Cisco CIAG-GW-IP10 Manuel utilisateur
CHAPTER
4-1
Cisco Physical Access Gateway User Guide
OL-20932-01
4
Connecting a Cisco Input Module
Overview
The optional Cisco Input Module (Figure 4-1) is attached to a Cisco Physical Access Gateway or Cisco
Reader Module to provide additional connections for up to ten input devices. Each connection can be
configured as supervised or unsupervised. A supervised connection is a four- state connection to
determine if the connection is (1) short (2) is open (3)normal state or (4) alarm state. An unsupervised
input indicates only normal or alarm.
Figure 4-1 Cisco Input Module
4-2
Cisco Physical Access Gateway User Guide
OL-20932-01
Chapter 4 Connecting a Cisco Input Module
Package Contents
The optional Cisco Input Module is connected to a Cisco Physical Access Gateway or Cisco Reader
Module using a CAN connection to provide connections for additional input devices, as, as shown in
Figure 4-2.
Figure 4-2 Cisco Reader Module connected to the Cisco Physical Access Gateway
Package Contents
Each Cisco Input Module includes the following:
•20 resistors (1K) for input supervision
•2 mounting brackets, with 4 screws for each bracket
•Regulatory compliance and safety information
•Quick start guide
271597
Cisco
IP Network
Additional
Input/Output devices
Additional
Input/Output devices
Door Readers
and Input/Output
devices
Door Readers
and Input/Output
devices
Cisco Input or Output
Module (Optional)
Cisco Input or Output
Module (Optional)
Cisco Reader
Module (Optional)
Cisco
Access Gateway
Cisco Access
Control Manager
CAN connection
CAN connection
CAN connection
Ethernet
Access Layer
switch
4-3
Cisco Physical Access Gateway User Guide
OL-20932-01
Chapter 4 Connecting a Cisco Input Module
Physical Overview and Port Description
•Connector plugs:
Physical Overview and Port Description
Each Cisco Input Module includes 10 ports for connecting additional input devices. as shown in
Figure 4-3.
Figure 4-3 Cisco Input Module Ports and Connectors
Type Quantity
3 Pin 1
2 Pin 13
1
2
5
6
4
3
187043
4-4
Cisco Physical Access Gateway User Guide
OL-20932-01
Chapter 4 Connecting a Cisco Input Module
Physical Overview and Port Description
Figure 4-4 Cisco Input Module Ports and Connectors: Top View
The following items are shown in Figure 4-3 and Figure 4-4:
45 6
1
2
3
187039
Type Description
1Power Two-pin connector for Voltage In (VIN) and Ground (GND) to
connect a 12 to 24 VDC external power source.
2CAN interface A 3-wire CAN bus is used to connect additional modules.
Note Modules are connected using the CAN1 interface. The
CAN2 interface is not supported in this release.
3CAN Terminator The CAN terminator switch is set to ON for the last device in a CAN
wiring bus. This switch is set to set to OFF for all other devices in
the CAN bus.
4Input connections Ten input interfaces used to sense the contact closure. Each input
can be configured as supervised or unsupervised and can be
configured to sense a Normally Open (NO) or Normally Closed
(NC) contact.
•An unsupervised input senses a simple contact closure state,
including Normal or Alarm. When connected to open contacts,
the terminal voltage range is 4V to 5V. For closed contacts, the
voltage range is 0V to 0.7V.
•A supervised input senses four contact states, including
Normal, Alarm, Open and Short. These inputs require 1K
End-Of-Line (EOL) termination resistors installed at the
contacts (two resistors are included in the accessory kits for
each Input port).
4-5
Cisco Physical Access Gateway User Guide
OL-20932-01
Chapter 4 Connecting a Cisco Input Module
Installing the Cisco Input Module
Status LEDs
Each input port includes a status LED that indicates the following information:
Installing the Cisco Input Module
Install a Cisco Input Module is provide additional input connections for a Cisco Reader Module or
Gateway
Before You Begin
Verify the following:
•Verify that the module has access to a power source. See Power Options and Requirements,
page 1-10 for more information.
