Cisco MX400 Manuel utilisateur

MX400 Installation Guide

This document describes how to install and set up the MX400 security appliance. Additional reference documents are

available online at: www.meraki.com/library/products.

MX400 Overview

The Meraki MX400 is an enterprise security appliance designed for for

distributed networks that require remote administration. It is ideal for

network administrators who demand both ease of deployment and a

state-of-the-art feature set. The MX400 appliance provides the following

new features:

• Four bypass (fail-to-wire) ports

• USB port, to support approved 3G/4G cards for failover to cellular

networks.

• Support for two interface modules. Each module can have either

eight 1Gbit

• RJ45 or SFP ports or two 10Gbit SFP+ ports.

• Dedicated management port.

• Rail-kit for rack mounting

Package contents

In addition to the MX400, the following are provided.

The MX400 front panel

Ports and Status Indicators

The MX400 uses LEDs to inform the user of the device's status. When the device powers on, all the Internet LEDs flash

twice. Additional functions are described below, from left to right.

Item Function LED Status Meaning

1 Power Solid orange Power is applied

Flashing green Operation in progress

Solid green Fully operational

2 Warning Off During boot or no USB

link

Orange

Device requires attention.

Dashboard will contain

additional information

3 Disk status Off No disk activity

Orange Requires attention

Green Disk activity

4 Bypass status Off WAN and LAN ports are

separated

Green

WAN and LAN ports are

connected through virtual

wire

Additional functions on the front panel are described below, from left to right.

Reset button

Insert a paper clip if a reset is required.

• A brief, momentary press: To delete a downloaded

configuration and reboot.

• Press and hold for more than 10 sec: To force the

unit into a full factory reset.

USB port USB 2.0 for 3G/4G wireless cards. Traffic status is

indicated by the USB LED.

Interface modules 1 - 2 Interface modules for extended connectivity.

SFP Combo ports

For optional SFP-SX (fiber) or SFP-TX (RJ45 copper)

GbE connectivity. The functionality of ports 8 and 8F,

and ports 9 and 9F, is mutually exclusive. Only one port

of a pair is supported at a time.

Using MX Expansion Slots and Modules

The MX400 has 2 expansion slots which can accept the following Meraki Interface Modules:

•IM-8-CU-1GB: Meraki 8 x 1 GbE Copper Interface Module for MX400 and MX600.

•IM-8-SFP-1GB: Meraki 8 x 1 GbE SFP Interface Module for MX400 and MX600.

•IM-2-SFP-10GB: Meraki 2 x 10 GbE SFP+ Interface Module for MX400 and MX600.

When replacing an interface module, follow the steps below:

1. Power down the MX400. Interface Modules are not hot-swappable.

2. Insert the new interface module or modules.

3. Power up the MX400.

4. Dashboard will automatically recognize the new module or modules.

Please take caution when working with Interface Modules. Failure to follow the process above can corrupt the unit and

void warranty.

The MX400 back panel

Please note that the serial number is located on the product label at the back panel of MX400.

Mounting hardware

The mounting hardware includes a rack mount rail kit. When installing the device, make sure that there is sufficient

space between the rear of the rack and other obstacles to ensure adequate airflow.

Safety guidelines

Regardless if you are using a wall power outlet (MAINS) or any other type of power connection (e.g., a UPC device),

always ensure that the power cord can be readily disconnected from the hardware unit.

Connecting to WAN

All Meraki MX devices must have an IP address. This section describes how to configure your local area network before

you deploy it. A local management web service, running on the appliance, is accessed through a browser running on a

client PC. This web service is used for configuring and monitoring basic ISP/WAN connectivity.

Setting up a static IP address

To ensure that the client PC is redirected to the local web service in the following step, you must disable all other

network services (ex: wi-fi) on your client machine.

Do the following to configure basic connectivity and other networking parameters:

1. UUsing a client machine such as a laptop, connect to the management port of the MX.

2. Using a browser on the client machine, access the appliance's built-in web service by browsing to

http://setup.meraki.com. (You do not have to be connected to the Internet to reach this address)

3. Click Uplink configuration under the Local status tab. The default credentials use the device serial number as

the username, with a blank password field.

4. Choose Static for the IP Assignment option.

5. Enter the IP address, subnet mask, default gateway IP and DNS server information.

Setting up a DHCP IP address

By default all MX devices are configured to DHCP from upstream WAN / ISP servers. Simply plug the MX's WAN /

Internet port to your upstream circuit and wait a few minutes for the unit to negotiate a DHCP address.

