CIS CIS-CRS354-48P Manuel utilisateur
CIS-CRS354-48P MANAGED L3 NETWORK SWITCH
PRODUCT MANUAL
CIS-CRS354-48P MANAGED L3 NETWORK SWITCH
PRODUCT MANUAL
Table of Contents
1. Welcome to Custom Integration Solutions™4
2. Package Contents 4
3. Overview 4
• Power 4
• PoE Output 4
• Ports 5
• LED Indicators 5
• Buttons 5
• Input Power Requirements 5
4. Rackmount Instructions 6
5. Accessing the Web Interface 7
• The Status Page 7
• Set the System Identity 8
• The Undo and Redo Buttons 8
• Show / Hide Passwords 8
• Changing the Default Password 9
• Rebooting the Device 9
• Setting the Clock 9
6. IP Addressing 10
• The DHCP Client Tab 10
• Renewing the DHCP lease 10
• Setting a Static IP Address 11
CIS-CRS354-48P MANAGED L3 NETWORK SWITCH
PRODUCT MANUAL
Table of Contents (continued)
7. View and Set Interfaces 12
• Power Cycling an Interface 12
• Loop Protect 13
8. VLANs 14
• Purchase VLAN Conguration 14
• VLAN Conguration 14
• Adding Ports to the VLAN(s) 15
9. PoE Information and Settings 16
• PoE-Out Modes 16
• PoE-Out Limitations 16
• Enable/Disable PoE on a Specic Port 16
10. Tools and Other Protocols 17
• SNMP 17
• UPnP 17
• The IP Scan Tool 18
• The Ping Tool 18
11. Warranty Information 19
CIS-CRS354-48P MANAGED L3 NETWORK SWITCH
PRODUCT MANUAL
1. Welcome to Custom Integration Solutions™
Thank you for purchasing CIS devices. Our solutions make it easy for integrators to deploy networks in home and business
settings with minimal conguration. Our support team can provide assistance in setting up the equipment and answering your
questions.
3. Overview
The CIS-CRS354-48P is a high performance managed switch that provides PoE on each of its 48 Gigabit Ethernet ports.
In addition to the PoE Ethernet ports, there are 4 SFP+ ports (up to 10 Gbps), and 2 QSFP+ ports (up to 40 Gbps).
The device is pre-congured with all ports switched together. We recommend you to set up a password to secure your device.
This unit is compatible with 1.25G SFP and 10G SFP+ modules. The device is capable of powering other devices through PoE.
Power
The unit is equipped with one IEC type AC power input, which accepts 100-240 V power (~ 50/60 Hz).
The power consumption of this device under maximum load is 800 W with attachments, 85 W without attachments.
PoE output
This device can supply PoE to external devices. The output voltage will be selected automatically, depending on the voltage
the connected device requires. The device can power both 802.3af/at devices and devices that accept passive PoE power. If
necessary, the output voltage can be switched manually.
By default the PoE mode is set to auto. It will not damage non-PoE devices and will auto-detect devices with PoE support and
their required voltage. Once a PoE device is detected, it will be powered and the PoE LEDs will turn on.
The switch can output a total of 1000 mA per port at <30 V, and 570 mA at >30 V. The total current output at 26 V is 27A, and
13.2 A at 53V.
The max wattage per port is 26 W at 26 V, and 30 W at 53 V.
2. Package Contents
Switch (1) Rack Ears (2)
Rack hooks (2)
Rear supports (2)
IEC Power
Cord (1) Rack
Screws Cable Management
Brackets (2)
CIS-CRS354-48P MANAGED L3 NETWORK SWITCH
PRODUCT MANUAL
Buttons
Reset button: Hold this button during while the device is powered off, then apply power. Keep holding until the USR LED light
starts ashing, (5 seconds) then release the button to reset to the default CIS conguration. You can use this procedure if you
have forgotten the password to access the device, or simply wish to return the unit to its default conguration state.
LED indicators
• Power LED - lit when the switch is powered on.
• Fault LED - indicates a fault has occurred. Contact CIS if this light is lit.
The top row LEDs indicate PoE out status. A green LED indicates that the respective port uses low voltage, a red LED indicates
high voltage. The direction of the arrow indicates which port it is referring to.
• A ashing green LED - indicates a problem with a low voltage device.
