Christie I Series Manuel utilisateur

Coolant Refill Instruction Sheet 1 of 9

020-100686-01 Rev. 1 (03-2011)

Coolant Refill

Instruction Sheet

INTRODUCTION

The following procedure should be performed whenever the coolant system needs to be refilled.

NOTICE: Never allow the pump to run dry to avoid damaging it.

KITS REQUIRED

• #003-001837-xx Coolant Refill Kit (includes JeffCool E105 jug of coolant, refill bottle, funnel, MSDS sheet)

INSTRUCTIONS

SERIES I

Series 1 projectors include the CP2000-S/-SB/-h/-i/-X/-XB/-Z/-M/-MR and the Roadie 25K/HD+30K/

HD+35K. For details on how to flush the coolant system on these models refer to, Roadie 25K/

HD+30K/HD+35K, CP2000-S/-SB/-h/-i/-X/-XB/-M/-MR/-ZX Coolant Flush Instruction Sheet

(P/N: 020-100179-03).

CP2000-S/-SB/-H/-I/-X/-XB AND ROADIE 25K/D+30K/HD+35K

ACCESS COOLING SYSTEM

1. Remove the projector lid. On the Roadie 25K/HD+30K/HD+35K or CP2000-X/-XB, open the

igniter door (Figure 1, left). On a CP2000-S/-SB/-i/-h (Figure 1, right), open the non-operator

side pedestal door and skip to Step 3.

Figure 1 Access Cooling System

2 of 9 Coolant Refill Instruction Sheet

020-100686-01 Rev. 1 (03-2011)

2. On the CP2000-X/-XB or Roadie 25K/HD+30K/HD+35K, remove the center (8 screws) and front

belly pan (4 screws), as shown in Figure 2.

Figure 2 Remove Belly Pans

3. Prime/Purge of Air: Power up the projector (no lamp). Manipulate or “prime” all coolant hoses

by flicking, pinching and raising them as necessary (Figure 3) to keep liquid moving and flowing

to-and-from the pump. You must purge the system of all air, otherwise the coolant will not flow

properly and may cause the DMDs to overheat. NOTE: The coolant in the reservoir disappears

into the system immediately after the pump has been started. You must continually refill the

reservoir until the coolant level stops falling.

CAUTION! Purge all hoses of air! On CP2000-X/-XB and Roadie 25K/HD+30K/

HD+35K, check hoses in belly pan area.

Figure 3 Refill the System & Prime

all Hoses to Eliminate Air Locks

Coolant Refill Instruction Sheet 3 of 9

020-100686-01 Rev. 1 (03-2011)

4. Continue running the projector (no lamp), topping up the reservoir as you eliminate more and

more air pockets from all coolant hoses (Figure 4).

TIPS:

• Watch for air near all hose fittings.

• Tiny or large bubbles indicates air present.

Continue priming (shake hose, etc).

• Solid, opaque hoses with no bubbles indicates

system is primed and ready for use.

5. Power down. Make sure reservoir is approximately

1/2 - 3/4 full, topping up as necessary. In the

CP2000-S/-SB/-i/-h, double-check level through

the viewing gauge on the pedestal door.

6. When you are certain that all air is purged, replace

the reservoir cap, belly pan, igniter door and

projector lid.

7. Power up and test.

CP2000-M/MR

ACCESSING THE COOLING SYSTEM

1. Turn the projector lamp OFF. Wait at least 10 minutes to allow for proper cooling to take place.

2. Turn power OFF from the Control Display Panel (CDP).

3. Remove the top lid:

a. Use a #2 Phillips™ to loosen the 7 captive screws securing the top lid to the projector housing

(Figure 5).

Figure 5 Remove Top Lid

b. Unlock the rear access door using the low security key.

c. Lift the lid up from the rear of the projector and pull it away from the 2 tabs on the front skin.

NOTE: When installing, align the front 2 tabs and reverse the above steps.

Figure 4 Check all Coolant Hoses

for Air Bubbles

4 of 9 Coolant Refill Instruction Sheet

020-100686-01 Rev. 1 (03-2011)

CP2000-S/-SB/-H/-I/-X/-XB/-M/-MR AND ROADIE 25K/D+30K/HD+35K

FILLING THE RESERVOIR

1. Loosen the top screw (Figure 6) and use the fill bottle to add coolant. Power up the projector and

continue adding coolant so the fluid level does not drop below the Minimum Fill Line.

Figure 6 Fill the Reservoir

(Reservoir for CP2210, CP2220 and CP2230 shown)

2. Air Bubble Impeding Flow: If the liquid in the reservoir does not move due to air bubbles,

remove the entire fan pack and pump section. For instructions, refer to the CP2000-M/MR

Service Manual (P/N: 020-100124-xx). Tilt the pump at different angles until the coolant starts to

flow.

Coolant Refill Instruction Sheet 5 of 9

020-100686-01 Rev. 1 (03-2011)

CP2000-ZX

ACCESSING THE COOLING SYSTEM

1. Turn the projector lamp OFF. Wait at least 10 minutes to allow for proper cooling to take place.

2. Turn power OFF from the Touch Panel Controller (TPC).

3. Unlock the front lid using the high security key. Raise the lid and slide it out from the opposite side

(Figure 7).

Figure 7 Remove Front Top Lid

4. Remove the PCM cover by pushing on the tab at the top of the cover. Tilt the cover slightly then

lift enough to clear the tabs at the bottom and remove (Figure 8).

5. Remove the air filter cover by releasing the 2 tabs on the air filter cover, lift and remove

(Figure 8).

