Cisco 12016 Manuel utilisateur

Corporate Headquarters:

Cisco Systems, Inc., 170 West Tasman Drive, San Jose, CA 95134-1706 USA

Cisco 12016, Cisco 12416, and Cisco

12816 Router Unpacking Instructions

This document contains important instructions for unpacking Cisco 12016,

Cisco 12416, and Cisco 12816 Routers. The unpacking instructions cover both the

original 12016 series routers and the newer 12016 enhanced series routers.

Review these instructions before you open the shipping container. After you

unpack the system, follow the instructions in the Cisco 12016, Cisco 12416, and

Cisco 12816 Router Installation and Configuration Guide to install the router.

Note Original models of the 12016 series routers ship with their front

covers packaged, but newer enhanced models ship with their front

doors already attached to the chassis. The illustrations in this guide

reflect the original series and do not show the front door in place.

References to the enhanced series front doors are noted where

appropriate.

Cisco 12016, Cisco 12416, and Cisco 12816 Router Unpacking Instructions 78-16081-02

This document includes the following topics:

•System Unpacking Overview, page 3

•Tools and Equipment, page 8

•Unpacking the Router, page 8

•Regulatory, Compliance, and Safety Information, page 21

•Obtaining Documentation, page 21

•Documentation Feedback, page 23

•Obtaining Technical Assistance, page 23

•Obtaining Additional Publications and Information, page 26

Cisco 12016, Cisco 12416, and Cisco 12816 Router Unpacking Instructions

78-16081-02

System Unpacking Overview

Figure 1 shows an exploded view of the shipping package for the router.

Figure 1 Router Shipping Package Components

29660

Top cap

U-shaped panel

Foam cap

PalletAccessories package

OPEN

System Unpacking Overview

Cisco 12016, Cisco 12416, and Cisco 12816 Router Unpacking Instructions 78-16081-02

When it is packaged for shipment, the router is equipped as ordered, with all

components installed. Because of the weight and height of the router, the router

shipping pallet incorporates a scissor-jack platform that enables a team of two

installers to remove a fully loaded router from the pallet and insert it into an

equipment rack, or extract a fully loaded router from a rack, without removing any

of the components from the chassis.

The router is bagged to protect it against dust and electrostatic discharge (ESD)

and secured to the scissor-jack platform by four anchor clips. The anchor clips are

inserted into slots along the bottom edges of the chassis side panels and secured

to the scissor-jack platform by four bolts. In turn, the scissor-jack platform is

secured to the shipping pallet by eight hold-down brackets that are bolted to the

top of the shipping pallet.

Note The scissor-jack platform remains attached to the router until the routeris inserted

into the equipment rack. After the router is inserted in the rack, the scissor-jack

platform should be reinstalled on the shipping pallet. The entire shipping

container should be reassembled and stored.

Cisco 12016, Cisco 12416, and Cisco 12816 Router Unpacking Instructions

78-16081-02

System Unpacking Overview

The shipping pallet consists of a U-shaped wood and foam pallet body and a wood

and foam pallet front bar (Figure 2). The pallet front bar fastens to the open end

of the pallet body to create the fourth bearing surface for the scissor-jack platform

and to complete the base needed to support the walls of the shipping container.

Figure 2 Router Shipping Pallet Assembly

When the router and scissor-jack platform are installed on the pallet, the router

and scissor-jack platform are suspended over the well formed by the pallet body

and pallet front bar. By removing the front hold-down brackets from the pallet and

scissor-jack platform, you can remove the pallet front bar and expand the

scissor-jack platform to lower the platform base so that it supports the weight of

the router. After the bolts in the remaining hold-down brackets are removed from

the pallet, the router and scissor-jack platform can be separated from the pallet by

pulling the pallet body away from the scissor-jack platform.

SLOT-0

SLOT-1

RESET

AUX

CONSOLE

EJECT

ACTIVE

CARRIER

RXCELL

ACTIVE

CARRIER

RXPKT

DOWN

LOOP RA LA

CDHNT CD

DOWN

LOOP RA LA

CDHNT CD

ACTIVE

CARRIER

RXPKT

ACTIVE

CARRIER

RXPKT

ACTIVE

CARRIER

ACO/LT

CRITICAL

MAJOR

MINOR

29186

Top view of pallet parts

Pallet body

Pallet front bar

System Unpacking Overview

Cisco 12016, Cisco 12416, and Cisco 12816 Router Unpacking Instructions 78-16081-02

The accessories for the router ship in five boxes that are assembled into an

accessory package (Figure 3).

