CHIEF FWD-111 Manuel utilisateur

ane

Dual Swing Arm Wall Mount

FWD-111

The FWD-111 dual arm wall mount was designed to support

flat panel displays with 10” to 30” diagonal screens and

weighing a maximum of 40 lbs (18.1 kg).

At only 2.15” deep in the closed position, the mount allows

side-to-side pivot adjustment up to 180 degrees in the closed

and the fully extended position. A display can be extended

14.2” from the wall and pivot 360 degrees.

The FWD-111 fits the following VESA® patterns:

• 75mm/75mm (using the Centris™ mount)

• 100mm/100mm (using the Centris mount)

• 200mm/100mm (using the interface bracket with the

Centris mount)

BEFORE YOU BEGIN

•Caution: To prevent damage to the FWD-111, which could affect or void the Factory warranty, and to the

equipment that will be attached to it, thoroughly study all instructions and illustrations before you begin

the installation. Pay particular attention to the “Important Warnings and Cautions” on Page 2.

• The maximum weight to be installed on the FWD-111 wall mount is 40 pounds (18.1 kg).

• The FWD-111 wall mount is designed to be installed using wall studs or supporting framework. The structure to

which the FWD-111 wall mount is anchored must be capable of supporting five times the total weight of the mount

and all attached equipment.

• If you have any questions about this installation, contact Chief Manufacturing at 1-800-582-6480.

INSTALLATION INSTRUCTIONS

CHIEF MANUFACTURING INC.

1-800-582-6480 952-894-6280 FAX 952-894-6918

8401 EAGLE CREEK PARKWAY STE. 700

SAVAGE, MINNESOTA 55378 USA

PART NO. 8832-000132

www.chiefmfg.com

10/05

Installation Instructions FWD-111

IMPORTANT WARNINGS AND CAUTIONS!

WARNING: A WARNING alerts you to the possibility of serious injury or death if you do not follow the instructions.

CAUTION: ACAUTION alerts you to the possibility of damage or destruction of equipment if you do not follow the cor-

responding instructions.

•WARNING: Improper installation can result in serious personal injury! Make sure that the structural members can

support a redundant weight factor five times the total weight of the equipment. If not, reinforce the

structure before installing the FWD-111.

•WARNING: Be aware also of the potential for personal injury or damage to the unit if it is not adequately mounted.

•WARNING: The installer is responsible for verifying that the wall to which the FWD-111 is anchored will safely sup-

port the combined load of all attached components or other equipment.

•WARNING: The weight of the display placed on the FWD-111 must not exceed 40 lbs. (18.1 kg), the maximum load

capacity of the FWD-111.

•WARNING: Watch for pinch points. Do not put your fingers between movable parts.

•WARNING: Make sure the mount and brackets are correctly oriented.

•CAUTION: Check the unit for shipping damage before you begin the installation.

DRAWING

15.93

(EXTENDED)

404.545

12.18

309.314

3.94

100 2.95

2.95

3.94

100

4.69

119.050

2.16

(COLLAPSED)

54.760

Installation Instructions FWD-111

CONTENTS

IMPORTANT WARNINGS AND CAUTIONS ............. 2

DRAWINGS ............................................................... 2

TOOLS REQUIRED FOR INSTALLATION ................ 3

INSPECT THE UNIT BEFORE INSTALLING ............ 3

INTRODUCTION ....................................................... 3

COMPONENTS ......................................................... 4

PARTS ....................................................................... 5

INSTALLATION ......................................................... 6

Secure Wall Bracket .............................................. 6

Tighten Centris Adjustment Screw......................... 6

Install FWD-111 on Wall Bracket........................... 7

Flush Mount – 75mm/100mm Pattern.................... 8

Recessed Mount – 75mm/100mm Pattern ............ 8

200mm/100mm Pattern ......................................... 9

Installing Non-VESA Compliant Mounts ................ 9

CABLE MANAGEMENT ............................................ 10

ADJUSTMENTS ........................................................ 10

Rotational Tilt, Pitch, and Roll Adjustment............. 10

Lateral tension Adjustment .................................... 10

TOOLS REQUIRED FOR

INSTALLATION

• Electric drill and bit set

• Phillips Screwdriver

• Level

NOTE: Other tools may be required depending on the

mounting surface and method of installation.

