Christie Mirage SST Instructions de montage

Installation and Setup Guide

020-102956-08

Mirage SST

NOTICES

All brand names and product names are trademarks, registered trademarks or trade names of their respective holders.

GENERAL

Every effort has been made to ensure accuracy, however in some cases changes in the products or availability could occur which may not be reflected in this

document. Christie reserves the right to make changes to specifications at any time without notice. Performance specifications are typical, but may vary

depending on conditions beyond Christie's control such as maintenance of the product in proper working conditions. Performance specifications are based on

information available at the time of printing. Christie makes no warranty of any kind with regard to this material, including, but not limited to, implied

warranties of fitness for a particular purpose. Christie will not be liable for errors contained herein or for incidental or consequential damages in connection

with the performance or use of this material. Our centers of excellence for manufacturing in Kitchener, Ontario, Canada and in Shenzhen, China are ISO

9001:2015 Quality Management System-certified.

For the most current technical documentation and office contact information, visit http://www.christiedigital.com.

Warranty

Products are warranted under Christie’s standard limited warranty, the details of which are available at https://www.christiedigital.com/help-center/

warranties/ or by contacting your Christie dealer or Christie.

PREVENTATIVE MAINTENANCE

Preventative maintenance is an important part of the continued and proper operation of your product. Failure to perform maintenance as required, and in

accordance with the maintenance schedule specified by Christie, will void the warranty.

REGULATORY

The product has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed

to provide reasonable protection against harmful interference when the product is operated in a commercial environment. The product generates, uses, and

can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio

communications. Operation of the product in a residential area is likely to cause harmful interference in which case the user will be required to correct the

interference at the user’s own expense. Changes or modifications not expressly approved by the party responsible for compliance could void the user's

authority to operate the equipment

CAN ICES-3 (A) / NMB-3 (A)

이 기기는 업무용(A급)으로 전자파적합등록을 한 기기이오니 판매자 또는 사용자는 이점을 주의하시기 바라며, 가정 외의 지역에서 사용하는 것을 목적으로 합니다.

ENVIRONMENTAL

The product is designed and manufactured with high-quality materials and components that can be recycled and reused. This symbol means that electrical

and electronic equipment, at their end-of-life, should be disposed of separately from regular waste. Please dispose of the product appropriately and according

to local regulations. In the European Union, there are separate collection systems for used electrical and electronic products.

If printing this document, consider printing only the pages you need and select the double-sided option.

Please help us to conserve the environment we live in!

Content

Introduction...................................................... 6

Important safeguards.................................................6

Safety and warning guidelines......................................... 6

Installation safety and warning guidelines..................................7

AC power precautions...............................................8

Laser safety precautions.............................................8

Light intensity hazard distance.........................................9

Third-party products...............................................13

Product labels.....................................................13

General hazards................................................. 13

Mandatory action.................................................14

Electrical labels..................................................15

Laser labels....................................................15

Additional safety hazards............................................15

Product documentation...............................................16

Related documentation.............................................16

Technical support...................................................16

Projector overview..................................................17

Contact your dealer.................................................17

Key features......................................................17

How the projector works..............................................18

List of components..................................................18

Chiller and laser illumination source components...............................18

Installation and setup..............................................19

Site requirements.................................................. 19

Physical operating environment........................................19

Power connection................................................ 19

Projector components................................................20

IR/wired remote keypad..............................................22

Display panel components.............................................24

Workflow: Installing and setting up the Mirage SST system........................ 24

Setting up the projector head...........................................26

Leveling the projector..............................................26

Mirage SST Installation and Setup Guide 3

020-102956-08 Rev. 1 (09-2022)

If printed, please recycle this document after use.

