Checkpoint Quantum LightSpeed Appliance QLS250 Manuel d'instructions d'installation
[Classification: Protected]
24 August 2022
RACK MOUNTING FOR
CHECK POINT
APPLIANCES
Check Point Copyright Notice
© 2013-2022 Check Point Software Technologies Ltd.
All rights reserved. This product and related documentation are protected by copyright and distributed under
licensing restricting their use, copying, distribution, and decompilation. No part of this product or related
documentation may be reproduced in any form or by any means without prior written authorization of Check
Point. While every precaution has been taken in the preparation of this book, Check Point assumes no
responsibility for errors or omissions. This publication and features described herein are subject to change
without notice.
RESTRICTED RIGHTS LEGEND:
Use, duplication, or disclosure by the government is subject to restrictions as set forth in subparagraph (c)
(1)(ii) of the Rights in Technical Data and Computer Software clause at DFARS 252.227-7013 and FAR
52.227-19.
TRADEMARKS:
Refer to the Copyright page for a list of our trademarks.
Refer to the Third Party copyright notices for a list of relevant copyrights and third-party licenses.
Important Information
Rack Mounting for Check Point Appliances|3
Important Information
Latest Software
We recommend that you install the most recent software release to stay up-to-date with the
latest functional improvements, stability fixes, security enhancements and protection against
new and evolving attacks.
Certifications
For third party independent certification of Check Point products, see the Check Point
Certifications page.
Latest Version of this Document in English
Open the latest version of this document in a Web browser.
Download the latest version of this document in PDF format.
Feedback
Check Point is engaged in a continuous effort to improve its documentation.
Please help us by sending your comments.
Revision History
Date Description
24 August 2022 Updated for TE250XN appliances
21 February 2022 Rebranding - New Check Point logo
18 January 2022 First release of this document
Table of Contents
Rack Mounting for Check Point Appliances|4
Table of Contents
Introduction
5
QLS250, QLS450, QLS650, and QLS800
6
General Requirements for Racks
6
Telescopic Rails Hardware
6
Installation Overview
7
Attaching the Inner Appliance Rails
7
Attaching the Ear Mounts
9
Attaching the Outer Rack Rails
10
Installing the Appliance in the Rack
12
Removing the Appliance
13
Appliance Air Vents
13
TE250XN
15
General Requirements for Racks
15
Telescopic Rails Hardware
16
Installation Overview
17
Attaching the Inner Appliance Rails
17
Attaching the Ear Mount Brackets
19
Preparing Round-Hole Rack Rails
20
Attaching the Outer Rack Rails
20
Installing the Appliance in the Rack
22
Removing the Appliance
23
Appliance Air Vents
23
Introduction
Rack Mounting for Check Point Appliances|5
Introduction
This guide applies to these Check Point Appliances:
Appliance U In This Document
Quantum LightSpeed Appliance QLS250 2U QLS250
Quantum LightSpeed Appliance QLS450 3U QLS450
Quantum LightSpeed Appliance QLS650 3U QLS650
Quantum LightSpeed Appliance QLS800 3U QLS800
SandBlast Threat Emulation TE250XN 1U TE250XN
QLS250, QLS450, QLS650, and QLS800
Rack Mounting for Check Point Appliances|6
QLS250, QLS450, QLS650, and
QLS800
General Requirements for Racks
Check Point appliances are designed for a standard 19-inch (48.26 cm) rack (see specification EIA-310-D).
The telescopic rails are designed for racks with these specifications:
Minimum Depth Maximum Depth
22 inches (55.9 cm) 32 inches (81.3 cm)
24 inches (61 cm) 36 inches (91.4 cm)
Front and rear rack doors must have equally distributed holes on at least 65% of the surface area to give
sufficient airflow. Make sure that the racks have sufficient clearance to service the Check Point appliances
that are mounted on telescopic rails.
Rack
Side Clearance Requirement
Front 36 in (91.4 cm) plus additional clearance, if necessary, for the mechanical lift used to move
the appliance and rails equipment.
Rear 16 in (40.6 cm) from the rear of the rack or appliance without the rear cabinet door.
22 in (55.9 cm) from the rear of the rack or appliance with the rear cabinet door.
These are the physical specifications of the LightSpeed Appliances:
Security Appliance Width Depth Height U
QLS250 442 mm 610 mm 88 mm 2U
QLS450, QLS650, and QLS800 442 mm 610 mm 132 mm 3U
Telescopic Rails Hardware
Important - To prevent injury or damage, at least two people are required to install the
appliance in a rack.
Rack Mounting Tools
We recommend that you use a Phillips PH2 screwdriver with a magnetic head to hold and retrieve screws.
