CHIEF PSS2000 Manuel utilisateur

INSTALLATION INSTRUCTIONS

PLASMA SWIVEL STAND

Spanish Product Description

German Product Description

Portuguese Product Description

Italian Product Description

Dutch Product Description

French Product Description

PSS2000

PSS2000 Installation Instructions

DISCLAIMER

Milestone AV Technologies and its affiliated corporations and

subsidiaries (collectively "Milestone"), intend to make this

manual accurate and complete. However, Milestone makes no

claim that the information contained herein covers all details,

conditions or variations, nor does it provide for every possible

contingency in connection with the installation or use of this

product. The information contained in this document is subject

to change without notice or obligation of any kind. Milestone

makes no representation of warranty, expressed or implied,

regarding the information contained herein. Milestone assumes

no responsibility for accuracy, completeness or sufficiency of

the information contained in this document.

Chief® and ClickConnect™ are registered trademarks of

IMPORTANT WARNINGS AND

CAUTIONS!

WARNING:

A WARNING alerts you to the possibility of

serious injury or death if you do not follow the instructions.

CAUTION:

A CAUTION alerts you to the possibility of

damage or destruction of equipment if you do not follow the

corresponding instructions.

WARNING:

Failure to read, thoroughly understand, and

follow all instructions can result in serious personal injury,

damage to equipment, or voiding of factory warranty! It is the

installer’s responsibility to make sure all components are

properly assembled and installed using the instructions

provided.

WARNING:

Failure to provide adequate structural strength

for this component can result in serious personal injury or

damage to equipment! It is the installer’s responsibility to

make sure the structure to which this component is attached

can support five times the combined weight of all equipment.

Reinforce the structure as required before installing the

component.

WARNING:

Exceeding the weight capacity can result in

serious personal injury or damage to equipment! It is the

installer’s responsibility to make sure the combined weight of

all components located on the PSS2000 does not exceed

150 lbs (68.04 kg).

DIMENSIONS

.78

14.25

362

1.22

16.27

413 1.14

APPROXIMATE

CENTER OF DISPLAY

TOP MOUNTING BUTTON ON

PSB-XXXX DRAWING GOES HERE

45°

NOTE: CUSTOM INTERFACE BRACKET

NOT SHOWN. THE CUSTOM INTERFACE

BRACKET NEEDED FOR YOUR DISPLAY

WILL ADD BETWEEN 1/2" AND 2" IN DEPTH

AND MAY AFFECT LOCATION OF DISPLAY

ON THE MOUNT.

SEE PSB-XXXX DRAWING ALSO.

2.50

3.16

80 9.29

236

MAX 27.47

MIN 20.72

Installation Instructions PSS2000

LEGEND

Tighten Fastener

Apretar elemento de fijación

Befestigungsteil festziehen

Apertar fixador

Serrare il fissaggio

Bevestiging vastdraaien

Serrez les fixations

Loosen Fastener

Aflojar elemento de fijación

Befestigungsteil lösen

Desapertar fixador

Allentare il fissaggio

Bevestiging losdraaien

Desserrez les fixations

Phillips Screwdriver

Destornillador Phillips

Kreuzschlitzschraubendreher

Chave de fendas Phillips

Cacciavite a stella

Kruiskopschroevendraaier

Tournevis à pointe cruciforme

Open-Ended Wrench

Llave de boca

Gabelschlüssel

Chave de bocas

Chiave a punte aperte

Steeksleutel

Clé à fourche

By Hand

A mano

Von Hand

Com a mão

A mano

Met de hand

À la main

Hex-Head Wrench

Llave de cabeza hexagonal

Sechskantschlüssel

Chave de cabeça sextavada

Chiave esagonale

Zeskantsleutel

Clé à tête hexagonale

Pencil Mark

Marcar con lápiz

Stiftmarkierung

Marcar com lápis

Segno a matita

Potloodmerkteken

Marquage au crayon

Drill Hole

Perforar

Bohrloch

Fazer furo

Praticare un foro

Gat boren

Percez un trou

Adjust

Ajustar

Einstellen

Ajustar

Regolare

Afstellen

Ajuster

Remove

Quitar

Entfernen

Remover

Rimuovere

Verwijderen

Retirez

Optional

Opcional

Optional

Opcional

Opzionale

Optie

En option

Security Wrench

Llave de seguridad

Sicherheitsschlüssel

Chave de segurança

Chiave di sicurezza

Veiligheidssleutel

Clé de sécurité

PSS2000 Installation Instructions

TOOLS REQUIRED FOR INSTALLATION

PARTS

1/2" (12.7mm)

A (1)

B (5)

C (1)

3/16" D (1)

5/32"

Installation Instructions PSS2000

INSTALLATION

NOTE:

For free-standing applications only, install five rubber

bumpers (B) onto bottom of stand (A). (See Figure 1)

Figure 1

Stand Assembly

NOTE:

PSS2000 ships assembled for displays 30" in height or

less, and lowered to its minimum height.