When the WAN connection is fully enabled, Internet LED will turn green.

Additional settings

Please note that all these settings below are accessible only via the local management console.

Setting VLANs

If your WAN uplink is on a trunk port, choose VLAN tagging > Use VLAN tagging and enter the appropriate value for

VLAN ID for your network.

Setting PPPoE

PPPoE authentication may be required if you are connecting MX device to a DSL circuit. You need to know your

authentication option and credentials (supplied by your ISP) in order to complete these steps.

• Choose Connection Type > PPPoE.

• Select your Authentication option.

• If you select Use authentication, enter appropriate values for Username and Password.

Web proxy settings

These settings take effect if the MX device has to fall back to using HTTP to contact the Cloud Controller. By default,

web proxy is disabled. To enable web proxy, do the following:

• Choose Web proxy > Yes.

• Enter values as appropriate for Hostname or IP and Port.

• If you require authentication, choose Authentication > Use authentication, and enter appropriate values for

Username and Password.

To apply all configuration settings to the appliance, be sure to click Save Settings at the bottom of the page.

Configuring physical link settings

To configure physical link settings on the Ethernet ports, click Local status > Ethernet configuration. You can enable

half duplex, full duplex, and autonegotiation, as well as set 10- or 100-Mbps data rates.

Table des matières

Autres manuels Cisco Pare-feu

Cisco

Cisco Firepower 1600 Manuel

Cisco

Cisco 881W - Integrated Services Router Wireless Mode d’emploi

Cisco

Cisco CSA 90 Series Manuel du produit

Cisco

Cisco RV110W Mode d’emploi

Cisco

Cisco LightStream 1010 Manuel utilisateur

Cisco

Cisco ASA 5506-X Manuel utilisateur

Cisco

Cisco Small Business Pro SA 520W Mode d’emploi

Cisco

Cisco 5510 - ASA SSL / IPsec VPN Edition Manuel utilisateur

Cisco

Cisco RV110W Manuel utilisateur

Cisco

Cisco Meraki MX64W Manuel utilisateur

Cisco

Cisco 5505 - ASA Firewall Edition Bundle Manuel utilisateur

Cisco

Cisco Firepower 4100 Series Manuel utilisateur

Cisco

Cisco M690 Manuel utilisateur

Cisco

Cisco TelePresence Server 7010 Manuel utilisateur

Cisco

Cisco C170 Manuel utilisateur

Cisco

Cisco 3110 Manuel

Cisco

Cisco Firepower 4100 Series Manuel utilisateur

Cisco

Cisco Small Business RV215W Manuel utilisateur

Cisco

Cisco ASA 5506-X Instructions d'installation

Cisco

Cisco Firepower 9300 Manuel

Cisco

Cisco Firepower 4100 Series Manuel d'installation

Cisco

Cisco ASA 5550 Series Manuel utilisateur

Cisco

Cisco PIX 501 Manuel utilisateur

Cisco

Cisco 5510 - ASA SSL / IPsec VPN Edition Manuel utilisateur

Manuels Pare-feu populaires d'autres marques

Fortinet

Fortinet FortiGate Voice Series Manuel utilisateur

ADTRAN

ADTRAN NetVanta 2300 Manuel utilisateur

SecureLogix

SecureLogix ETM System Manuel utilisateur

NETGEAR

NETGEAR ProSafe FVX538 Manuel utilisateur

Lanner

Lanner FW-8877 Manuel utilisateur

Huawei

Huawei USG6000 Series Manuel d'installation et d'exploitation

H3C

H3C SecPath F5000-AI-15 Manuel utilisateur

Nexcom

Nexcom DNA 1150 Manuel utilisateur

Fortinet

Fortinet FortiGate-60 series Manuel utilisateur

Draytek

Draytek Vigor2860 Series Manuel utilisateur

Lanner electronics

Lanner electronics FW-7650 Series Manuel utilisateur

Swisscom

Swisscom Internet Backup Manuel utilisateur

SonicWALL

SonicWALL NSa 5700 Manuel utilisateur

DPtech

DPtech FW1000 SERIES Manuel utilisateur

FEITIAN

FEITIAN MultiPass FIDO Manuel utilisateur

EBLOCKER

EBLOCKER PRO Manuel utilisateur

GTA

GTA GB-200 Manuel utilisateur

Trend Micro

Trend Micro Deep Edge Manuel utilisateur