INSPECT THE UNIT BEFORE

INSTALLING

WARNING: Watch for pinch points. Do not put your fin-

gers between movable parts.

1. Carefully inspect the FWD-111 for shipping damage. If

any damage is apparent, call your carrier claims agent and

do not continue with the installation until the carrier has

reviewed the damage.

NOTE: Read all instructions before starting installation.

2. Lay out components to ensure you have all the required

parts before proceeding (refer to Figure 1 on page 4).

INTRODUCTION

Depending on the size of your display, select one of the follow-

ing FWD-111 installation configurations:

• Install your display using the “Flush Mount – 75mm/

100mm Pattern” on page 8.

• Install your display using the “Recessed Mount – 75mm/

100mm Pattern” on page 8.

• Install your display using the “200mm/100mm Pattern” on

page 9.

• Install your display using the “Installing Non-VESA Com-

pliant Mounts” on page 9.

Installation Instructions FWD-111

COMPONENTS

140

120

100

130

20 110

150

160

50 60

Figure 1. FWD-111 Components

Installation Instructions FWD-111

PARTS

Table 1: Parts

ITEM

NUMBER DESCRIPTION QTY NOTES

10 WALL MOUNT 1

20 PHILLIPS PAN HEAD MACHINE SCREW, M4 x 12mm 4 FLUSH MOUNT

30 PHILLIPS PAN HEAD MACHINE SCREW, M4 x 30mm

(USE WITH 40)* 4

RECESSED

MOUNT

40 3/4” NYLON SPACER 4

50 PHILLIPS PAN HEAD MACHINE SCREW, M4 x 20mm

(USE WITH 60)** 4

60 3/8” NYLON SPACER 4

70 200mm x 100mm INTERFACE BRACKET

(USE WITH 80 AND 90)*** 1200mm x 100mm

Mtg. Hole Pattern80 PHILLIPS FLAT HEAD MACHINE SCREW, M4 x 12mm 6

90 PHILLIPS PAN HEAD MACHINE SCREW, M4 x 5mm 4

100 PHILLIPS PAN WOOD SCREW, #10 x 2-1/2” 2 SINGLE STUD

MOUNTED

110 WASHER 2

120 WALL BRACKET 1

130 COVER PLATE 2 CABLE

MANAGEMENT

140 COVER PLATE FLAT HEAD SCREW 4

150 3/16” HEX KEY 1 For Adjustments

160 5/32” HEX KEY 1 For Set Screw

NOTES:

• *Use M4 x 30mm screws (30) with spacers (40) for recessed applications.

• **Use M4 x 20mm screws (50) with spacers (60) for recessed applications.

• ***Use the six flat head screws (80) to mount the 200mm x 100mm interface bracket (70).

Use four M4 x 5mm screws (90) to mount the Centris bracket to the 200mm x 100mm

interface bracket (70).

Installation Instructions FWD-111

INSTALLATION

Secure Wall Bracket

WARNING: It is the responsibility of the installer to ver-

ify that the surface to which the FWD-111 is

anchored will safely support the combined

load of all attached components and equip-

ment.

Install the FWD-111 as follows:

1. Determine the exact mounting location prior to installa-

tion, considering the unit’s swing and extension radius.

WARNING: Improper installation can result in serious

personal injury! Make sure that the struc-

tural members can support a redundant

weight factor five times the total weight of

the equipment. If not, reinforce the struc-

ture before installing the FWD-111.

2. Using the wall bracket (120) as a template, drill two 3/32”

pilot holes to a minimum depth of 1-1/2”.

3. Using two #10 x 2-1/2” wood screws (100) and two wash-

ers (110), secure the wall bracket (120). See Figure 2.

4. Check mount to insure it is level and adjust to level if nec-

essary.

5. Make sure no power is supplied to the display before

attempting to mount the display.

6. Remove four screws (supplied) from the back of your dis-

play (see Figure 3).

Tighten Centris Adjustment Screw

1. Check adjustment screw on the Centris mount interface to

ensure that the screw is tight. See Figure 4.