Figure 3 Accessory Package—Exploded view

9661

Bottom cap

Top cap

Center-mount

ack-mounting

brackets

Rack-mountin

platform

Corrugated

spacer

Cable

trough Cable

trough

Accessory box

Foam

Cisco 12016, Cisco 12416, and Cisco 12816 Router Unpacking Instructions

78-16081-02

System Unpacking Overview

The five accessory boxes include:

•One box that contains the rack-mounting platform, which must be installed in

the equipment rack before inserting the router.

•One box that contains two optional center-mount rack-mounting brackets.

•Two boxes that contain the two vertical cable-management troughs, which are

installed on either side of the router after it has been installed in the

equipment rack.

•One box that contains the remaining small accessory items, including:

–

The plastic front cover for the power shelf and upper blower module

(removed and packaged separately to allow the two foam inserts to be

fitted around the top of the router).

Note Enhanced models of the 12016 series routers ship with their front

door in place.

–

Printed copies of the customer documents that ship with the router.

–

Miscellaneous small hardware needed to install the router.

The side walls ofthe shippingcontainer are formed by two U-shaped, interlocking

corrugated panels. The panels overlap to form the narrow ends of the container

and are locked together by 12 plastic locking clips inserted into holes in the

corrugated panels. Two foam inserts fit around the top of the router to act as a

protective cushion and add rigidity to the packaging scheme by serving as a fixed

buffer between the router, the corrugated side walls of the shipping container, and

the corrugated top cap that holds the side walls in place. With the corrugated top

cap installed, the entire shipping package is double-strapped end-to-end and

side-to-side to secure the shipping container and its contents to the pallet.

Note Do not destroy the components of the shipping package. After installing the

router, reassemble and store one complete router shipping package so that you can

remove the router from the equipment rack and repackage the router in the event

it must be shipped to another site or—if necessary—returned to the factory.

If you do not receive the items you ordered, contact a Cisco customer service

representative for assistance.

Tools and Equipment

Cisco 12016, Cisco 12416, and Cisco 12816 Router Unpacking Instructions 78-16081-02

Tools and Equipment

You need the following tools and equipment to unpack the router:

•A knife or scissors (to cut the packaging straps on the shipping container)

•9/16-inch (14-mm) wrench(for chassis hold-down bolts and pallet hold-down

bracket bolts)

•3/4-inch (19-mm) socket and ratchet wrench

•Wire cutters

•Safety hand truck with retractable safety leg wheels and security strap, such

as the Stevens Appliance Truck Company “Escort,” Model STEV SRT-M-66

(distributed by McMaster-Carr as Model 2654T6), or an equivalent safety

hand truck.

Unpacking the Router

Unpack the router in two phases:

•Open and disassemble the shipping package to expose the router on the

shipping pallet

•Remove the router and scissor-jack platform from the shipping pallet

These two procedures are described next.

Opening and Disassembling the Shipping Package

To expose the router on the shipping pallet, use Figure 1 on page 3 as a reference

and follow these steps:

Step 1 Use a pallet jack or forklift to place the shipping container as close to the

installation location as possible. The unpacking site should be a large, open space

with a level, solid floor. The work space must be large enough to allow easy access

to all four sides of the shipping container.

Cisco 12016, Cisco 12416, and Cisco 12816 Router Unpacking Instructions

78-16081-02

Unpacking the Router

Step 2 To remove the corrugated top cap from the shipping container, follow these steps:

a. Cut the four straps that wrap around the sides of the container from top to

bottom.

b. Separate the top cap from the side panels and liftoff the cap fromthe shipping

container.

c. Safely set aside the top cap.

Step 3 To remove the corrugated U-shaped side panels, follow these steps:

a. At one of the narrow side panels containing the six plastic locking clips, insert

a finger into the hole in one of the plastic locking clips and pull the wedge

block out of the clip to release the butterfly tabs on the sides of the clip (see

the exploded detail of the plastic locking clip shown in Figure 1.)

b. Grasp the clip and pull it out of the hole in the corrugated panel.

c. Repeat Step a. and Step b. for the other five clips on the narrow side panel.

d. Repeat Step a. through Step c. for the opposite narrow side panel.

e. Lift the U-shaped side panel, pull it off the pallet, fold it flat, and set it safely

aside.

f. Repeat Step e. for the other U-shaped side panel.

Step 4 Remove the two foam inserts from the top of the router.

Step 5 Remove the corrugated, folded spacer from the top of the accessory package.

Step 6 Remove the accessory package from the pallet and set it away from the pallet.