Figure 8 Remove PCM and Air Filter Covers

6 of 9 Coolant Refill Instruction Sheet

020-100686-01 Rev. 1 (03-2011)

6. Use a #2 Phillips™ to remove the 2 screws on the security bracket (above cardcage), which

secures the liquid cooling panel (Figure 9).

Figure 9 Remove Security Bracket

7. Remove the 4 screws securing the access panel frame, which is located on the input side of the

projector (Figure 10).

Figure 10 Remove Access Panel Frame

Coolant Refill Instruction Sheet 7 of 9

020-100686-01 Rev. 1 (03-2011)

8. Remove the 5 screws securing the liquid cooling panel. Four of these screens are on the panel and

one is located along the bottom of the panel (Figure 11). Swing the panel out and hang it on the

screws located on the frame.

Figure 11 Remove Liquid Cooling Panel

9. Fill the reservoir with coolant. NOTE: The reservoir only holds 1/2 of the required coolant for the

system.

10. Power the pump ON and watch the coolant begin

circulating. Keep adding coolant into the reservoir as

needed to prevent the fluid level from dropping below the

Minimum Fill Line. Continue running the system until the

coolant appears free from air bubbles.

Figure 12 Fill Reservoir

8 of 9 Coolant Refill Instruction Sheet

020-100686-01 Rev. 1 (03-2011)

SERIES II

Series 2 projectors include the CP2210, CP2220 and CP2230 models. For detailed information on

flushing the coolant system, refer to the CP2210, CP2220 and CP2230 Coolant Flush Instruction

Sheet (P/N: 020-100685-xx).

CP2210

ACCESSING THE COOLING SYSTEM

1. Power the projector lamp OFF. Wait for at least 10 minutes to allow for proper cooling to take

place before powering the projector OFF, via the TPC.

2. Use a #2 Phillips™to loosen the 7 captive screws securing the top lid to the projector housing

(Figure 13).

Figure 13 Remove Top Lid

3. Unlock the rear access door using the low security key. Lift the lid up from the rear of the projector

and pull it away from the 2 tabs on the front skin.

Coolant Refill Instruction Sheet 9 of 9

020-100686-01 Rev. 1 (03-2011)

CP2220 AND CP2230

ACCESSING THE COOLING SYSTEM

1. Turn the projector lamp OFF. Wait at least 10 minutes to allow for proper cooling to take place

before powering down the projector, via the TPC.

2. Unlock the front lid using the low security key provided. Lift the lid up and remove (Figure 14).

Figure 14 Remove Front Top Lid

CP2210, CP2220 AND CP2230

FILLING THE RESERVOIR

1. Loosen the top screw (Figure 15) and use the fill bottle provided to add coolant.

2. Power the projector ON and continue adding coolant until the fluid level does not drop below the

Minimum Fill Line.

3. Continue running the system until the coolant appears free from air bubbles.

Figure 15 Fill Reservoir

(Reservoir for CP2210, CP2220 and CP2230 shown)

Low Security Key

Ce manuel convient aux modèles suivants

Autres manuels Christie Projecteur

Christie

Christie RPMX-D120U Manuel utilisateur

Christie

Christie LX1000 Manuel utilisateur

Christie

Christie CP2309-RGB Manuel utilisateur

Christie

Christie 38-VIV402-01 Manuel utilisateur

Christie

Christie 38-VIV211-01 Manuel utilisateur

Christie

Christie Matrix 3000 Manuel utilisateur

Christie

Christie IMB Manuel utilisateur

Christie

Christie Roadster S+12K Mode d’emploi

Christie

Christie Mirage HD25 Manuel utilisateur

Christie

Christie LWU701i Manuel utilisateur

Christie

Christie CP2220 Manuel utilisateur

Christie

Christie HS 2K Series Manuel utilisateur

Christie

Christie CP2000 Manuel utilisateur

Christie

Christie 103-002001 Manuel utilisateur

Christie

Christie DWU1052 Manuel utilisateur

Christie

Christie LHD700 Manuel utilisateur

Christie

Christie APS Series Manuel utilisateur

Christie

Christie CP2208 Guide de l'utilisateur

Christie

Christie APS Series Manuel utilisateur

Christie

Christie Cinema 4K-RGB CP4325-RGB Manuel utilisateur

Christie

Christie LWU620i Manuel utilisateur

Christie

Christie 1000W J Series Manuel utilisateur

Christie

Christie Roadster Manuel utilisateur

Christie

Christie DWU1052 Manuel utilisateur

Manuels Projecteur populaires d'autres marques

iEmmet

iEmmet MP-312 Manuel utilisateur

Epson

Epson VS400 Manuel utilisateur

Sony

Sony VPL-HS10 Marketing Specifications & Features Manuel utilisateur

Sony

Sony VPL-HW65ES Manuel de service

Toshiba

Toshiba TLP-791U Manuel utilisateur

Philips

Philips LC1341 Guide de référence

Panasonic

Panasonic PTL735NTU - LCD PROJECTOR-NETWORK IB Manuel utilisateur

NEC

NEC NP600S EDU Manuel utilisateur

BenQ

BenQ SH753P Manuel utilisateur

Eiki

Eiki EK-623U series Manuel utilisateur

Epson

Epson PowerLite Pro Cinema 6020UB Manuel utilisateur

Epson

Epson PowerLite Home Cinema 705HD Manuel utilisateur

Navitar

Navitar FX Manuel utilisateur

InFocus

InFocus LitePro 560 Manuel utilisateur

Sony

Sony SRX-R815P Manuel utilisateur

Vivitar

Vivitar DP1500 X Manuel utilisateur

Acer

Acer C20 Series Manuel utilisateur

Asus

Asus ZenBeam Latte Manuel utilisateur