Cisco 7507 Manuel utilisateur
INSTALL THE HARDWARE
CONNECT THE RSP
START AND CONFIGURE THE SYSTEM
INSTALL FIELD REPLACEABLE UNITS (FRUS)
1
2
3
4
5
Quick Start Guide
Is Cisco documentation helpful? Click here or go to http://www.cisco.com/warp/public/732/docsurvey/rtg/ to
give us your feedback. CISCO 7507 ROUTER
57105
UPPER
POWER
LOWER
POWER NORMAL
1
Install the Hardware
ENABLE
ENABLE
EJECT
SLOT 0
SLOT 1
NORMAL
CPU HALT
RESET
AUX.
CONSOLE
ROUTE SWITCH PROCESSOR 2
SLAVE
MASTER
SLAVE/MASTER
H3888
Slot 0 1234 5 6
Upper
power supply
Chassis
grounding
receptacles
Lower
power supply
I
O
DC FAIL
AC POWER
I
O
DC FAIL
AC POWER
RSP slots
Captive
installation screw
Captive
installation screw
The Cisco 7507 has seven slots: slots 2 and 3 for the
Route Switch Processors (RSPs), and slots 0, 1, 4, 5,
and 6 for the interface processors. There are bays for
up to two AC-input or DC-input power supplies.
Onepowersupplyisshippedasstandardequipment;
a second power supply is optional. A second
(optional) power supply allows load sharing and
increased system availability.
Packing List
• 1 Cisco 7507 router
• 1 Route Switch Processor (RSP)
• Y-Adapter cables, 1 auxiliary and 1 console
• 1 AC power supply
• 1 AC power supply cable
• 1 Power cord
• 1 Anti-static wrist strap and documentation
2
Prepare to Install the Router
Install the Hardware
Note For detailed hardware installation
instructions and safety guidelines, refer to the Cisco
7500 Series Router Installation and Configuration
Guide, Site Preparation and Safety Guide, and the
Cisco 7500 Regulatory Compliance and Safety
Guide.
Warning Only trained and qualified
personnel should install, replace, or service
this equipment.
Step 1 Lift the router safely out of the packing
container.
Step 2 Ensure the power service at the site is
suitable for the router you are installing.
Step 3 Check the packing slip to ensure that all
the proper components are present.
Step 4 Confirm that you have the required tools
and parts:
For rack-mounting (optional):
• Two mounting brackets (left and right are
identical), each with an attached spanner bar
• Two chassis ears (each holds two captive
grommets)
• Fasteners
• Ten 10-32 x 5/8-inch LG Phillips pan-head
screws with integral washers
• Four M4 x 10-mm LG Phillips, flat-head screws
• Number 2 Phillips screwdriver
• One 7/16-inch open-end (or adjustable) wrench
if you will remove the chassis feet
• Tape measure or level (both optional)
• Ohmmeter if your installation requires the
chassis be electrically isolated from the rack
• Number 2 Phillips or 1/4-inch flat-blade
screwdriver for the power supply (Due to
productimprovements,somepowersuppliesuse
slotted screws, and others use Phillips screws.)
• Cable ties may be needed to temporarily anchor
the cables when installing the power supplies.
For DC-Input Power Supply:
• Twin-lead, 10-AWG cable terminal block
connection
• Single 10-AWG wire for the ground connection
• Number 1 Phillips or 3/16-inch flat-blade
screwdriver
For interface modules (optional):
• Number 1 Phillips or 3/16-inch flat-blade
screwdriver
3
Install the Router
Install the Hardware
ENABLE
ENABLE
EJECT
SLOT 0
SLOT 1
NORMAL
CPU HALT
RESET
AUX.
CONSOLE
ROUTESWITCH PROCESSOR 2
SLAVE
MASTER
SLAVE/MASTER
I
O
DCFAIL
ACPOWER
I
O
DCFAIL
ACPOWER
53488
Note To rack-mount the router, refer to the
“Rack-Mount the Router (Optional)” section on
page 4.
Caution Two people are required to
perform this step. Avoid sudden twists or
moves to prevent injury.
Step 1 With a person positioned at either side of
the chassis, grasp the bottom edge of the
chassis with one hand near the front and
the other near the back. Slowly lift the
chassis in unison. Place the chassis on a
bench or tabletop where the air intake
vent on the front of the chassis is not
drawing in exhaust air from other
equipment.
Step 2 Ensure that you have at least 3 or 4 feet
(0.91 to 1.22 m) of clearance around the
rear of the chassis to install power
supplies and perform maintenance on the
chassis.
Step 3 Proceed to the “Install Interface
Processors, Fillers, VIPs, or RSPs” section
on page 10.
4
Rack-Mount the Router (Optional)
Install the Hardware
53423
M4 x 10-mm long Phillips
flat-head screws (to attach
ears to chassis)
10-32 x 5/8-inch long Phillips
pan-head screws with integral
square cone washers
(for mounting brackets and
chassis ears to rack posts)
Chassis ear with
captive sliding
grommets
Bracket
To rack-mount a Cisco 7507 router, perform the
following steps:
Step 1 Mount the brackets to the rack posts.