Installing the projector lens..........................................27

Connecting the projector head to AC power................................ 28

Setting up the laser illumination source.....................................28

Installing the J33 terminal block on the laser illumination source...................29

Protecting the fiber connector.........................................30

Connecting the fiber optic cable to the projector through the curved strain relief.........33

Connecting the fiber optic cable to the projector through the straight strain relief.........35

Connecting the Ethernet cable to the projector..............................38

Setting up the chiller unit............................................. 39

Performing initial system start-up........................................ 40

Turning on the system............................................. 42

Turning off the system............................................. 45

Projector LED status indicators........................................46

Projector LED shutter indicators....................................... 47

Calibrating the lens motor.............................................47

Removing the projection lens.........................................47

Aligning the image..................................................48

Selecting a test pattern.............................................49

Adjusting offset..................................................49

Adjusting boresight............................................... 49

Adjusting the fold mirror............................................51

Optimizing the integrator zoom and focus................................. 53

Adjusting DMD convergence..........................................55

Aligning the image with lens zoom and focus............................... 56

Running Auto Setup to optimize display settings............................. 56

Configuring Mirage SST to work with Christie Link.............................. 57

Disposing of the product packaging....................................... 57

Connecting devices and establishing communication.....................58

IMXB ports.......................................................58

Connecting a video source using 3G input card................................59

Connecting a video source using DVI...................................... 59

Connecting a video source using DisplayPort..................................60

Connecting a video source using HDMI.....................................60

Connecting a video source using HBMIC.................................... 60

Connecting a video source using TSIC......................................60

Selecting a video source..............................................61

Connecting to a computer or server.......................................61

Configuring the RS232 port............................................ 62

Content

Mirage SST Installation and Setup Guide 4

020-102956-08 Rev. 1 (09-2022)

If printed, please recycle this document after use.

Setting up the Ethernet...............................................62

3D setup........................................................63

3D requirements...................................................63

Hardware requirements.............................................63

Software and content requirements.....................................63

3D system timing.................................................. 64

3D input video configurations...........................................64

Setting up a single projector to display 3D content..............................64

Enabling 3D mode................................................64

Confirming the emitter setup......................................... 65

Configuring the projector for the 3D source................................ 65

Connecting devices to the 3D sync ports....................................65

Regulatory...................................................... 67

Safety......................................................... 67

Electro-magnetic compatibility.......................................... 67

Emissions..................................................... 67

Immunity..................................................... 67

Environmental.................................................... 67

Signal connectivity specifications for ................................. 69

HBMIC video formats................................................69

TSIC video formats................................................. 71

QDPIC video formats................................................ 71

TDPIC video formats................................................ 72

DDIC video formats.................................................72

THIC video formats................................................. 73

3GIC video formats.................................................73

Dual-input 3D and HFR 2D.............................................74

Content

Mirage SST Installation and Setup Guide 5

020-102956-08 Rev. 1 (09-2022)

If printed, please recycle this document after use.

Introduction

This manual is intended for professionally trained operators of Christie high-brightness projection

systems.

The illustrations in this document are for representation only and may not depict your projector model

exactly.

Only Christie qualified technicians who are knowledgeable about the hazards associated with laser use,

high-voltage, and the high temperatures generated by the projector lasers are authorized to

assemble, install, and service the projector.

For complete Mirage SST product documentation and technical support, go to www.christiedigital.com.

Important safeguards

To prevent personal injury and to protect the device from damage, read and follow these safety

precautions. This projector is intended for use in a non-cinema environment.

Safety and warning guidelines

Read all safety and warning guidelines before installing or operating the projector.

This projector is intended for use in a fixed install environment (also known as a cinema environment).

This projector must be operated in an environment that meets the operating range specification. Use

only the attachments and/or accessories recommended by Christie. Use of others may result in the

risk of fire, shock, or personal injury.

Warning! If not avoided, the following could result in death or serious injury.

• This product must be operated in an environment that meets the operating range as specified in

this document.

• Do not look directly into the lens when the light source is on. The extremely high brightness can

cause permanent eye damage.

• ELECTRICAL and BURN HAZARD! Use caution when accessing internal components.

• FIRE HAZARD! Keep hands, clothes, and all combustible material away from the concentrated

light beam of the projector.

