Christie Q Series Manuel utilisateur

Q Series Lamp Hot Swap Instruction Sheet 1

020-101356-01 Rev. 1 (03-2014)

Q Series Lamp Hot Swap

Instruction Sheet

This document provides instructions for replacing a Q Series lamp using the hot swap method.

Safety Precautions

Tools and Hardware Required

• DWU951, DWX951, and DXG1051 replacement lamp (PN: 003-004774-XX)

• #2 Phillips screwdriver

Hot Swap Procedure Timing

The hot swap procedure must be completed in three minutes or the hot swap command is canceled

and the projector shuts down. The hot swap countdown is initiated when the first lamp cover screw is

loosened. The countdown completes when the lamp door is re-attached with its two screws

tightened.

Failure to comply with these safety precautions results in death or serious injury.

• Lamp replacement must be performed by a Christie authorized service technician.

• Never attempt to remove the lamp when hot. The lamp is under a great deal of pressure

when hot and may explode, causing personal injury or death and/or property damage.

Allow the lamp to cool completely before handling.

• Always wear manufacturer approved protective safety clothing (gloves, jacket, face

shield) whenever the lamp door is open or when handling the lamp. Only qualified

technicians should install projector lamps.

• If the lamp is blown out, do not perform this procedure.

Failure to comply with these safety precautions could result in death or serious injury.

• Possibly hazardous optical radiation emitted from this product. (Risk group 3)

• Thermal radiation emitted from this product may cause burns. (Risk group 3)

• Do not insert your hand or tools into the lamp house while the lamp is removed.

Do not look straight into the ignited lamp or strongly lighted portion after the lamp is

removed. Failure to comply with this safety precaution might cause decreased vision or loss

of sight.

Q Series Lamp Hot Swap Instruction Sheet

Q Series Lamp Hot Swap Instruction Sheet 2

020-101356-01 Rev. 1 (03-2014)

Replace a Lamp Using the Hot Swap Method

1. While the lamp is on, press Function and then Zoom and hold for a minimum of three seconds.

2. From the Setup menu, press Select Lamp and press the Up or Down arrows to determine

which lamp to change.

3. To select the lamp, press the Right arrow.

The selected lamp turns off and the LED located on the back of the projector displays red.

If a lamp error has previously occurred, the lamp name needing to be replaced is displayed in the

LCD monitor. Hot swap mode is automatically selected for the lamp needing to be replaced. Both

the front and back LAMP-# LEDs display red.

4. Wait 45 minutes for the lamp to cool down.

5. When the back LAMP-#LED is solid orange, remove the two screws on the lamp cover.

Where #is the number of the lamp you are changing.

If you open the lamp door while the LED is flashing, it turns off both lamps and you receive a

COVER[open] error.

6. Remove the lamp cover.

7. Remove the three lamp screws.

8. Remove the lamp by its handle.

9. Insert the new lamp.

10. Tighten the three lamp screws.

11. Re-attach the lamp cover and tighten the two screws.

The back LAMP-#LED blinks orange. The front LAMP-#LED turns off if lit due to a previous lamp

error.

12. To reset the run time, from the Setup menu select Lamp & Filter > LAMP-#Time.

When successfully reset, the back LAMP-# LED turns off. If the LED continues to blink orange,

the lamp run time is not initializing. Refer to the Operator’s Guide for details on how to reset the

lamp run time.

13. To return to normal display in the LCD monitor, press Function.

Technical Support

North and South America: +1-800-221-8025 or [email protected]

Europe, Middle East, and Africa: +44 (0) 1189 778111 or [email protected]

Asia Pacific: tech-[email protected]

Autres manuels pour Q Series

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Christie Projecteur

Christie

Christie LW650 Manuel utilisateur

Christie

Christie Christie LW25U Manuel utilisateur

Christie

Christie Roadster S+12K Manuel utilisateur

Christie

Christie Crimson Series Manuel utilisateur

Christie

Christie Roadie HD+35K Manuel utilisateur

Christie

Christie Vivid WHITE 38-VIV401-01 Manuel utilisateur

Christie

Christie Roadster S+12K Manuel utilisateur

Christie

Christie DWU951 Manuel utilisateur

Christie

Christie CineLife+ 4 Series Manuel utilisateur

Christie

Christie Roadie HD+35K Manuel utilisateur

Christie

Christie Vivid Blue 38-VIV301-01 Manuel utilisateur

Christie

Christie CP2000-ZX Manuel utilisateur

Christie

Christie M Series Manuel utilisateur

Christie

Christie Boxer 30 Instructions de montage

Christie

Christie D4K2560 Manuel utilisateur

Christie

Christie E Series Manuel utilisateur

Christie

Christie Mirage 4K35 Manuel utilisateur

Christie

Christie CP2230 Manuel utilisateur

Christie

Christie LW600 Manuel utilisateur

Christie

Christie Boxer 4K Series Manuel utilisateur

Christie

Christie DS+305 Manuel utilisateur

Christie

Christie LX66 Manuel utilisateur

Christie

Christie GraphXMASTER DLV1400-DX Manuel utilisateur

Christie

Christie CP2220 Manuel utilisateur

Manuels Projecteur populaires d'autres marques

iEmmet

iEmmet MP-312 Manuel utilisateur

Epson

Epson VS400 Manuel utilisateur

Sony

Sony VPL-HS10 Marketing Specifications & Features Manuel utilisateur

Sony

Sony VPL-HW65ES Manuel de service

Toshiba

Toshiba TLP-791U Manuel utilisateur

Philips

Philips LC1341 Guide de référence

Panasonic

Panasonic PTL735NTU - LCD PROJECTOR-NETWORK IB Manuel utilisateur

NEC

NEC NP600S EDU Manuel utilisateur

BenQ

BenQ SH753P Manuel utilisateur

Eiki

Eiki EK-623U series Manuel utilisateur

Epson

Epson PowerLite Pro Cinema 6020UB Manuel utilisateur

Epson

Epson PowerLite Home Cinema 705HD Manuel utilisateur

Navitar

Navitar FX Manuel utilisateur

InFocus

InFocus LitePro 560 Manuel utilisateur

Sony

Sony SRX-R815P Manuel utilisateur

Vivitar

Vivitar DP1500 X Manuel utilisateur

Acer

Acer C20 Series Manuel utilisateur

Asus

Asus ZenBeam Latte Manuel utilisateur