CHCNAV NX510 Manuel utilisateur
Make your work more efficient
CHCNAV NX510
Commissioning Guide
Precision Agriculture | November 2020
Preface
CHCNAV NX510 COMMISSIONING MANUAL | 2020-11 P a g e | 2
Table of Contents
Preface ............................................................................................................................3
Copyright ........................................................................................................................... 3
Safety Warnings................................................................................................................. 3
FCC Interference Statement .............................................................................................. 3
CE Interference Statement ................................................................................................ 4
1Preparation before commissioning.............................................................................5
1.1 Software installation.................................................................................................... 5
1.2 Controller upgrade....................................................................................................... 9
1.3 Software Registration ................................................................................................ 11
1.4 Software update ........................................................................................................ 12
2Receiver settings ..................................................................................................... 15
2.1. Meaning of signal icons............................................................................................ 15
2.2 Multi-network mode (using a network base station)................................................ 16
2.4 Single-network mode (using tablet/ controller built-in network) ............................. 19
3Mechanical Calibration............................................................................................ 20
3.1. Install Settings........................................................................................................... 21
3.2 Vehicle parameter input............................................................................................ 22
3.3 Controller Orientation ............................................................................................... 25
3.4 GA-Sensor installation ............................................................................................... 25
3.5 Angle sensor .............................................................................................................. 26
3.6 Steering Wheel Calibration........................................................................................ 27
3.7 Installation error calibration...................................................................................... 32
Preface
CHCNAV NX510 COMMISSIONING MANUAL | 2020-11 P a g e | 3
Preface
Copyright
Copyright 2016-2017
CHC | Shanghai Huace Navigation Technology Ltd. All rights reserved. The CHC are trademark
of Shanghai Huace Navigation Technology Limited. All other trademarks are the property of
their respective owners.
Trademarks
All product and brand names mentioned in this publication are trademarks of their respective
holders.
Safety Warnings
The Global Positioning System (GPS) is operated by the U.S. Government, which is solely
responsible for the accuracy and maintenance of the GPS network. Accuracy can also be
affected by poor satellite geometry and obstructions, like buildings and heavy canopy.
FCC Interference Statement
This equipment has been designed to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules in the Portable Mode. These limits are designed to provide
reasonable protection against harmful interference in a residential installation.
Operation is subject to the following two conditions: (1) this device may not cause harmful
interference and (2) this device must accept any interference received, including interference
that may cause undesired operation.
Preface
CHCNAV NX510 COMMISSIONING MANUAL | 2020-11 P a g e | 4
CE Interference Statement
Declaration of Conformity: Hereby, Shanghai Huace Navigation Technology Ltd. declares that
the NX510 is in compliance with the essential requirements and other relevant provisions of
Directive 2014/53/EU. A copy of the Declaration of conformity can be found at Shanghai Huace
Navigation Technology Ltd.
Preparation before commissioning
CHCNAV NX510 COMMISSIONING MANUAL | 2020-11 P a g e | 5
1 Preparation before commissioning
1.1 Software installation
Before installing the software, check its current version. (Click AgNav3.0 to run the software,
click [Settings]-[About], you can view the software version and firmware version.)
Before starting the commissioning of the NX510 autosteering system, please contact your
CHCNAV representative to check out if newest software or firmware upgrades are available
for your system. If your NX510 is already updated, you can proceed directly to the Section
2 Receiver Setting.
Preparation before commissioning
CHCNAV NX510 COMMISSIONING MANUAL | 2020-11 P a g e | 6
Insert the USB flash drive into the display, click [ ], and [ES file browser]
Find the USB disk path (usually named USB500 *) on the left side of the ES file Explorer and
find the software installation package named [AgNav3. *. Apk]
Preparation before commissioning
CHCNAV NX510 COMMISSIONING MANUAL | 2020-11 P a g e | 7
Double-click the installation package and click [Install]
Preparation before commissioning
CHCNAV NX510 COMMISSIONING MANUAL | 2020-11 P a g e | 8
Wait for the software installation to be completed, and then click [Open] to start the software.
The software installation is complete.
Preparation before commissioning
CHCNAV NX510 COMMISSIONING MANUAL | 2020-11 P a g e | 9
1.2 Controller upgrade
Update Via Wi-Fi
Step 1: Open WI-FI on your laptop and find GNSS-XXXXXXX (XXXXXXX is the SN number of the
controller, which can be seen on the nameplate of the controller), the Wi-Fi password is:
12345678, open the browser and enter the URL: 192.168.1.1,, click [chose] after entering the
interface and select the appropriate firmware (firmware name format:
Update_NX500_vx.x.xx_b20xxxxxxx.bin),
Step 2: Get into the receiver setting webpage and choose [Firmware]-[Firmware Update].Click
[Browse],find out the firmware you saved in your laptop.
Step 3:After choose the right firmware, click[Confirm].The firmware will start to upload.
Preparation before commissioning
CHCNAV NX510 COMMISSIONING MANUAL | 2020-11 P a g e | 10
Step 4: Wi-Fi will automatically disconnect after the upload is successful, and the upload web
page will Off, after 5s the lights on the controller's LED panel flashes in sequence and this
means the controller is upgrading itself .Reconnect after the upgrade is complete to see if the
firmware number has changed.
Table des matières
Autres manuels CHCNAV Système de pilotage automatique
