CIRCLE FITNESS M-7 SERIES E TYPE Guide de démarrage rapide
Document NO.
M-7E-EM-English
PAGE Page 1 of 25
Engineer Manual-Trouble Shooting
VERSION B
ENGINEER MANUAL FOR
AFTER SALE SERVICE
PRODUCT：TREADMILL
MODEL： M-7 SERIES E TYPE
Document NO.
M-7E-EM-English
PAGE Page 2 of 25
Engineer Manual-Trouble Shooting
VERSION B
INFORMATION GUIDE：
1. Error Signal Check Steps And Sol tions
1.1 Error Signal：『LS』 ----- Page 3~7
1.2 Error Signal：『E1』 ----- Page 8
1.3 Error Signal：『E2』 ----- Page 8~9
2. Information For Components
2.1. Interface PCB -----Page 1 ~15
2.2. Console Wire -----Page 16
2.3. Speed Sensor -----Page 17
2.4. Inverter -----Page 18
2.5. Incline Motor -----Page 18~19
2.6. Membrane Key -----Page 2
3. Engineering Mode
3.1. Engineering Mode ONE： Factory Settings ----- Page 21~22
3.2. Engineering Mode TWO： Used Information Management ----- Page 22
3.3. Engineering Mode THREE： Real Speed and Incline Parameter ----- Page 22
4. Other Information
4.1. Real Speed Do Not To Fit In With Display Speed ----- Page 23
4.2. No Any Display On Console(No Power) ----- Page 23
4.3. Abnormal Display On Console ----- Page 24
4.4. Can Not Decrease Speed ----- Page 24
4.5. Membrane Key Lose Function ----- Page 25
Document NO.
M-7E-EM-English
PAGE Page 3 of 25
Engineer Manual-Trouble Shooting
VERSION B
1. Error Signal Check Steps And Sol tions
1.1. 【LS】：Can not receive signal from speed sensor over 8 seconds while workout, all
windows display will off, all output will stop, and show 【LS】 on TIME window.
※If this is a all new product that just finished assemble, there are more possibly in
assemble problems, maybe connect wire not well or wire damaged while assemble.
1.1.1.Steps illustrate：
Step
illustrate Auxiliary Photo
1
Show【LS】 on TIME window.
2
OFF the AC power source and wait 1 seconds
then ON the AC power.
3
Press START.
4
Do the running belt moved?
A：Moved then show【LS】：Execute step 5~8
B：Did not move then show【LS】：
Execute step
9~12
C：Moved but no any error signal at all：
Execute step 13~14
？
？？
？
OFF
O
N
Document NO.
M-7E-EM-English
PAGE Page 4 of 25
Engineer Manual-Trouble Shooting
VERSION B
Step
illustrate Auxiliary Photo
5
Press STOP then press START and FAST
simultaneously immediately, to leave you
hand from keys till dot-
matrix window show
WELCOME.
6
LED display windows will do the scan mode
after show WELCOME.
After scan mode, to press ENTER till
incline window show 『15』 then
press START
to begin calibrate mode.
Document NO.
M-7E-EM-English
PAGE Page 5 of 25
Engineer Manual-Trouble Shooting
VERSION B
Step
illustrate Auxiliary Photo
Do it can be calibrate normally or show LS
on TIME window？
7
If calibrate normally and return to idle
mode, please check the SPEED para
meter on
CALORIES window when calibrate speed at
max speed 2 km/h(± .1).
In normal condition, the SPEED parameter
shall be between 34 ~35 .
If calibrate abnormal, open motor cover
and check speed sensor connected well.
If speed sensor connected well, please
replace the sensor and check again.
Refer to 2.3『Speed Sensor』
I
f still show error signal, have to check
the console wire, damage or connect
terminal problem.
I
f console wire check ok, please replace
the console wire then back to execute step
2, check the error signal disappear or not.
Refer to 2.2『Console Wire』
8
I
f still show error signal after replace
the console wire, please replace the
console PCB then back to execute step 2,
check the error signal disappear or not.
Calibrate abnormal, show 【LS】
Calibrate normal, return to idle mode
Document NO.
M-7E-EM-English
PAGE Page 6 of 25
Engineer Manual-Trouble Shooting
VERSION B
Step
illustrate Auxiliary Photo
9 Open the motor cover then ON t
he AC power,
press START to begin and check the pilot
lamp on interface PCB.
1. Is the LED7 light up before show 【LS】？
2. Is the LED6 flash before show 【LS】？
LED7 or LED6 not light or flash：
Execute
step 12~13.
LED7 light up and LED6 flash：
Execute step
1 ~11.
1 I
f LED6 & LED7 normal, have to check the
inverter first, if inverter check normal,
please replace the interface PCB then back
to execute step 2.
Refer to 2.4『Inverter』
11
Check the console wire, damage or connect
terminal problem.
After check or reconnect or replace the
wire, back to execute step 2.
Refer to 2.2『Console Wire』
12 After check or reconnect or replace the
wire but still show error signal, please
replace the console PCB then back to
execute step 2.
LED7
LED6
Document NO.
M-7E-EM-English
PAGE Page 7 of 25
Engineer Manual-Trouble Shooting
VERSION B
Step
illustrate Auxiliary Photo
13 If all function are normal and no error
signal after reset power, it maybe cause
by power core, maybe power core connect not
well, please check the power core.