• Keep fingers and other body parts away from the moving parts in the product. Tie back long

hair, and remove jewelry and loose clothing before manually adjusting the product.

• FIRE AND SHOCK HAZARD! Use only the attachments, accessories, tools, and replacement parts

specified by Christie.

• Do not operate the product without a lens installed.

• Always use a lens plug when installing or moving the product. This prevents contaminants from

entering the product.

• RADIATION HAZARD! Use of controls or adjustments, or performing procedures other than those

specified may result in hazardous radiation exposure.

Mirage SST Installation and Setup Guide 6

020-102956-08 Rev. 1 (09-2022)

If printed, please recycle this document after use.

Caution! If not avoided, the following could result in minor or moderate injury.

• TRIP OR FIRE HAZARD! Position all cables where they cannot contact hot surfaces, be pulled, be

tripped over, or damaged by persons walking on or objects rolling over the cables.

Installation safety and warning guidelines

Read all safety and warning guidelines before installing the projector.

Warning! If not avoided, the following could result in death or serious injury.

• Possible hazardous optical radiation emitted from this product. (Risk group 3)

• Christie products must be installed and serviced by Christie qualified technicians.

• Do not operate the product without all of its covers in place.

• A minimum of two people or appropriately rated lift equipment is required to safely lift, install,

or move the product.

• Always install safety straps when the frame and projector are installed overhead.

• Observe load ratings and applicable local safety codes.

• When installing the projector in portrait mode, the rigging device must have a sufficient load

rating, as identified in this manual.

•

• This product must be installed within a restricted access location not accessible by the general

public.

• Install the product so users and the audience cannot enter the restricted area at eye level.

• Only personnel who are trained on the precautions for the restricted access location can be

granted entry to the area.

• Only Christie qualified technicians are permitted to open product enclosures.

Caution! If not avoided, the following could result in minor or moderate injury.

• ELECTRICAL and BURN HAZARD! Use caution when accessing internal components.

• Only Christie qualified technicians are authorized to use the tools provided in the toolbox.

Introduction

Mirage SST Installation and Setup Guide 7

020-102956-08 Rev. 1 (09-2022)

If printed, please recycle this document after use.

AC power precautions

Read all safety and warning guidelines before connecting to AC power.

Warning! If not avoided, the following could result in death or serious injury.

• SHOCK HAZARD! Only use the AC power cord provided with the product or recommended by

Christie.

• FIRE AND SHOCK HAZARD! Do not attempt operation unless the power cord, power socket, and

power plug meet the appropriate local rating standards.

• SHOCK HAZARD! Do not attempt operation if the AC supply is not within the specified voltage

and current, as specified on the license label.

• SHOCK HAZARD! The AC power cord must be inserted into an outlet with grounding.

• SHOCK HAZARD! A dedicated, protected ground or earth wire must be installed on the product

by Christie qualified technicians or electricians before it can be connected to power.

• SHOCK HAZARD! Disconnect the product from AC before installing, moving, servicing, cleaning,

removing components, or opening any enclosure.

• Install the product near an easily accessible AC receptacle.

Caution! If not avoided, the following could result in minor or moderate injury.

• FIRE HAZARD! Do not use a power cord, harness, or cable that appears damaged.

• FIRE OR SHOCK HAZARD! Do not overload power outlets and extension cords.

• SHOCK HAZARD! Power supply uses double pole/neutral fusing. Disconnect all power sources

before opening the product.

Laser safety precautions

Read all safety and warning guidelines before operating the projector laser.

Warning! If not avoided, the following could result in death or serious injury.

• PERMANENT/TEMPORARY BLINDNESS HAZARD! No direct exposure to the beam must be

permitted. Class 1 Laser Product - Risk Group 3 according to IEC 60825-1:2014 and IEC

62471-5:2015.

• LASER RADIATION HAZARD! This projector has an external Class 4 laser module. Never attempt

to disassemble or modify the laser module.

