Chauvet Obey 3 Manuel utilisateur

3000 N 29th Ct, Hollywood, FL 33020 U.S.A.

(800) 762-1084 –(954) 929-1115

FAX (954) 929-5560

www.chauvetlighting.com

User Manual

Snapshot

Use on Dimmer

Outdoor Use

Sound Activated

DMX

Master/Slave

Autoswitching

Power Supply

Replaceable Fuse

User Serviceable

Duty Cycle

TABLE OF CONTENTS

1. BEFORE YOU BEGIN................................................................................................................................................... 3

WHAT IS INCLUDED ................................................................................................................................................................................ 3

UNPACKING INSTRUCTIONS .................................................................................................................................................................... 3

MANUAL CONVENTIONS ......................................................................................................................................................................... 3

ICONS .................................................................................................................................................................................................. 3

SAFETY INSTRUCTIONS .......................................................................................................................................................................... 4

2. INTRODUCTION ........................................................................................................................................................... 5

FEATURES ............................................................................................................................................................................................ 5

PRODUCT OVERVIEW............................................................................................................................................................................. 6

3. SETUP .......................................................................................................................................................................... 7

AC POWER........................................................................................................................................................................................... 7

MOUNTING............................................................................................................................................................................................ 7

Orientation................................................................................................................................................................ 7

Installation ................................................................................................................................................................ 7

4. OPERATING INSTRUCTIONS...................................................................................................................................... 8

OPERATING MODES............................................................................................................................................................................... 8

Preset Operation....................................................................................................................................................... 8

Chases Operation..................................................................................................................................................... 8

Macro Operation....................................................................................................................................................... 8

OPERATING FUNCTIONS......................................................................................................................................................................... 9

Strobe....................................................................................................................................................................... 9

Blackout.................................................................................................................................................................... 9

Manual RGB............................................................................................................................................................. 9

Sound....................................................................................................................................................................... 9

5. APPENDIX.................................................................................................................................................................. 10

DMX PRIMER ..................................................................................................................................................................................... 10

GENERAL MAINTENANCE...................................................................................................................................................................... 10

FIXTURE LINKING................................................................................................................................................................................. 11

Data Cabling........................................................................................................................................................... 11

DMX Data Cable..................................................................................................................................................... 11

Cable Connectors................................................................................................................................................... 11

3-Pin to 5-Pin Conversion Chart.............................................................................................................................. 12

Setting up a DMX Serial Data Link.......................................................................................................................... 12

SETTING THE STARTING ADDRESS ........................................................................................................................................................ 13

GENERAL TROUBLESHOOTING .............................................................................................................................................................. 13

CONTACT US...................................................................................................................................................................................... 13

RETURNS PROCEDURE ........................................................................................................................................................................ 14

CLAIMS .............................................................................................................................................................................................. 14

TECHNICAL SPECIFICATIONS ................................................................................................................................................................ 14

1. Before You Begin 3 11/30/2009 10:32 AM

1. BEFORE YOU BEGIN

What is included

1 x Obey™3

1 x Power supply

1 x Warranty Card

1 x User Manual

Unpacking Instructions

Immediately upon receiving a fixture, carefully unpack the carton, check the contents to ensure that

all parts are present, and have been received in good condition. Notify the shipper immediately and

retain packing material for inspection if any parts appear damaged from shipping or the carton itself

shows signs of mishandling. Save the carton and all packing materials. In the event that a fixture

must be returned to the factory, it is important that the fixture be returned in the original factory box

and packing.

Manual Conventions

CHAUVET manuals use the following conventions to differentiate certain types of information from

the regular text.

CONVENTION

MEANING

[10]

A DIP switch to be configured

<Menu>

A key to be pressed on the fixture’s control panel

1~512

A range of values

50/60

A set of values of which only one can be chosen

Settings

A menu option not to be modified (for example, showing the operating mode/current status)

MENU > Settings

A sequence of menu options to be followed

A value to be entered or selected

Icons This manual uses the following icons to indicate information that requires special attention on the part

of the user.