• A ashing red LED - indicates a problem with a high voltage device.
• The bottom row LEDs indicate ethernet and SFP port activity.
Ports
• 48 Gigabit Ethernet ports (With Auto MDI/X — You can use straight-through or cross-over cables for connecting devices
to the switch).
• 4 SFP+ cages,
• 2 QSFP+ cages
• RJ45 “Console” serial port—disabled by default.
Input Power Requirements
Supported input voltage-100V AC-240V AC
CIS-CRS354-48P MANAGED L3 NETWORK SWITCH
PRODUCT MANUAL
4. Rackmount Instructions
3. Attach the rear support ears to the rack with two screws on each side.
4. Move the switch into place using the rear supports to hold it. Attach the switch to the front of the rack with rack screws.
5. Attach the cable management brackets to the rack (optional).
1. Attach the rack ears to the front sides of the switch with four screws on each side.
2. Attach the rear support hook to the rear sides of the switch with two screws on each side.
CIS-CRS354-48P MANAGED L3 NETWORK SWITCH
PRODUCT MANUAL
5. Accessing the Web Interface
1. Connect your laptop to any remaining port on the front of the CIS Switch. Ensure your computer is set to DHCP mode.
2. Obtain the IP address of the CIS switch in the DHCP leases of your CIS router. Open a web browser and enter the IP address
in the address bar.
3. To login, enter the username cis and password integration.
4. Integrators may use the Get TeamViewer link if remote assistance is required.
cis
integration
The Status Page
The status page provides basic diagnostic information. There is a CIS Support Address should you require assistance. The
switch’s Identity will show you which switch you are accessing on your network. You can view uptime, memory usage and load
on the CPU.
CIS-CRS354-48P MANAGED L3 NETWORK SWITCH
PRODUCT MANUAL
Set the System Identity
The system identity is used to identify your device on the network. Set the switch to something that can uniquely identify it.
The Identity setting can be found in the System tab in the left toolbar.
Undo/Redo
Undo and Redo buttons are located in the left toolbar. You may use them to quickly undo/redo any changes made to congu-
ration.
Show/Hide Passwords
Selecting the Hide Passwords button in the left toolbar will reveal or hide passwords related to Wi-Fi, Hotspot, and more.
CIS-CRS354-48P MANAGED L3 NETWORK SWITCH
PRODUCT MANUAL
Changing the Default Password
The default username is cis and the password is integration. After you log in for the rst time, please create a new a password
to increase the security of the device.
Rebooting the Device
CIS discourages rebooting your switches. If you are having ongoing issues with your network and suspect a reboot will help,
the Reboot option can be found under the System tab in the left toolbar. Clicking reboot will ask for conrmation before pro-
ceeding.
Setting the Clock
You can nd the Clock settings under the System tab in the left toolbar. Ensure the time zone is set correctly.
CIS-CRS354-48P MANAGED L3 NETWORK SWITCH
PRODUCT MANUAL
6. IP Addressing
The IP address is the master interface for the switch. By default, the switch is set to DHCP and will acquire an IP address. The
switch will support 172.16.1.0/24, 10.100.1.0/24, 192.168.1.0/24, and 192.168.0.0/24 networks by default. Should you require a
different network address, please contact CIS Services for assistance.
The DHCP Client tab
The DHCP Client tab will present you with the IP address assigned to the switch from your router. This interface can be enabled
or disabled by clicking on the “D” on the left column. You may view the DHCP options by clicking on the IP address.
Renewing the DHCP lease
To renew the DHCP lease for the switch, click on the entry in the DHCP client tab. click renew and the IP will populate with the
current IP on the switch.
Table des matières
Autres manuels CIS Changer
CIS
CIS CIS-NW-POE4 Manuel utilisateur
CIS
CIS CRS326-24G Manuel de service
CIS
CIS CRS112-8P Manuel utilisateur
CIS
CIS CRS354-48P Manuel utilisateur
CIS
CIS CIS-CRS328-24P Manuel utilisateur
CIS
CIS CIS-CRS112-8P Manuel utilisateur
CIS
CIS CRS354-48P Manuel utilisateur
CIS
CIS CRS326-24G Manuel utilisateur
CIS
CIS CRS328-24P Manuel utilisateur
CIS
CIS CIS-SW-POE4 Manuel utilisateur