Step 2 Secure the spanner bars.
Step 3 Attach the chassis ears.
Step 4 Mount the chassis.
5
Mount Brackets to the Rack Posts
Install the Hardware
53382
Rack post
Flange
Shielded side
Note The distance between the inner edges of the
left and right rack-mounting posts must be at least
17.72 inches (45.088 cm), and the distance between
theholes in themounting posts must be 18.31 inches
(46.5 cm) (+ .063 inches or .16 cm).
Step 1 Place the bracket on the inner side of the
rack post, with the flanged front edge of
the bracket in front of the rack post.
Step 2 Align the mounting holes in the bracket
with those in the rack post.
Step 3 Support the bracket with one hand, and
use the other hand to insert a 10-32 x
5/8-inch LG Phillips pan-head screw
through the bottom mounting hole on the
front of the bracket and into the rack post.
Step 4 Secure the top of the bracket to the rack
with two pan-head screws. Finger-tighten
the screws.
Step 5 Push the brackets as far apart as possible
before using a Number 2 Phillips
screwdriver to tighten the screws.
Step 6 Adjust the brackets if the distance
between them is less than 17.5 inches
(45.45 cm).
Step 7 Repeat Step 3 through Step 6 for the
remaining bracket. Use a level or tape
measure to ensure that the two brackets
are level in the rack.
6
Secure the Spacers
Install the Hardware
53380
A
B
C
Step 1 Loosen the 10-32 x 5/8-inch LG Phillips
pan-head screw at the end of the ledge of
the right-side bracket. This screw is the
anchor for the spanner bar.
Step 2 Remove the tape that secures the spanner
bar on the left bracket, and swing the bar
down(seeA) over the anchorscrewonthe
opposite bracket.
Step 3 If the spanner bar does not reach the
opposite bracket, loosen the pan-head
screws to allow more play between the
brackets.
Step 4 RepeatStep 1 through Step 3 to fastenthe
remainingspannerbartoitsanchorscrew.
(See C.)
Step 5 Push the brackets as far apart as possible
before tightening the screws.
Step 6 Use a Number 2 Phillips screwdriver to
tighten the six pan-head screws that
secure the brackets to the rack-mounting
posts, and the two anchor screws that
secure the spanner bars. (See B.)
Step 7 Adjust the brackets if the distance
between them is less than 17.5 inches
(44.45 cm).
7
Attach the Chassis Ears
Install the Hardware
H2297
OR
Center-mount
position
Flush-mount
position
Step 1 Position the ears on the chassis as follows:
• To flush-mount the chassis, place each ear so
thatthemountingstripsareflush with the end of
the chassis, and align the mounting holes in the
ear with those in the chassis.
• To center-mount the chassis, place each ear with
the mounting strips away from the end of the
chassis, and align the mounting holes in the ear
with those in the chassis.
Step 2 Use two M4 x 10-mm LG Phillips
flat-head screws to secure each ear to the
chassis.
8
Mount the Chassis in the Rack
Install the Hardware
H2298
Warning Two people are required to
perform this step.
Step 1 Slowly lift the chassis in unison. Lower it
until it rests on the two ledges of the
brackets.
Step 2 Slide the chassis back into the rack along
the ledges.
Step 3 To remove a chassis foot, use a 1/4-inch
flat-blade screwdriver or insert a
7/16-inch open-end wrench between the
underside of the chassis and the foot.
Table des matières
Autres manuels Cisco Routeur réseau
Cisco
Cisco ASR 920 series Mode d’emploi
Cisco
Cisco RV016 - Small Business - 10/100 VPN Router Manuel utilisateur
Cisco
Cisco RV260P Manuel utilisateur
Cisco
Cisco 1417 Manuel utilisateur
Cisco
Cisco RV180 Manuel utilisateur
Cisco
Cisco 8600 Manuel
Cisco
Cisco ASR 9000 Series Feuille d'instructions
Cisco
Cisco Unified Communications Manager 8.5(1) Manuel utilisateur
Cisco
Cisco GRS Manuel utilisateur
Cisco
Cisco 1805 Manuel utilisateur
Cisco
Cisco WRT54G2 Linksys Manuel utilisateur
Cisco
Cisco Internet Router Cisco 12404 Manuel de l'opérateur
Cisco
Cisco CGR 1120 Manuel utilisateur
Cisco
Cisco WRT310N Manuel utilisateur
Cisco
Cisco OL-4387-02 Manuel utilisateur
Cisco
Cisco ASR 920 series Mode d’emploi
Cisco
Cisco RV340 Series Guide de démarrage rapide
Cisco
Cisco uBR900 Series Manuel utilisateur
Cisco
Cisco 3640 Series Manuel utilisateur
Cisco
Cisco 807 Manuel