• Possible hazardous optical radiation emitted from this product. (Risk group 3)

• Only Christie qualified technicians who are knowledgeable about the hazards associated with

laser use, high-voltage, and high temperatures generated by the product are authorized to

assemble, install, and service the Christie Laser Projection System.

• RADIATION HAZARD! Use of controls or adjustments, or performing procedures other than those

specified may result in hazardous radiation exposure.

• Do not look directly into the lens when the light source is on. The extremely high brightness can

cause permanent eye damage.

• Do not operate the product without all of its covers in place.

• LASER RADIATION! Do not short the contact rings.

• Always keep a protective cap on disconnected fiber optic cables.

Introduction

Mirage SST Installation and Setup Guide 8

020-102956-08 Rev. 1 (09-2022)

If printed, please recycle this document after use.

Light intensity hazard distance

This projector has been classified as Risk Group 3 as per the IEC 62471-5:2015 standard due to

possible hazardous optical and thermal radiation being emitted.

Warning! If not avoided, the following could result in serious injury.

• PERMANENT/TEMPORARY BLINDNESS HAZARD! No direct exposure to the beam must be

permitted. Class 1 Laser Product - Risk Group 3 according to IEC 60825-1:2014 and IEC

62471-5:2015.

• PERMANENT/TEMPORARY BLINDNESS HAZARD! Operators must control access to the beam

within the hazard distance or install the product at the height that prevents exposure of

spectators' eyes within the hazard distance. The hazard zone must be no lower than 3.0 meters

above the floor and the horizontal clearance to the hazard zone must be a minimum 2.5 meters.

• EXTREME BRIGHTNESS! Do not place reflective objects in the product light path.

The following show the zones for ocular and skin hazard distances.

• A—Hazard zone. The region of space where the projection light from the laser-illuminated

projector is above emission limits for Risk Group 2. The light intensity may cause eye damage

after a momentary or brief exposure (before a person can avert his or her eyes away from the

light source). The light may cause skin burns to occur.

• B—Hazard distance. Operators must control access to the beam within the hazard distance or

install the product preventing potential exposure of the spectators' eyes from being in the

hazard distance.

• C—No access zone. Horizontal clearance of the no access zone must be a minimum of 2.5

meters.

• D—Vertical distance to hazard zone. The hazard zone must be no lower than 3.0 meters above

the floor.

If the vertical distance to hazard zone requirement (Zone D) is satisfied, the horizontal

clearance distance (Zone C) is not needed.

• E—Represents the top view of the projector.

• F—Represents the side view of the projector.

Introduction

Mirage SST Installation and Setup Guide 9

020-102956-08 Rev. 1 (09-2022)

If printed, please recycle this document after use.

The following table lists the hazard distance for the Christie projector lens with the zoom adjusted to

its most hazardous position.

For US and international hazard distances based upon IEC 62471-5:2015, Photobiological Safety of

Lamps and Lamp Systems – Part 5: Image Projectors.

Projection lens Part number Hazard distance (m)

Type A* Types B, C, D, E*

High brightness (HB) lenses

0.38:1 4K enhanced 144-136101-XX 1.0 1.0

0.72:1 HB fixed 144-110103-XX 1.0 1.0

0.9:1 fixed lens 144-111014-XX 1.2 1.0

1.13-1.31:1 HB zoom

(Discontinued)

144-103105-XX 1.6 1.4

1.13-1.66:1 HB zoom 144-129103-XX 2.1 1.8

1.31-1.63:1 HB zoom 144-104106-XX 2.1 1.8

1.45-2.17:1 HB zoom 144-130105-XX 2.8 2.5

1.63-2.17:1 HB zoom

(Discontinued)