2. If needed, use a Phillips screwdriver to tighten the screw.

120

110

100

Figure 2. Secure Wall Bracket

Figure 3. Remove Screws

Figure 4. Tighten Centris Adjustment Screw

Installation Instructions FWD-111

Install FWD-111 on Wall Bracket

1. Install the FWD-111 on the wall bracket by placing the top

of the FWD-111 over the top of the wall bracket and push-

ing the bottom of the FWD-111 over the bottom of the

wall bracket (see Figure 5).

2. Using the 5/32” hex wrench (160), secure the FWD-111 to

the wall bracket by tightening the set screw (see Figure 6).

NOTE: Refer to the “INTRODUCTION” on page 3 to deter-

mine the correct procedure to mount your display

using the applicable VESA mounting-hole pattern

configuration.

Set screw

Figure 5. Install FWD-111 on Wall Bracket

Figure 6. Tighten Setscrew to Secure

Installation Instructions FWD-111

Flush Mount – 75mm/100mm Pattern

To flush mount the display using the 75mm/100mm mounting

hole pattern, do the following:

1. Install two M4 x 12mm screws (20) into the top mounting

holes on the display (see Figure 7 and Figure 8).

2. Align the mounting holes on the Centris mount with the

screws installed on the display. Hang the display on the

mount.

3. Install two remaining M4 x 12mm screws (20) into the

bottom mounting holes on the display.

4. Secure the display to the mount by tightening all four

M4 x 12mm screws (20).

5. Proceed to “CABLE MANAGEMENT” on page 10 and

the “ADJUSTMENTS” on page 10 and perform those two

procedures to complete the installation process.

Recessed Mount – 75mm/100mm Pattern

To recess mount the display using the 75mm x 100mm mount-

ing hole pattern, do the following:

NOTE: Use one of the following screw and spacer combina-

tions: (30 with 40) or (50 with 60).

CAUTION: If your display uses a screw size other than

M4 X 20mm or M4 X 30mm, DO NOT use the

M4 X 20mm or M4 X 30mm screws. Using the

wrong screws could result in damage to your dis-

play.

1. Select four screws (30 or 50) and four spacers (40 or 60),

depending on your display model.

2. Place four spacers (40 or 60) over the mounting holes on

the back of your display (see Figure 7, Figure 8

and Figure 9).

3. Align the mounting holes on the Centris mount with the

spacers installed on the back of your display.

4. Secure the mount to your display using the four screws (30

or 50) that were selected in step 1.

5. Perform the procedure to “Install FWD-111 on Wall

Bracket” on page 7.

6. Proceed to “CABLE MANAGEMENT” on page 10 and

the “ADJUSTMENTS” on page 10 and perform those two

procedures to complete the installation process.

30 or 50

40 or 60

Figure 9. Recessed Mount – 75mm/100mm Pattern

Figure 8. Flush Mount – 75mm/100mm Pattern

75mm/75mm

VESA Pattern

(Inside Mounting Holes) 100mm/100mm

VESA Pattern

(Outside Mounting Holes)

Figure 7. 75mm/100mm VESA Mounting Patterns

Installation Instructions FWD-111

200mm/100mm Pattern

To mount the display using the 200mm x 100mm mounting

hole pattern, do the following:

1. Attach interface bracket (70) to the display using six

M4 x 12mm flat head screws (80). See Figure 10.

2. Start two M4 x 5mm Phillips pan head screws (90) into the

top two mounting holes of the display (see Figure 11).

3. Hang the mount from the two screws started in Step 2.

4. Install the remaining two M4 x 5mm Phillips pan head

screws (90) into the bottom two mounting holes of the dis-

play.

5. Secure the display to the mount by tightening all four

M4 x 5mm Phillips pan head screws (90).

6. Proceed to “CABLE MANAGEMENT” on page 10 and

the “ADJUSTMENTS” on page 10 and perform those two

procedures to complete the installation process.

Installing Non-VESA Compliant Mounts

1. For custom interface brackets, contact:

Chief Manufacturing.

Figure 10. Install 200mm/100mm Pattern

Figure 11. Hang Display onto Mount

Installation Instructions FWD-111

CABLE MANAGEMENT

WARNING:Make sure your cables do not run through a

pinch point.

1. Connect and secure power/audio/video cables, making

sure to leave sufficient slack to allow for movement of the

display.