QLS250, QLS450, QLS650, and QLS800
Rack Mounting for Check Point Appliances|7
Item Hardware Description Qty Use
1 Outer rack rail section of the
telescopic rail unit
2 Moves the appliance into position in the rack
2 Inner appliance rail section of
the telescopic rail unit
2 Attaches to the sides of the appliance
3 Ear mount bracket 2 Attaches the appliance to the rack
4 Rack mounting screws 4 Attaches the ear mounts to the rack, which
prevents movement of the appliance
5 Appliance rail screws 12 Attaches the appliance rails to the appliance
6 Ear mount bracket screws 6 Attaches the ear mounts to the appliance
7 Round hole pins 8 Attaches to the outer rack rails
Note - Needed for round hole racks only
Legend
Installation Overview
Telescopic rails installation consists of these procedures:
nAttaching the inner rails to the appliance
nAttaching the ear mounts to the appliance
nAttaching the outer rack rails to the rack
nInstalling the appliance in the rack
Attaching the Inner Appliance Rails
The outer rack rail section and the inner appliance rail section come as one unit when you open the box.
QLS250, QLS450, QLS650, and QLS800
Rack Mounting for Check Point Appliances|8
Before you can attach each appliance rail to the side of the appliance, you must remove the inner appliance
rails from the outer rack rails.
To remove the inner appliance rail from the telescopic rail unit:
1. Extend the inner appliance rail from the outer rail until the rails locks in place.
2. Press the inner rail release latch, as shown, and pull the inner appliance rail straight out.
3. Do steps 1 and 2 again for the other telescopic rack rail unit.
Item Description
1 Inner rack rail
2 Release latch
3 Outer appliance rail
Legend
To install the inner appliance rails to the appliance:
1. Place the appliance rail on the side of the appliance and make sure:
nThe release latch is facing away from the appliance
nThe arrow on the release latch points to the front of the appliance
nThe appliance rail is longer than the appliance
2. Install the appliance rails to the side of the appliance with the six provided screws. Refer to the below
appliance rail image.
Note - Do not over-tighten the screws. Check Point recommends that you leave
the rail mounting screws loose until the server is completely installed. This eases
installation by preventing binding of the server in the rack.
QLS250, QLS450, QLS650, and QLS800
Rack Mounting for Check Point Appliances|9
3. Do steps 1 and 2 again to install the appliance rail on the other side of the appliance.
Item Description
1 Appliance rail screws
2 Release latch (press this latch to remove the appliance from the rack)
Legend
Attaching the Ear Mounts
Attach the ear mounts to the left and right side of the front of the appliance to allow:
nEasy pulling in and pulling out of the appliance while it is in the rack using the extraction handles
nLocking the appliance into the rack using the rack mounting screws
Item Hardware Description Use
1 Holes for ear bracket screws Attaches ear mount to the appliance
2 Extraction handle Pulls appliance away from the rack
3 Rack post mounting hole for the rack
mounting screw
When the screw is fastened, the appliance cannot be
pulled out of the rack
Legend
QLS250, QLS450, QLS650, and QLS800
Rack Mounting for Check Point Appliances|10
To attach the ear mounts to the appliance:
1. Place the ear mount on the side of the appliance near the front panel.
2. Attach the ear mount to the appliance with three ear bracket screws.
nQLS250:
nQLS450, QLS650, and QLS800:
3. Do steps 1 - 2 again for the other side of the appliance.
Attaching the Outer Rack Rails
Attach the outer rack rails to the rack. Make sure that you have the two rack rails ready.
Autres manuels pour Quantum LightSpeed Appliance QLS250
2
Ce manuel convient aux modèles suivants
4
Table des matières
Autres manuels Checkpoint Pare-feu
Checkpoint
Checkpoint SMB 1500 Series Manuel utilisateur
Checkpoint
Checkpoint 5070 Manuel utilisateur
Checkpoint
Checkpoint M2 Manuel utilisateur
Checkpoint
Checkpoint 1100 Manuel utilisateur
Checkpoint
Checkpoint Power-1 P-10 Manuel utilisateur
Checkpoint
Checkpoint Quantum LightSpeed Appliance QLS250 Mode d’emploi
Checkpoint
Checkpoint Smart-1 series Manuel utilisateur
Checkpoint
Checkpoint 2200 Mode d’emploi
Checkpoint
Checkpoint 4000 Series Manuel utilisateur
Checkpoint
Checkpoint 500W Manuel utilisateur
Checkpoint
Checkpoint InterSpect 210 Manuel utilisateur
Checkpoint
Checkpoint Smart-1 525 Manuel utilisateur
Checkpoint
Checkpoint 600 Manuel utilisateur
Checkpoint
Checkpoint UTM-1 Edge W16 Manuel utilisateur
Checkpoint
Checkpoint Power Sensor 2000 Manuel utilisateur
Checkpoint
Checkpoint QUANTUM LIGHTSPEED Manuel utilisateur
Checkpoint
Checkpoint UTM-1 1050 Manuel utilisateur
Checkpoint
Checkpoint MAESTRO R80.20SP Mode d’emploi
Checkpoint
Checkpoint TE1000X Manuel utilisateur
Checkpoint
Checkpoint 15000 Manuel utilisateur