Step 7 Slide the top cap off the accessory package.

Step 8 Remove each of the five accessory boxes and set them safely aside.

Note Do not destroy the components of the shipping package. After installing the

router, reassemble and store one complete router shipping package so that you can

remove the router from the equipment rack and repackage the router in the event

it must be shipped to another site or—if necessary—returned to the factory.

Unpacking the Router

Cisco 12016, Cisco 12416, and Cisco 12816 Router Unpacking Instructions 78-16081-02

Removing the Router from the Shipping Pallet

This section describes how to remove the router from the shipping pallet. Refer to

Figure 4 and Figure 5 for the location of items referred to in the steps.

Figure 4 shows the router and scissor-jack platform mounted on the shipping

pallet.

Figure 4 Router and Scissor-Jack Platform Mounted on the Shipping Pallet

29185

SLOT-0

SLOT-1

RESET

AUX

CONSOLE

EJECT

ACTIVE

CARRIER

RXCELL

ACTIVE

CARRIER

RXPKT

DOWN

LOOP RA LA

CDHNT CD

DOWN

LOOP RA LA

CDHNT CD

ACTIVE

CARRIER

RXPKT

ACTIVE

CARRIER

RXPKT

ACTIVE

CARRIER

ACO/LT

CRITICAL

MAJOR

MINOR

Front of

chassis

Scissor-jack screw

Blocking plate

Hold-down bracket

(4 bolts)

Autres manuels pour 12016

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Cisco Routeur réseau

Cisco

Cisco XR 12000 Manuel utilisateur

Cisco

Cisco Small Business RV320 Manuel utilisateur

Cisco

Cisco Cisco 760 Series Manuel utilisateur

Cisco

Cisco ASR 9000 Serie Manuel utilisateur

Cisco

Cisco MWR 1941-DC - 1941 Mobile Wireless Router Manuel

Cisco

Cisco VS-C6509E-S720-10G Manuel utilisateur

Cisco

Cisco 7246 - uBR Router Manuel utilisateur

Cisco

Cisco 1710 Manuel utilisateur

Cisco

Cisco XR 12000 Manuel utilisateur

Cisco

Cisco WRT350N Manuel utilisateur

Cisco

Cisco Catalyst 3560-X Series Manuel utilisateur

Cisco

Cisco ASR1006 - ASR 1006 Modular Expansion Base Manuel

Cisco

Cisco ASA 5585-X Manuel utilisateur

Cisco

Cisco XR 1200 series Manuel d'installation

Cisco

Cisco 7301 Series Manuel de l'opérateur

Cisco

Cisco 7000 and 7507 Chassis CHAS-7507 Mode d’emploi

Cisco

Cisco WRVS4400N - Small Business Wireless-N Gigabit Security... Manuel utilisateur

Cisco

Cisco 2611XM Manuel utilisateur

Cisco

Cisco SOHO Series Instructions originales

Cisco

Cisco Card Cage and Backplane 7513-MX Manuel utilisateur

Cisco

Cisco IR809 Manuel utilisateur

Cisco

Cisco 7200 VXR Series Manuel utilisateur

Cisco

Cisco ASR 1013 Manuel utilisateur

Cisco

Cisco MWR 1941-DC - 1941 Mobile Wireless Router Manuel utilisateur

Manuels Routeur réseau populaires d'autres marques

Allnet

Allnet ALL0333AU Manuel utilisateur

HomeSeer

HomeSeer HT-SEL Manuel utilisateur

Sercomm

Sercomm Genesis OC3505D Manuel utilisateur

Billion

Billion BIPAC 5102 Series Manuel utilisateur

TP-Link

TP-Link TD-8817 Manuel utilisateur

Motorola

Motorola MR1900 Manuel utilisateur

Digi

Digi IX14 Manuel utilisateur

XAVi

XAVi X8821e Manuel utilisateur

BEC

BEC 6200WZL Manuel utilisateur

MikroTik

MikroTik hAP ac3 Series Manuel utilisateur

Korenix

Korenix JetNet 5428G Series Manuel utilisateur

NETGEAR

NETGEAR FS526T - Switch Manuel utilisateur

Korenix

Korenix JetNet 5710G Series Manuel utilisateur

Automated Logic

Automated Logic ZN551 Manuel du propriétaire

EnGenius

EnGenius ESR-9710 Manuel utilisateur

LevelOne

LevelOne FBR-1416 Manuel utilisateur

Dynacord

Dynacord Promatrix 6000 Manuel utilisateur

Lorex

Lorex F5D8230-4 Manuel utilisateur