prompts you for

IP and other conﬁguration information

necessary for the switch to communicate

with local routers and the Internet. This

information is also required if you plan to

use the Cluster Management Suite to

conﬁgure and manage the switch.

Note: If the switch will be a cluster

member managed through the IP address of

the command switch, it is not necessary to

assign IP information or a password. If you

are conﬁguring the switch as a standalone

switch or as a command switch, you must

assign IP information. Refer to the Cisco

IOS Desktop Switching Software

Conﬁguration Guide for more information.

IP Information Requirements

You will need the following information

from your system administrator:

• Switch IP address

• Subnet mask (IP netmask)

• Default gateway (router)

• Enable secret password

First-Time Startup

Use this procedure to assign IP information:

1Enter Yat the ﬁrst prompt.

Continue with configuration dialog?

[yes/no]: y

2Enter the switch IP address, and press

Return:

Enter IP address:

ip_address

3Enter the subnet mask, and press

Return:

Enter IP netmask:

ip_netmask

4Enter Yat the next prompt to specify a

default gateway (router):

Would you like to enter a default

gateway address? [yes]: y

5Enter the IP address of the default

gateway, and press Return.

IP address of the default gateway:

ip_address

6Enter a host name for the switch, and

press Return.

Note: On a command switch, the host

name is limited to 28 characters; on a

member switch to 31 characters. Do not use

-n, where n is a number, as the last character

in a host name for any switch.

Enter a host name:

host_name

7Enter a secret password, and press

Return.

Note: The password can be from 1 to 25

alphanumeric characters, can start with a

number, is case-sensitive, and allows spaces

but ignores leading spaces.

Enter enable secret:

secret_password

8Enter Yto enter a Telnet password:

Would you like to configure a

Telnet password? [yes] y

Note: The password can be from 1 to 25

alphanumeric characters, is case-sensitive,

allows spaces, but ignores leading spaces.

9Enter the Telnet password, and press

Return:

Enter Telnet password:

telnet_password

10 Enter Yto conﬁgure the switch as the

cluster command switch. Enter Nto

conﬁgure it as a member switch or as a

standalone switch.

Note: If you enter N, the switch appears as

acandidateswitchinClusterBuilder.Inthis

case, the message in Step 11 is not displayed.

Would you like to enable as a

cluster command switch? y

11 Assign a name to the cluster, and press

Return.

Enter cluster name:

cls_name

Note: The cluster name can be 1 to 31

alphanumeric characters, dashes, or

underscores.

12 The initial conﬁguration is displayed:

The following configuration command

script was created:

ip subnet-zero

interface VLAN1

ip address

172.20.153.36 255.255.255.0

ip default-gateway

172.20.153.01

hostname

host_name

enable secret 5 $1$M3pS$cXtAlkyR3/6Cn8/

line vty 0 15

password

telnet_password

snmp community private rw

snmp community public ro

cluster enable

cls_name

end

13 Verify that the information is correct.

—Iftheinformationiscorrect, enterY

at the prompt, and press Return.

—If the information is not correct,

enter Nat the prompt, press

Return, and begin again at Step 1.

Use this configuration? [yes/no]:y

Where to Go Next

After you complete the setup program, the

switch can run the created default

conﬁguration. If you want to change this

conﬁguration or want to perform other

management tasks, use one of these tools:

• Command-line interface (CLI)

• Cluster Management Suite from your

browser

To use the CLI, enter commands at the

switch> prompt. Refer to the Cisco IOS

Desktop Switching Software Conﬁguration

Guide or the Cisco IOS Desktop Switching

Command Reference (online only) for

conﬁguration information.

To use the Cluster Management Suite, go to

Section 4, “Access the Switch from Your

Browser.”

