Cisco CP-8851 Manuel utilisateur

CP-8851 / CP-8861

Do Not Ship Enclosure with Phone Installed

[PHONE MUST BE INSTALLED ON-SITE]

- Due to the size and mass of this product, it is

Take into consideration before you install:

important that the Backbox is safely installed

according to these installation instructions.

- Make sure that the type of wall is capable of supporting

the system and use screws that are suitable for that type of wall.

- The system must be installed by qualied personnel, in

accordance with state and local building regulations.

- See sheet ve and ten for Conduit and Wall Mounting instructions.

CP-8851 / 9961 Mounting the Enclosure

Accessory Kits

Torx Sec. Bit & Spare Screw Kit

#6-32x5/8"Flat Head

Pin Torx Machine Screw

(Spare - 2 Pieces)

#00 Screw Driver Kit

Jumper Shunt #8 Hex Nut

#6-32 x3/16”

Button Head Torx

Machine Screw

(Spare)

(GND Lug)

Keypad Cover Accessory Kit

Hex L-Key

Coverplate

Mounting

Screw

Phone Mounting Screw Kit

Drilled Spanner Dirver Bit

Smaller

for Acrylic Bezel

Replacement

T-15 Pin Torx

Security Driver Bit

Cisco CP-8851 /

Cisco CP-8861

Then Connect Power Plug (1) &

Network Cable (2), etc. before

Install Mounting Bracket

Mounting

Bracket

Mounting

Screw (2 Pieces)

(1)

(2)

Remove Both

USB & KEM

Remove Handset &

Disconnect Cord from Phone.

Covers

Remove Handset, USB & KEM Covers,

Install all Cables then the Mounting Bracket

Plug in the USB Cable

USB Port

Right Angle

USB-A Plug

USB-B Plug in to

USB to Analog Audio Module

(See Sheet 6 of 10)

AUX

Cable

AUX

Tools Required:

1) Electric Powered Hand Drill

2) Drill Bit (Use Correct Drill Bit for Wood / Concrete)

Mount the Backbox Assembly

to the Wall

A) Prepare Hole on Drywall (with Stud Behind) / Concrete

B) Insert Stud Anchors in to Holes

C) Align Backbox Assembly Mounting Holes to Studs

Step 3

Figure Shown Typical Installation:

3) Leveler

4) Torque Wrench, Wrench and Socket

D) Tighten Washers and Nuts that included with Stud Anchors

E) Torque to Stud Anchors Manufacturer's Recommended ft./lbs.

110

USB-B

Black Wire to Terminal 4

Green Wire to Terminal 3

Yellow Wire to Terminal 2

Red Wire to Termianl 1

Terminal

Audio Module

USB to Analog

Hookswitch Cradle

Use Provided #00 Screw Driver

to Install Wires to Terminal Block

Connect Before Closing the Faceplate

Block

Handset Lanyard

Armored Cord

Handset Retainer

Factory Disconnected,

to Terminal 5

Red Wire

Black Wire

to Terminal 9

Black Wire

Hookswitch Cradle to Handset Connections

Armored Cord

Install Shunt on JP2

to Enable Auto Answer Mode

JP2

Shunt

Phone with

Backbox

Phone Mount

Assembly

Intall Phone with Phone Mount

to Backbox

Use Provided Security Torx

Driver Bit to Fasten Screws

to Backbox

Tool Required:

Electric Hand Drill or

Powered Screwdriver

Backbox

Assembly

Faceplate

Torx Screw (11x)

Assembly

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Cisco Téléphone IP

Cisco

Cisco SPA-500 Series Manuel utilisateur

Cisco

Cisco 7970G - IP Phone VoIP Mode d’emploi

Cisco

Cisco 8941 Manuel utilisateur

Cisco

Cisco 7902G - Unified IP Phone VoIP Manuel utilisateur

Cisco

Cisco 7905 Manuel utilisateur

Cisco

Cisco Cisco 7960 Manuel d'instructions

Cisco

Cisco SPA504 Manuel utilisateur

Cisco

Cisco 7916 Manuel utilisateur

Cisco

Cisco SPA 501G Mode d’emploi

Cisco

Cisco WIP310 - iPhone Wireless VoIP Phone Mode d’emploi

Cisco

Cisco 8851 Manuel utilisateur

Cisco

Cisco Small Business SPA 301 Mode d’emploi

Cisco

Cisco 3905 Manuel utilisateur

Cisco

Cisco DATAVOX 7941 Manuel utilisateur

Cisco

Cisco SPA525G - Small Business Pro IP Phone VoIP Manuel utilisateur

Cisco

Cisco 7800 Series Manuel utilisateur

Cisco

Cisco 7942G - Unified IP Phone VoIP Manuel utilisateur

Cisco

Cisco 7811 Manuel utilisateur

Cisco

Cisco 8851 Mode d’emploi

Cisco

Cisco M5 Manuel d'utilisation et d'entretien

Cisco

Cisco 7921 Manuel utilisateur

Cisco

Cisco 79 SERIES Manuel utilisateur

Cisco

Cisco 8800 Series Manuel utilisateur

Cisco

Cisco 7985G - IP Phone NTSC Video Mode d’emploi

Manuels Téléphone IP populaires d'autres marques

Alcatel

Alcatel 4028 Manuel utilisateur

Polycom

Polycom Polycom VVX 600 Manuel utilisateur

Polycom

Polycom SoundPoint IP 450 Manuel utilisateur

Polycom

Polycom SoundPoint IP 650 Manuel utilisateur

Proximus

Proximus Maestro 3016 IP Manuel utilisateur

Fanvil

Fanvil X4 Manuel utilisateur

Snom

Snom 320 Manuel utilisateur

Yealink

Yealink Yealink SIP-T46G Manuel utilisateur

Avaya

Avaya 4625SW Manuel utilisateur

Yealink

Yealink SIP-T52S Manuel utilisateur

Nortel

Nortel 1140E Manuel utilisateur

Nexotek

Nexotek NT-P500 Manuel utilisateur

Avaya

Avaya Integral 5 R3.0 Manuel utilisateur

GE 28320EE2 - Dect 6.0 InfoLink 2 Manuel utilisateur

Avaya

Avaya 4600 Series Manuel de service

Mitel

Mitel MIVOICE OFFICE 400 6940 SIP Manuel utilisateur

Nortel

Nortel i2050 Manuel utilisateur

Fiberme

Fiberme FAP260 Series Manuel utilisateur