Display Height 30 Inches or Smaller

1. Loosen the four height adjustment screws and raise the

slide with faceplate to its maximum height. (See Figure 2)

2. Raise slide to the maximum height.

3. Secure slide in place by tightening the four height

adjustment screws. (See Figure 2)

Figure 2

Display Height Greater Than 30 Inches

1. Remove slide from base by removing four button head cap

screws and four flat washers. (See Figure 3)

2. Remove faceplate from slide by removing two flat washers

and two lock nuts. (See Figure 3)

Figure 3

(B) x 5

(A)

x 4

x 2

PSS2000 Installation Instructions

3. Install faceplate into upper mounting holes of slide using

two flat washers and two lock nuts removed in Step 2.

4. Install slide onto base using four button head cap screws

and four flat washers removed in Step 1.

NOTE:

Do NOT fully tighten slide mounting screws at this time.

5. Raise slide to maximum height.

6. Tighten four height adjustment screws. (See Figure 2)

Site Preparation

WARNING:

EXCEEDING WEIGHT CAPACITY CAN

RESULT IN SERIOUS PERSONAL INJURY OR DAMAGE

TO EQUIPMENT! It is the installer’s responsibility to make

sure the combined weight of all components does not exceed

150 lbs (68.04 kg).

CAUTION:

TURNING DISPLAY CAN CAUSE DAMAGE

TO SURROUNDING OBJECTS. Make certain location

provides enough area for the display to rotate + 45° without

being obstructed.

NOTE:

See Display Stop Location Adjustment section for

information on adjusting rotation.

1. Locate a flat dry surface on which to mount the PSS2000

assembly.

2. Measure the hole locations on bottom of PSS2000 and

mark the four mounting hole locations on mounting surface.

(See Figure 4)

Figure 4

3. Drill four 1/4" diameter holes through mounting surface at

marks.

4. Secure mount to mounting surface using four 1/4-20 cap

screws with a length equal to the thickness of the mounting

surface Aplus 3/4". (See Figure 4)

Display Installation

The following procedure assumes that the proper interface

bracket for the display being mounted has already been

installed on the display.

If no interface bracket is present on display, install bracket to

display using the instructions included with the interface bracket

before proceeding.

If an interface bracket for the display being mounted needs to

be obtained, or additional assistance is required, contact Chief.

To install the display:

1. While supporting both sides of display, align four mounting

buttons on display or interface bracket with four mounting

holes in faceplate.

2. Lower display into place listening for audible "click" to

ensure recessed area of mounting buttons are properly

seated in lower area of mounting holes and ClickConnect

mechanism has engaged. (See Figure 1)

NOTE:

Holes are provided in the faceplate for use with a

padlock orsimilarlockingdevice,ifdesired.Inaddition,

the pin and nut may be removed from the upper holes

and moved to the lower holes for use as a more

permanent locking device.

Figure 5

x 4

PSS2000

3/4"

x 4

To use as a more

permanent lock,

remove pin and

nuts and

move to

lower holes.

A padlock or bolt may be

placed through latch holes

Installation Instructions PSS2000

Stand Adjustment

Adjusting Display Height

CAUTION:

DO NOT ALLOW DISPLAY TO DROP TO

BOTTOM OF STAND. Displays are fragile and may be

damaged.

1. Hold display in place and loosen the four height adjustment

screws. (See Figure 2)

2. Position display to the desired height.

3. Tighten the four height adjustment screws. (See Figure 2)

Adjusting Stand Tension

1. Check swivel tension while display is attached to the stand.

2. If tension adjustment is necessary, slightly tighten or loosen

adjustment screws on bottom of PSS2000. (See Figure 6)

Figure 6

Adjusting Swivel Stops

1. Decide the amount of desired stand swivel (15°, 25° or 35°).

2. Inserta10-24x1/2" screw(not provided)in oneofthethree

swivel stop holes in the stand base. (See Figure 7)

Figure 7

Adjusting Display Roll

1. Loosen upper and lower roll adjustment nuts.(See Figure 8)

2. Level display.

3. TIghten roll adjustment nuts.

Figure 8

Cable Routing and Management

WARNING:

ELECTRICAL SHOCK HAZARD! Improper

routing can lead to wires or cables being damaged. Make

certain display power cable is not routed through areas where

it can be pinched or cut.