AJava browserplug-in isrequiredtoaccessthe HTMLinterface. Youcan downloadtheplug-in

from Cisco Connection Online (CCO). If you have a SmartNet support contract, you can log

in to the following URL and download the plug-in:

• http://www.cisco.com/cgi-bin/tablebuild.pl/cat2900XL

If you do not have a SmartNet contract, you can download the plug-in from the following URL:

• http://www.cisco.com/pcgi-bin/tablebuild.pl/cat2900XL

Follow the instructions that accompany the plug-in to install it on your computer.

After you have assigned an IP address to the switch and installed the plug-in, you can access the

switch from your browser and use the Cluster Management Suite to view or change

conﬁguration settings. If this is a command switch, you can also use the Cluster Management

application to conﬁgure other switches. To use web-based tools, follow the procedure to set the

appropriate browser options.

The web-based tools support the following platforms and network browsers:

Note: Netscape Communicator version 4.6 is NOT supported.

The switch checks the browser version when starting a session to ensure that the browser is

supported. If the browser is not supported, the switch displays a warning message.

Note: Refer to the release notes for additional requirements for setting up your browser.

Access the Switch from Your Browser

Operating System Minimum Operating System

Requirements Netscape

Communicator Microsoft Internet

Explorer

Windows 95 Service Pack 1 4.61 or 4.7 4.01a or 5.0

Windows 98 Second Edition 4.61 or 4.7 4.01a or 5.0

Windows NT Service Pack 3 4.61 or 4.7 4.01a or 5.0

Solaris 2.5.1

or higher SUN-recommended patch

cluster for the OS and Motif

library patch 103461-24

4.61 or 4.7 Not supported

Conﬁguring Netscape

Communicator (All Versions)

1From the menu bar, select

Edit>Preferences.

2In the Preferences window, click

Advanced.

3Select the Enable Java,Enable JavaScript,

and Enable Style Sheets check boxes.

4From the Advanced drop-down list, select

Cache.

5Under Document in cache is compared to

document on network, select Every time.

6Click OK.

Conﬁguring Internet Explorer

(4.01a)

Note: For the procedure to conﬁgure

Internet Explorer 5.0, refer to the Cisco IOS

Desktop Switching Software Conﬁguration

Guide.

1From the menu bar, select View>Internet

Options.

2In the Internet Options window, click

Advanced.

3Scroll through the list of options to Java

VM, select the Java JIT compiler enabled

and Java logging enabled check boxes,

and click Apply.

4Click General. In the Temporary Internet

Files section, click Settings. The Settings

window opens.

5Select Every visit to the page, and click

OK.

6In the Internet Options window, click

Security.

7In the Zone drop-down list, select

Trusted Sites Zone, and click Custom.

8Click Settings.

9In the Java>Java permissions section,

select Custom. Click the Java Custom

Setting, which appears at the bottom of

the window.

10 In the Trusted Sites Zone window, click

Edit Permissions.

11 If the buttons under Run Unsigned

Content are not available, select either

Medium or Low security in the Reset

Java Permissions list box. Click Reset.

12 Under Run Unsigned Content, select

Enable, and click OK.

13 In the Security Settings window, click

OK.

14 In the Internet Options window, click

Security. Verify that the Zone

drop-down list is set to Trusted Sites

Zone.

15 In the Trusted Sites Zone section, click

Add Sites.

16 In the Trusted Sites Zone window,

deselect the Require server veriﬁcation

check box.

17 In the Add this Web site to the Zone ﬁeld,

enter the IP address of the switch.

Note: If the you plan to use Cluster

Management for switch conﬁguration, you

mustenterthe address of theclustercommand

switch. You can also enter the addresses of the

member switches, but they are not required. If

you plan to use Visual Switch Manager (VSM)

forswitchconﬁguration,youmustentertheIP

address of each switch that you want to

manage. You do not need to delete the address

from the Trusted Sites list if the switch later

becomes a cluster member. Refer to the Cisco

IOS Desktop Switching Software

Conﬁguration Guide for more information.

18 Click Add, and then click OK.

19 In the Internet Options window, click

Apply, and then click OK.

