CIRTEX ECC3 Feuille d'instructions
ECC3
INSTALLATION GUIDELINES
EROSION PROTECTION APPLICATIONS
0800 247 839 | WWW.CIRTEX.CO.NZ
ISO: G 038 001 | DATE: MAY 2020 | VERSION 2
FOR FURTHER INFORMATION VISIT
WWW.CIRTEX.CO.NZ
CHANNEL
INSTALLATION
DETAIL
1. Dig a 150mm by 150mm trench both up-slope, down-slope, and along the top side of the
channel. Prepare the slope soil surface (raking, seeding and fertilising). Note, if used with
stormwater discharge, place the up-slope trench at the face of the discharge structure footer.
2. Begin by placing the centre blanket a minimum of 300mm down-slope of the up-slope trench.
Secure the blanket at the bottom of the trench with staples placed 300mm apart. Backll and
compact the trench. Apply seed, and fold the blanket over the soil, secure with a row of staples
placed 300mm apart across the width of the blanket (See Diagram A).
3. Roll the blanket vertically down the slope. Secure using the appropriate staple pattern below,
specied by slope. (See staple patterns).
4. Continue placing blankets up the slopes on both sides, with a minimum 100mm overlapping
(Diagram B), and securing each blanket in the beginning trench (Diagram A).
5. Additional horizontal blankets can be joined using a minimum 100mm overlapping or shingle
style in the direction of water ow. Connect the blankets by placing staples approximately
100mm apart across the width of the blankets (Diagram C).
6. For maximum performance a check slot should be placed at 8m-12m intervals. Place a row of
staples 100mm apart along the entire width of the channel. A second row should be placed
below in a staggered pattern (Diagram D).
7. The end of the blanket must be secured in a 150mm by 150mm trench by a row of staples placed
at 300mm intervals (Diagram E).
8. At the top edge of the side slope, fasten the blanket in a 150mm by 150mm trench with staples
placed at 300mm intervals. Install an additional row of staples 300mm down slope of the trench
along the width of the fabric (Diagram F).
C
F
A
FLOW
B C
DIAGRAM DIAGRAM
B
E
These guidelines are
recommendations only.
When hydroseed hydrosoil is to be used, we recommend to apply
this directly into the growing media rst, then apply the ECC3.
TIP
TO ORDER CALL US ON
0800 CIRTEX (247 839)
1. Dig a 150mm by 150mm trench both up-slope and down-slope of the area the matting is to be
applied. Prepare the slope soil surface (raking, seeding and fertilising).
2. Begin by placing the blanket a minimum of 300mm down-slope of the up-slope trench. Secure
the blanket at the bottom of the trench with staples placed 300mm apart. Backll and compact
the trench. Apply seed, and fold the blanket over soil, secure with a row of staples placed 300mm
apart across the width of the blanket (See Diagram A).
3. Roll the blanket vertically down the slope. Secure using the appropriate staple pattern below,
specied by slope (See staple patterns).
4. Parallel blankets must be overlapped by a minimum of 100mm and secured with a row of staples
approximately 1m apart (See Diagram B).
5. Additional vertical blankets can be joined using a minimum 100mm overlapping or shingle
style (See diagrams C) in the direction of the water ow. Connect the blankets by placing staples
approximately 300mm apart across the width of the blankets.
6. For maximum performance a check slot should be placed at 8m-12m intervals. Place a row of
staples 100mm apart along the entire width of the slope. A second row should be placed 100mm
below in a staggered pattern. Then continue with general installation (See diagrams D).
7. The end of blanket must be secured in a 150mm by 150mm trench with a row of staples placed at
300mm intervals (Diagram E).
SLOPE
INSTALLATION
DETAIL
FLOW
D F
DIAGRAM DIAGRAM
B
A
D
C
D
These guidelines are
recommendations only.
Installations on steep slopes will
require the correct safety gear.
WARNING
FOR FURTHER INFORMATION VISIT
WWW.CIRTEX.CO.NZ
ECC3
MATTING
ECC3
MATTING
COMPACTED
BACKFILL
15.24cm x
15.24cm
TRENCH
STEP 1. STEP 2.
DOWN-SLOPE TRENCH INSTALLATION DETAIL
STAPLE PATTERNS
SLOPES CHANNELS
150mm x
150mm
TRENCH
300mm MINIMUM OVERLAP
GRADED
DISTURBED
SLOPE
STAPLES TO BE
PLACED 300mm
ON CENTRE
STAPLES TO BE
PLACED 300mm
ON CENTRE
STAPLES TO BE
PLACED 300mm
ON CENTRE
300mm
MINIMUM
OVERLAP
COMPACTED
BACKFILL
ECC3
MATTING
UP-SLOPE TRENCH INSTALLATION DETAIL
STEP 1. STEP 2.
STAPLES TO BE
PLACED 30.48cm
ON CENTRE
1.46 staple ⁄ m
2:1 SLOPES
914mm
610mm
1.22m
0.58 staple ⁄ m
4:1 SLOPES
914mm
914mm
1.83m
3.2 staple ⁄ m
1:1 SLOPES
254mm
508mm
1.22m
2.93 staple ⁄ m
MED to HIGH FLOW
CHANNELS
508mm
610mm
1.22m
3.18 staple ⁄ m
HIGH FLOW CHANNELS
254mm
508mm
1.22m
1.0 staple ⁄ m
3:1 SLOPES
914mm
457mm
914mm
1.83m
A
DIAGRAM
E
DIAGRAM
Head Oce 16 Queen Street | Kopu
Thames 3578 | NZ
Postal Address
PO Box 470 | Thames 3540 | NZ
0800 CIRTEX (247 839)
WWW.CIRTEX.CO.NZ
CIRTEX INDUSTRIES LTD
DISCLAIMER
The information provided in this publication is correct
to the best knowledge of the company and is given
out in good faith. The information presented herein
is intended only as a general guide to the use of
such products and no liability is accepted by Cirtex
Industries Ltd for any loss or damage however arising,
which results either directly or indirectly from the
use of such information. Cirtex Industries Ltd has a
policy of continuous development so information and
product specications may change without notice.
Table des matières
Autres manuels CIRTEX Matériel agricole
Manuels Matériel agricole populaires d'autres marques
GSi
GSi PNEG-2314 Manuel utilisateur
Checchi & Magli
Checchi & Magli TEXDRIVE Manuel utilisateur
Amazone
Amazone Cenius 4003-2TX Manuel utilisateur
MASSEY FERGUSON
MASSEY FERGUSON MF 9313S Manuel utilisateur
Cima
Cima BLITZ Instructions d'utilisation et d'entretien
Amazone
Amazone CombiDisc 3000 Instructions d'installation
