Circuit-test DMS-4420 Manuel utilisateur
DMS-4420
Sound Level Meter Datalogging
CIRCUIT-TEST
CIRCUIT-TEST DMS-4420
CIRCUIT-TEST DMS-4420
DMS-4420
1
Contents
1. General Description & Specifications......1
2. Name and Functions..................................3
3. Calibration Procedures..............................6
4. Measurement Preparation.........................7
5. Operating precautions...............................7
6. Measurement..............................................8
7. System requirements................................9
8. User End Menu.........................................10
CIRCUIT-TEST DMS-4420
DMS-4420
2
To ensure proper use of this Sound Level Meter, we
recommend that you read and follow this manual
carefully.
This unit conforms to the IEC61672 Type2, ANSI S1.4
Type2 for Sound Level Meters.
This Sound Level Meter has been designed to meet the
measurement requirements of safety Engineers, Health,
Industrial safety offices and quality control in various
environments.
Ranges from 30dB to 130dB at frequencies between
31.5HZand 8 KHZ .
Display with 0.1dB steps on a 4 digits LCD.
With two equivalent weighted sound pressure levels,
A and C.
1. GENERAL DESCRIPTION &
SPECIFICATIONS
a. Display:4 digits LCD with maximum/minimum,
Resolution:0.1dB, Display Update:0.5 sec.
b. Standard applied:IEC651 Type2, ANSI1.4 Type2.
c. Frequency range:31.5Hz~8KHz.
d. Measuring level range:A Weighting 30 ~130dB.
C Weighting 35~130dB.
e. Frequency weighting:A/C.
f. Microphone:1/2 inch Electret condenser
microphone.
g. Time weighting:FAST(125mS),SLOW(1 sec).
h. Level ranges:30 ~130dB(Auto Range).
i. Accuracy: 1.5dB.
j. Dynamic range:50dB.
k. MAX/MIN:Hold readings for the Maximum and
Minimum value.
CIRCUIT-TEST DMS-4420
DMS-4420
3
l. DATA HOLD:The reading data shown on LCD can
be locked while pressing the button
m. Low Battery Indication: Replace battery as LCD
display “ ”.
n. Power Supply: 9V NEDA 1604, IEC 6F22,JIS 006P
battery×1pcs.
o. Power Life : About 50 hrs (Alkaline Battery).
p. Operating Altitude: Up to 2000M.
q. Operating temperature & Humidity: 5C~40C,
below 80%RH.
r. Storage Temperature & Humidity: -10C ~60C,
below 70%RH.
s. Dimension: 200mm(L)x55mm(W)x38mm(H).
t. Weight: About 170g. (Including batteries)
u. Accessories: Instruction manualcarrying case
9V Battery, windscreen.
CIRCUIT-TEST DMS-4420
DMS-4420
4
a. Low battery indicator
b. DATA HOLD indicator
c. Maximum indicator
d. Minimum indicator
e. A-Weighting
f. C-Weighting
g. Slow response
h. Fast response
i. REC response
j. Sound level readout
1. Windscreen
2. Display
3. HOLD button
4. Frequency weighting select
button
5. Time weighting select button
6. Maximum/Minimum hold
button
7. Backlight button
8. Power button
9. REC button
10. RS-232 Interface Connector
11. Microphone
12. Battery Cover
2. NAME AND FUNCTIONS
1. Windscreen
If operating at wind speeds over 10m/sec, please
put protective accessory windscreen in front of the
microphone.
2. Display
USB Interface Connector
CIRCUIT-TEST DMS-4420
DMS-4420
5
3. DATA HOLD button
Readings shown on the LCD can be locked while
pressing this button.
4. Frequency Weighting select button
A: A Weighting for general sound level
measurements. C: C Weighting for checking the
low-frequency content of noise.(If the C-Weighted
level is much higher than the A-weighted level,
then there is a large amount of low-frequency
noise).
5. Time weighting select button
FAST: for normal measurements. SLOW: for
checking average level of fluctuation noise.
6. MAX/MIN hold button
6.1 Press the key to activate the function. The “MAX”
symbol appears on the display and the instrument
will show the Maximum value measured and will
automatically update itself when a greater value is
measured.
6.2 Press the key again and the “MIN” symbol
appears on the display and the instrument will
show the Minimum value measured and will
automatically update itself when a lower value is
measured.
6.3 The MAX/MIN function will be disabled if the
MAX/MIN button is pressed for more than 1
second or if the meter is turned off.
CIRCUIT-TEST DMS-4420
DMS-4420
6
7. Backlight button
Press this button to enable the backlight display
for easy readings in dark environments. Press
more than 1 second to disable backlight or wait
and it will automatically turn OFF after 15
seconds.
8. Power button
Press key for 1sec to turn the sound level meter
ON or OFF. The auto power will be off
automatically after 5 minutes idle time.
9. REC button
Press the button to start recording data and press
REC again to stop recording.
The minimal interval is 1 second and the
maximum interval time is 7 Hours 59 Minutes 59
Seconds. Total Records: 14.000.
10. RS-232 Interface Connector
RS-232 interface with a computer.
11. Microphone
1/2 inch Electret Condenser microphone.
12. Battery cover
USB Interface Connector
USB interface with a computer.
CIRCUIT-TEST DMS-4420
DMS-4420
7
3. Calibration Procedures
Using a standard Acoustic Calibrator (94dB, 1KHz Sine
wave)
1. Make the button settings display: dBA
Time weighting: FAST
2. Insert the Microphone nozzle carefully into the
insertion hole of the calibrator.
3. Press the A/C and the HOLD button simultaneously
for more than 1 second and the LCD will start
blinking to confirm calibration.
4. When the LCD stops blinking, release the A/C and
Acoustic calibrator
Sound level meter
CIRCUIT-TEST DMS-4420
DMS-4420
8
the HOLD buttons. The sound level meter will
display 94.0 dBA when the calibration is done.
5. The 94 dB calibration process can be repeated until
the meter reads 94.0 dB. Recalibration cycle:1 year.
4. MEASUREMENT PREPARATION
1. Battery Loading
Remove the battery cover on the back and put in
one 9V Battery.
2. Battery Replacement
When the battery voltage is low, the following
symbol appears; this indicated that the battery
needs to be replaced.
5. OPERATING PRECAUTIONS
1. Air blowing across the microphone can cause noise
and interference when using the instrument in
windy environments, use the windscreen to reduce
noise.
2. Calibrate the instrument before operation if the
instrument was not in use for a long time or
operation at bad environment.
3. Do not store or operate the instrument in a high
temperature or high humidity environment.
4. Keep microphone dry and avoid severe vibration.
5. When the instrument is not used for an extended
period of time, remove the battery and store the unit
in a low humidity environment.
Table des matières
Autres manuels Circuit-test Instrument de mesure
Manuels Instrument de mesure populaires d'autres marques
Endress+Hauser
Endress+Hauser Proline Promag 50 Caractéristiques techniques
Siemens
Siemens SITRANS F Coriolis FCT030 Manuel de la liste des pièces
KLINGER
KLINGER CMF V Series Manuel utilisateur
EXFO
EXFO FTB-2 Manuel d'exploitation et d'entretien
Keysight
Keysight M8290A Manuel utilisateur
ADTEK
ADTEK MW-5 Manuel utilisateur