2. Route power/audio/video cables under each arm, allowing

sufficient slack in cables for extension and avoiding pinch

points

3. Secure cables using cover plates (130) and four screws

(140).

ADJUSTMENTS

CAUTION: Overtightening adjustment will cause

excessive wear.

Rotational Tilt, Pitch, and Roll Adjustment

1. Test the Centris adjustment by tilting, pitching, and rolling

the Centris mount interface (see Figure 12).

2. If necessary, remove display from the mount.

3. Use a Phillips screwdriver to tighten or loosen the Centris

adjustment screw.

4. Check for desired tension.

5. Repeat the procedure until desired tension is obtained.

Lateral Tension Adjustment

1. Using a 3/16” hex wrench (150), slightly tighten or loosen

lateral tension adjustment bolt (see Figure 13).

2. Check for desired tension.

3. Repeat Steps 1 and 2 until desired tension is obtained.

Figure 12. Adjust Centris Adjustment Screw

Lateral Tension Adjustment Bolts

Figure 13. Lateral Tension Adjustment

Table des matières

Autres manuels CHIEF Support et étagère

CHIEF

CHIEF JWDSK210 Manuel utilisateur

CHIEF

CHIEF RMF Manuel utilisateur

CHIEF

CHIEF MAC1005 J Series Manuel utilisateur

CHIEF

CHIEF K2W Series Manuel utilisateur

CHIEF

CHIEF MTM1U Manuel utilisateur

CHIEF

CHIEF MAC722 Manuel utilisateur

CHIEF

CHIEF CMA440 Manuel utilisateur

CHIEF

CHIEF SSB-202 Manuel utilisateur

CHIEF

CHIEF RPA287 Manuel utilisateur

CHIEF

CHIEF PLP Series Manuel utilisateur

CHIEF

CHIEF Single Stud Wall Arm CTA-025 Manuel utilisateur

CHIEF

CHIEF CMSZ006 Manuel utilisateur

CHIEF

CHIEF CMA-395 Manuel utilisateur

CHIEF

CHIEF PSB-2244 Manuel utilisateur

CHIEF

CHIEF PACCC1 Manuel utilisateur

CHIEF

CHIEF FCA810V Manuel utilisateur

CHIEF

CHIEF MSP-KTPHD Series Manuel utilisateur

CHIEF

CHIEF Ceiling Plate CMA-330 Manuel utilisateur

CHIEF

CHIEF Fusion FCA831 Manuel utilisateur

CHIEF

CHIEF PAC516 Manuel utilisateur

CHIEF

CHIEF FCAX08 Manuel utilisateur

CHIEF

CHIEF FCA612 Manuel utilisateur

CHIEF

CHIEF SSB-2100 Manuel utilisateur

CHIEF

CHIEF FTR1U Manuel utilisateur

Manuels Support et étagère populaires d'autres marques

Salamander

Salamander Acadia AC/W/L400/WH Manuel utilisateur

Fohhn

Fohhn VAT-09 Guide de l'utilisateur

ricoo

ricoo FS0522 Manuel utilisateur

AMSOIL

AMSOIL BMK-22 Guide rapide

Kargo Master

Kargo Master 48220 Manuel utilisateur

Milestone AV Technologies

Milestone AV Technologies SIMPLICITY SLF2 Manuel utilisateur

ricoo

ricoo S1222 Manuel utilisateur

Ready-Set-Mount

Ready-Set-Mount RSMCM602 Manuel utilisateur

VidaBox

VidaBox VB MNT FFS2 Manuel utilisateur

Welch Allyn

Welch Allyn 48960 Manuel utilisateur

Arkon

Arkon CM035-ST-2 Manuel utilisateur

PROEL

PROEL PLWIN60C Manuel utilisateur

Agilent Technologies

Agilent Technologies E2609B Manuel utilisateur

Mustang

Mustang MV-ARM4 Manuel utilisateur

Mounting Solutions

Mounting Solutions WRM-320 Manuel utilisateur

Pyle

Pyle PMKSPAD1 Manuel utilisateur

ShelterIt

ShelterIt 21208 Manuel utilisateur

SPL

SPL RackPack?4 1040 Manuel utilisateur