ICONS

MEANING

This paragraph contains critical installation, configuration or operation information. Failure

to comply with this information may render the fixture partially or completely inoperative,

cause damage to the fixture or cause harm to the user.

This paragraph contains important installation or configuration information. Failure to

comply with this information may prevent the fixture from functioning correctly.

This paragraph reminds you of useful, although not critical, information.

1. Before You Begin 4 11/30/2009 10:32 AM

Safety Instructions

Please keep this User Manual for future consultation. If you sell the unit to another user, be sure that

they also receive this instruction booklet.

Always make sure that you are connecting to the proper voltage, and that the line voltage you are

connecting to is not higher than that stated on the decal or rear panel of the fixture.

This product is intended for indoor use only! To prevent risk of fire or shock, do not expose fixture to

rain or moisture.

Make sure there are no flammable materials close to the unit while operating.

The unit must be installed in a location with adequate ventilation, at least 20 in (50 cm) from adjacent

surfaces. Be sure that no ventilation slots are blocked.

Maximum ambient temperature (Ta) is 104° F (40° C). Do not operate fixture at temperatures higher

than this.

In the event of a serious operating problem, stop using the unit immediately. Never try to repair the

unit by yourself. Repairs carried out by unskilled people can lead to damage or malfunction. Please

contact the nearest authorized technical assistance center.

Never connect the device to a dimmer pack.

Make sure the power cord is never crimped or damaged.

Please read these instructions carefully. It includes important

information about the installation, usage and maintenance of this

product.

2. Introduction 5 11/30/2009 10:32 AM

2. INTRODUCTION

Features

Universal DMX-512 compact controller for 3-channel LED fixtures

Works with all 3-channel LED fixtures

Channel 1: red

Channel 2: green

Channel 3: blue

Playback options include automated, sound-activated or manual RGB

Playback modes:

Preset: 9 built-in colors

Chase: triggers automated programs

Macro: scrolls through the color spectrum

Variable fade times for all playback modes

Variable strobing on the fly

Fader for master dimmer

Adjustable blackout allows fixtures to fade out

Adjustable audio sensitivity

2. Introduction 6 11/30/2009 10:32 AM

Product Overview

Manual RGB

Button

Strobe Button

Preset Button

Sound Button

Fade/Speed/

Strobe/Green

Fader

Chases Button

12 VDC Input

Sound Sensitivity

Adjustment Knob

Blackout

Button

Macro Button

DMX Out

Master

Dimmer/Blue

Fader

Chases/Macro/

Red Fader

Power On/Off

Switch

4. Operating Instructions 7 11/30/2009 10:32 AM

3. SETUP

AC Power This fixture runs on 12 VDC, 500 mA. Before powering on the unit, make sure the power supply

voltage to which you are connecting it is correct.

Always connect the fixture to a switched circuit. Never connect the fixture to a rheostat

(variable resistor) or dimmer circuit, even if the rheostat or dimmer channel is used only as a 0

to 100% switch.

To determine the power requirements for a particular fixture, see the label affixed to the back plate of

the fixture or refer to the fixture’s specifications chart. A fixture’s listed current rating indicates its

average current draw under normal conditions.

Mounting

Orientation

The Obey™3may be mounted in any safe position, provided there is adequate room for

ventilation.

Installation

Please see the drawing below, which shows the back of the controller. It details the

dimensions for mounting. This will aid in placing the holes for installation.

Appendix 8 11/30/2009 10:32 AM

4. OPERATING INSTRUCTIONS

Operating Modes

Preset Operation

This controller has preset color macros. There are nine color macros to choose from, which may be

accessed using the nine preset buttons. Please see the instructions below for this operation.