1. Routedisplaycablesandwiringthroughcablemanagement

hole in base. (See Figure 9)

NOTE:

Cables may also be routed through a hole in the

mounting surface.

2. Connect wires and cables to display.

Figure 9

Swivel Tension

Adjustment Screws

Swivel Stop Holes

PSS2000 Installation Instructions

USA/International A 8401 Eagle Creek Parkway, Savage, MN 55378

P800.582.6480 / 952.894.6280

F877.894.6918 / 952.894.6918

Europe A Fellenoord 130 5611 ZB EINDHOVEN, The Netherlands

P+31 (0)40 2668620

F+31 (0)40 2668615

Asia Pacific A Room 24F, Block D, Lily YinDu International Building

LuoGang, BuJi Town, Shenzhen, CHINA.

P+86-755-8996 9226

F+86-755-8996 9217

Chief Manufacturing, a division of

Milestone AV Technologies

8800-000070

www.chiefmfg.com

10/08

Table des matières

Autres manuels CHIEF Support et étagère

CHIEF

CHIEF FMSSTRM Manuel utilisateur

CHIEF

CHIEF JHS210 Manuel utilisateur

CHIEF

CHIEF MSB-6134 Manuel utilisateur

CHIEF

CHIEF Small Flat Panel In-Wall Swing Arm Mount FWDIW-I... Manuel utilisateur

CHIEF

CHIEF LW46U P Series Manuel utilisateur

CHIEF

CHIEF FCA3U Manuel utilisateur

CHIEF

CHIEF ER Rack Series Manuel utilisateur

CHIEF

CHIEF MSM Series Manuel utilisateur

CHIEF

CHIEF NAW1K1 Manuel utilisateur

CHIEF

CHIEF PSMH2860 Manuel utilisateur

CHIEF

CHIEF NE1F20 Manuel utilisateur

CHIEF

CHIEF OFB214 Manuel utilisateur

CHIEF

CHIEF FSD-4100 Manuel utilisateur

CHIEF

CHIEF FWDSK110 Manuel utilisateur

CHIEF

CHIEF MIWRF Series Manuel utilisateur

CHIEF

CHIEF CMSI Manuel utilisateur

CHIEF

CHIEF Universal Slat Wall Multi Arm Mount KSY220 Manuel utilisateur

CHIEF

CHIEF FCA2X1U Manuel utilisateur

CHIEF

CHIEF TPA-111 Manuel utilisateur

CHIEF

CHIEF PSM-2540 Manuel utilisateur

CHIEF

CHIEF PAC717 Manuel utilisateur

CHIEF

CHIEF FCAB3X1U Manuel utilisateur

CHIEF

CHIEF SLBU Manuel utilisateur

CHIEF

CHIEF FTR1U Manuel utilisateur

Manuels Support et étagère populaires d'autres marques

Salamander

Salamander Acadia AC/W/L400/WH Manuel utilisateur

Fohhn

Fohhn VAT-09 Guide de l'utilisateur

ricoo

ricoo FS0522 Manuel utilisateur

AMSOIL

AMSOIL BMK-22 Guide rapide

Kargo Master

Kargo Master 48220 Manuel utilisateur

Milestone AV Technologies

Milestone AV Technologies SIMPLICITY SLF2 Manuel utilisateur

ricoo

ricoo S1222 Manuel utilisateur

Ready-Set-Mount

Ready-Set-Mount RSMCM602 Manuel utilisateur

VidaBox

VidaBox VB MNT FFS2 Manuel utilisateur

Welch Allyn

Welch Allyn 48960 Manuel utilisateur

Arkon

Arkon CM035-ST-2 Manuel utilisateur

PROEL

PROEL PLWIN60C Manuel utilisateur

Agilent Technologies

Agilent Technologies E2609B Manuel utilisateur

Mustang

Mustang MV-ARM4 Manuel utilisateur

Mounting Solutions

Mounting Solutions WRM-320 Manuel utilisateur

Pyle

Pyle PMKSPAD1 Manuel utilisateur

ShelterIt

ShelterIt 21208 Manuel utilisateur

SPL

SPL RackPack?4 1040 Manuel utilisateur