144-105107-XX 2.7 2.4

1.95-3.26:1 HB zoom 144-131106-XX 4.1 3.6

1.99-2.71:1 HB zoom 144-106108-XX 3.4 3.0

2.71-3.89:1 HB zoom 144-107109-XX 4.8 4.3

3.89-5.43:1 HB zoom 144-108100-XX 7.0 6.0

4.98-7.69:1 HB zoom 144-109101-XX 9.9 8.6

Ultra high contrast (UHC) lenses

0.72:1 UHC fixed 163-116109-XX 1.0 1.0

0.9:1 UHC fixed 163-117100-XX 1.0 1.0

1.13-1.66 UHC zoom 163-118101-XX 1.7 1.6

1.45-2.17 UHC zoom 163-119102-XX 2.3 2.1

1.95-3.26 UHC zoom 163-120103-XX 3.4 3.1

2.71-3.89 UHC zoom 163-121105-XX 3.8 3.6

3.89-5.43 UHC zoom 163-122106-XX 5.4 5.1

* For specific Christie-supplied model names and part numbers, refer to the Mirage SST Projector

Head Specifications Guide (P/N: 020-102994-XX).

Type A 168-1011XX-XX

Type B 168-1061XX-XX

Type C 168-1071XX-XX

Type D 168-1081XX-XX

Introduction

Mirage SST Installation and Setup Guide 10

020-102956-08 Rev. 1 (09-2022)

If printed, please recycle this document after use.

Autres manuels pour Mirage SST

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Christie Projecteur

Christie

Christie LHD700 Manuel utilisateur

Christie

Christie CP2308-G Instructions de montage

Christie

Christie DWU1612-HS Manuel d'utilisation et d'entretien

Christie

Christie CP2000-ZX Manuel utilisateur

Christie

Christie DS+60 Manuel utilisateur

Christie

Christie LX45 Manuel utilisateur

Christie

Christie Cinema 4K-RGB CP4315-RGB Manuel utilisateur

Christie

Christie CineLife+ CP4415-RGB Instructions de montage

Christie

Christie RPMSP-D120U Instructions d'installation et d'utilisation

Christie

Christie CP2308 Manuel utilisateur

Christie

Christie Matrix 3500 Manuel utilisateur

Christie

Christie H Series Manuel utilisateur

Christie

Christie CP4220 Manuel utilisateur

Christie

Christie 38-VIV212 Manuel utilisateur

Christie

Christie TPC-60 Manuel utilisateur

Christie

Christie LWU505 Manuel utilisateur

Christie

Christie CP2208 Manuel utilisateur

Christie

Christie Griffyn Series Instructions de montage

Christie

Christie Solaria CP2210 Manuel utilisateur

Christie

Christie DS Series Manuel utilisateur

Christie

Christie Roadster X9 Manuel utilisateur

Christie

Christie DCP-H Manuel utilisateur

Christie

Christie 4K10-HS Instructions de montage

Christie

Christie Christie LW25U Manuel utilisateur

Manuels Projecteur populaires d'autres marques

iEmmet

iEmmet MP-312 Manuel utilisateur

Epson

Epson VS400 Manuel utilisateur

Sony

Sony VPL-HS10 Marketing Specifications & Features Manuel utilisateur

Sony

Sony VPL-HW65ES Manuel de service

Toshiba

Toshiba TLP-791U Manuel utilisateur

Philips

Philips LC1341 Guide de référence

Panasonic

Panasonic PTL735NTU - LCD PROJECTOR-NETWORK IB Manuel utilisateur

NEC

NEC NP600S EDU Manuel utilisateur

BenQ

BenQ SH753P Manuel utilisateur

Eiki

Eiki EK-623U series Manuel utilisateur

Epson

Epson PowerLite Pro Cinema 6020UB Manuel utilisateur

Epson

Epson PowerLite Home Cinema 705HD Manuel utilisateur

Navitar

Navitar FX Manuel utilisateur

InFocus

InFocus LitePro 560 Manuel utilisateur

Sony

Sony SRX-R815P Manuel utilisateur

Vivitar

Vivitar DP1500 X Manuel utilisateur

Acer

Acer C20 Series Manuel utilisateur

Asus

Asus ZenBeam Latte Manuel utilisateur