Displaying the Access Page

Once the browser is conﬁgured, display the

Cluster Management Suite access page:

1Enter the IP address of the switch in the

Location ﬁeld if you are using Netscape

(the Address ﬁeld if you are using Internet

Explorer).

Note: You can cut and paste the switch IP

address from the window that you used to

complete the setup program.

2Press Return. The universal access page

for your switch displays.

Note: You are prompted with a message if

your browser version is not supported.

3Click Cluster Management Suite or

Visual Switch Manager to display the

appropriate Cluster Management

application.

For More Information

See the Catalyst 2900 Series XL Installation

Guide for detailed instructions on installing

the Catalyst 2900 series XL switch. See the

Cisco IOS Desktop Switching Software

Conﬁguration Guide for detailed

instructions on using the Cluster

Management Suite and the CLI to conﬁgure

and manage switches. See the release notes

for recent information about the

Catalyst 2900 series XL switch.

Autres manuels pour Catalyst 2900 Series XL

Table des matières

Autres manuels Cisco Routeur réseau

Cisco

Cisco 2950 - Catalyst Switch Manuel utilisateur

Cisco

Cisco 6160 Manuel

Cisco

Cisco ASR-920-24SZ-IM Manuel utilisateur

Cisco

Cisco 828 Manuel utilisateur

Cisco

Cisco 7604 Manuel utilisateur

Cisco

Cisco NCS 4216 Manuel utilisateur

Cisco

Cisco Small Business RV315W Manuel utilisateur

Cisco

Cisco 7600 Series Manuel

Cisco

Cisco ASR 9000 Series Manuel utilisateur

Cisco

Cisco ASR 901S Series Feuille d'instructions

Cisco

Cisco ASR 1002-X Guide d'installation

Cisco

Cisco Linksys WET610N Manuel utilisateur

Cisco

Cisco 3600 Series Manuel utilisateur

Cisco

Cisco Linksys SFE2000 Mode d’emploi

Cisco

Cisco Linksys WRT54G3GV2-ST Manuel utilisateur

Cisco

Cisco 1811W - Integrated Services Router Wireless Manuel utilisateur

Cisco

Cisco 1100 Series Mode d’emploi

Cisco

Cisco Linksys SE2800 Manuel utilisateur

Cisco

Cisco ASR 9000 Series Manuel d'utilisation

Cisco

Cisco RV130 Manuel utilisateur

Cisco

Cisco RV042 - Small Business Dual WAN VPN Router Manuel utilisateur

Cisco

Cisco 1805 Manuel utilisateur

Cisco

Cisco 1401 - 1401 Router - EN Guide de démarrage rapide

Cisco

Cisco ASR1002 - ASR 1002 Router Manuel utilisateur

Manuels Routeur réseau populaires d'autres marques

Allnet

Allnet ALL0333AU Manuel utilisateur

HomeSeer

HomeSeer HT-SEL Manuel utilisateur

Sercomm

Sercomm Genesis OC3505D Manuel utilisateur

Billion

Billion BIPAC 5102 Series Manuel utilisateur

TP-Link

TP-Link TD-8817 Manuel utilisateur

Motorola

Motorola MR1900 Manuel utilisateur

Digi

Digi IX14 Manuel utilisateur

XAVi

XAVi X8821e Manuel utilisateur

BEC

BEC 6200WZL Manuel utilisateur

MikroTik

MikroTik hAP ac3 Series Manuel utilisateur

Korenix

Korenix JetNet 5428G Series Manuel utilisateur

NETGEAR

NETGEAR FS526T - Switch Manuel utilisateur

Korenix

Korenix JetNet 5710G Series Manuel utilisateur

Automated Logic

Automated Logic ZN551 Manuel du propriétaire

EnGenius

EnGenius ESR-9710 Manuel utilisateur

LevelOne

LevelOne FBR-1416 Manuel utilisateur

Dynacord

Dynacord Promatrix 6000 Manuel utilisateur

Lorex

Lorex F5D8230-4 Manuel utilisateur