•Verify that you have the necessary mounting brackets or other hardware. See Mounting a Gateway
or Optional Module, page 1-12.
Installation Procedure
To install the module, perform the following procedure:
Step 1 Mount the module to a wall. See Mounting a Gateway or Optional Module, page 1-12 for more
information.
8PF Power fail input: an unsupervised input that raises a “power fail”
alarm when the circuit is open. Can be configured as an additional
unsupervised port. The corresponding LED is red when circuit is
open (when no input is connected).
9TM Tamper input: an unsupervised input that raises a “tamper” alarm
when the circuit is open. Can be configured as an additional
unsupervised port. The corresponding LED is red when circuit is
open (when no input is connected).
Type Description
Table 4-1 Input Module LEDs
Status Description
OFF Input is not configured
GREEN Input is configured and in normal state
BLINKING GREEN Input is configured, and is receiving and alarm or other data.
BLINKING RED Input is configured, short
RED Input is configured, open
4-6
Cisco Physical Access Gateway User Guide
OL-20932-01
Chapter 4 Connecting a Cisco Input Module
Installing the Cisco Input Module
Step 2 Connect the module to the DC power source:
a. Insert a two-pin connector plug into the DC power port (Figure 4-5)
b. Connect the Voltage In (VIN) and ground (GND) wires.
See Power Options and Requirements, page 1-10 for more information.
Figure 4-5 Power Connections for the Input and Output Modules
The following items are shown in Figure 4-5:
Step 3 Connect the module to the CAN bus:
a. Insert a three-pin connector plug into the CAN1 port, as shown in Figure 4-6.
b. Connect the CAN wires to the CAN bus, as shown in Figure 4-7
c. Turn the CAN terminator ON if the device is the last device in a CAN wiring bus.
Note The CAN terminator switch in included on the Reader, Input and Output modules only (the Gateway is
always the first device in the CAN bus). Set the terminator switch to OFF for all other modules in the
CAN bus.
Note The CAN2 interface is not supported in this release.
See Optional Expansion Modules, page 1-6 for more information.
271599
1
2
Configuration Description
1DC power
GND (ground)
Connects the DC ground wire to the module.
2DC power
Voltage In (VIN)
Connects the DC Voltage In (VIN) wire to the module.
4-7
Cisco Physical Access Gateway User Guide
OL-20932-01
Chapter 4 Connecting a Cisco Input Module
Installing the Cisco Input Module
Figure 4-6 CAN Connections: Input and Output Modules
The following items are shown in Figure 4-6:
Figure 4-7 CAN Bus Wiring
Step 4 Connect input devices to the module:
a. Insert two-pin connector plugs into the input ports.
b. (Optional, for supervised input connections only). Install two End-Of-Line (EOL) 1K termination
resistors in each supervised input interface (one terminator in each connector). Figure 4-8 shows the
terminator installation for a Normally Closed (NC) and Normally Open (NO) input connection.
271598
23
1
4
Configuration Description
1CAN+ Connects to the positive terminal of the CAN bus.
2CAN- Connects to the negative terminal of the CAN bus.
3Shield Connects to GND and/or Shield.
3CAN Terminator Turn the terminator ON if the device is the last device in a CAN wiring
bus.
271589
Gateway Module Reader Module Input Module Output Module
CAN+
CAN-
Sheild
4-8
Cisco Physical Access Gateway User Guide
OL-20932-01
Chapter 4 Connecting a Cisco Input Module
Installing the Cisco Input Module
Figure 4-8 Input Connections: Cisco Physical Access Gateway and Reader Module
c. Connect the wires from the input devices.
Note Each of the input connections can be configured as supervised or unsupervised. The tamper
(TM) and power fail (PF) inputs can be configured as additional unsupervised ports. A
supervised input supports four states: normal, alarm, open and short. An unsupervised input
indicates only normal or alarm.
Step 5 See the Cisco Physical Access Manager User Guide for information to configure the module ports.
NC
NO
1K,, 1%
1K,, 1%
1K,, 1%
1K,, 1%
187838
Table des matières
Autres manuels Cisco Système d'E/S