If all function are normal and no error
signal after reset power, maybe the
loading is too heavy and inverter to start
the over current protect mode. I
f loading
is too heavy the motor noise will more
louder over 12km/h and running belt speed
will decreased or slippery while loading
.
P
lease maintenance or replace the running
belt and running deck.
14
On the AC power and check the fan where on
the inverter operate normal, otherwise the
inverter will over heating and to start
protect.
Refer to 2.4『Inverter』
Document NO.
M-7E-EM-English
PAGE Page 8 of 25
Engineer Manual-Trouble Shooting
VERSION B
1.2. 【E1】：When memory device damaged or read or write had program, all window display
will be off and all output will be stop and show【E1】on TIME window, show【EEPROM
ERROR】 on dot-matrix window.
1.2.1.Solution：Replace the console PCB.
1.3. 【E2】：IF incline had some problems when initial, incline can not reach the right
position, will show 『ELEVATION ERROR
ELEVATION ERRORELEVATION ERROR
ELEVATION ERROR
PRESS STOP TO BYPASS
PRESS STOP TO BYPASSPRESS STOP TO BYPASS
PRESS STOP TO BYPASS』on dot-matrix window,
press STOP to bypass the signal but incline function can not be use, if incline had
some problems when during workout, the INCLINE window will show 【E2】but other
function are normal to use.
※If this is a all new product that just finished assemble, there are more possibly in
assemble problems, maybe connect wire not well or wire damaged while assemble.
1.3.1.Steps illustrate：
Step
illustrate Auxiliary Photo
1
Open the motor cover then switch
OFF the
AC power source and wait 1 seconds then
ON the AC power.
2
Check the pilot lamps LED4 & LED5 on
interface PCB before show 【E2】.
The LED4 or LED5 light up before show E2？
Yes：Next step.
No：Check console wire connect well.
Refer to：
2.1『Interface PCB』
2.2『Console Wire』
OFF
O
N
Document NO.
M-7E-EM-English
PAGE Page 9 of 25
Engineer Manual-Trouble Shooting
VERSION B
Step
illustrate Auxiliary Photo
5
Check the console wire, damage or connect
terminal problem.
After check or reconnect or replace the
wire, back to execute step 1 to check.
Refer to 2.2『Console Wire』
6
After check or reconnect or replace the
wire but still show error signal, please
replace the incline motor or internal
variable resistor(VR)
then back to execute
step 1 to check.
Refer to 2.5『Incline Motor』
7
After replace the incline motor or
internal variable
resistor but still show
error signal, please replace the console
PCB then back to execute step 1 to check.
Document NO.
M-7E-EM-English
PAGE Page 10 of 25
Engineer Manual-Trouble Shooting
VERSION B
2. Information For Components
2.1. Interface PCB：
2.1.1.Appearance and connector description：
2.1.2.Description of pilot lamps on interface PCB：
LED2：Pilot lamp of console power, normal full light up when power ON.
LED3：Pilot lamp of decrease speed, flash when decreasing speed, switch off while
speed reached.
LED4：Pilot lamp of incline UP, light up when increase grade, switch of while
grade reached.
LED5：
Pilot lamp of incline DOWN, light up when decrease grade, switch of while
grade reached.
LED6：Pilot lamp of increase speed, flash when increasing speed, switch off while
speed reached.
LED7：Pilot lamp of enable motor, light up while work, switch off while stop.
Console wire
Speed sensor wire
Inverter control wire
Incline VR wire
AC power input
90~240Vac
Incline UP
Incline COM
Incline DOWN
Inverter AC power
LED2
LED7
LED6
LED3
LED4
LED5
U5
U2
U1
Autres manuels pour M-7 SERIES E TYPE
1
Table des matières
Autres manuels CIRCLE FITNESS tapis roulant
CIRCLE FITNESS
CIRCLE FITNESS M7 Manuel utilisateur
CIRCLE FITNESS
CIRCLE FITNESS M7 Manuel utilisateur
CIRCLE FITNESS
CIRCLE FITNESS M6 AC Manuel utilisateur
CIRCLE FITNESS
CIRCLE FITNESS M7 Manuel utilisateur
CIRCLE FITNESS
CIRCLE FITNESS Run 3.0i Manuel utilisateur
CIRCLE FITNESS
CIRCLE FITNESS M-7 SERIES E TYPE Manuel utilisateur
CIRCLE FITNESS
CIRCLE FITNESS E6 Manuel utilisateur
CIRCLE FITNESS
CIRCLE FITNESS M8 Manuel utilisateur
CIRCLE FITNESS
CIRCLE FITNESS M8 LED Manuel utilisateur
Manuels tapis roulant populaires d'autres marques
Smooth Fitness
Smooth Fitness EVO 3i Manuel utilisateur
NordicTrack
NordicTrack NETL81810.0 Manuel utilisateur
Schwinn
Schwinn 830/Journey 8.0 Manuel utilisateur
Keys Fitness
Keys Fitness HealthTrainer HT-740T Manuel utilisateur
Spirit
Spirit XT8 Manuel utilisateur
NordicTrack
NordicTrack T 14.0 Treadmill Manuel utilisateur