1. Press <PRESET> until the appropriate LED indicator lights.

2. Adjust the Fade/Speed/Strobe/Green Fader to the desired level to set the Fade Time.

3. Adjust the Master Dimmer/Blue Fader to the desired level.

4. Select one of the nine preset color macros.

5. The Fade time and dimming may now be readjusted.

Please be sure that the Strobe, Blackout, and Manual RGB functions are not overriding the controls.

Sound will not function in Preset Mode.

Chases Operation

This controller has preset color chases, which will change between one color and another. There are

several color combinations to choose from. Please see the instructions below for this operation.

1. Press <CHASES> until the appropriate LED indicator lights.

2. Adjust the Fade/Speed/Strobe/Green Fader to the desired level to set the Fade Time.

3. Adjust the Master Dimmer/Blue Fader to the desired level.

4. Using the Chases/Macro/Red Fader, select one of the color combinations.

5. The Fade time and dimming may now be readjusted.

There are several preset color combinations that may be discovered by moving the

Chases/Macro/Red Fader through the full range of movement.

Please be sure that the Strobe, Blackout, and Manual RGB functions are not overriding the controls.

Sound will function in Preset Mode.

Macro Operation

This controller has preset color macros. This is a static color selection, meaning that no chasing,

movement, or color flows of any kind will occur. There are several color macros to choose from,

which may be accessed using the Chases/Macros Fader. Please see the instructions below for this

operation.

1. Press <MACRO> until the appropriate LED indicator lights.

2. Adjust the Fade/Speed/Strobe/Green Fader to the desired level.

3. Adjust the Master Dimmer/Blue Fader to the desired level.

4. Using the Chases/Macro/Red Fader, select one of the color macros.

5. The Fade time and dimming may now be readjusted.

Please be sure that the Strobe, Blackout, and Manual RGB functions are not overriding the controls.

Sound will not function in Preset Mode.

5. Appendix 9 11/30/2009 10:32 AM

Operating Functions

Strobe

This controller has multiple functions for the 3 faders. One of the functions for the middle fader

(Fade/Speed/Strobe/Green) is the strobe function. Please see the instructions below for this

operation.

1. Press <STROBE> until the appropriate LED indicator lights.

2. Adjust the fader to the desired level.

3. In order to return to the desired mode, press <STROBE> until the appropriate LED indicator is

off.

This function may be activated while operating in any other mode (preset, chases, macro).

In order to deactivate this function, the mode must be entered, and the fader must be set to 0.1M

(fully down). Then, deactivate <STROBE>.

Blackout

This controller has a dedicated blackout button. This button works in conjunction with the

Fade/Speed/Strobe/Green fader. Please see the instructions below for this operation.

1. Adjust the Fade/Speed/Strobe/Green fader to the desired value to determine how quickly the

lights will fade out.

2. Press <BLACKOUT> until the appropriate LED indicator lights.

The blackout function will also work with the Fade/Speed/Strobe/Green fader when disabling the

blackout.

The blackout function will not work when the controller is in manual RGB mode.

Manual RGB

This controller has the ability to manually choose a custom color combination by simply using the

Red, Green, and Blue faders. However, <Manual RGB> must first be pressed. Please see the

instructions below for this operation.

1. Press <Manual RGB> until the appropriate LED indicator lights.

2. Adjust the Red, Green, and Blue Faders to the desired levels.

You may press <Manual RGB> until the appropriate LED indicator is off to disable this mode.

Blackout will not work in Manual RGB function.

Fade/Speed will not work in Manual RGB function.

Sound

This controller has preset chases. These chases are normally triggered using the Speed fader.

However, they can be triggered using the built-in microphone, as well. Please see the instructions

below for this operation.

1. Follow the instructions for working with chases in the appropriate section of this manual.

2. Press <SOUND> until the appropriate LED indicator lights.

3. Adjust the Sensitivity Fader to the desired level (turn clockwise to increase sensitivity).

You may press <SOUND> until the appropriate LED indicator is off to disable this mode.

You may adjust the master dimmer and the fade time in this mode with the appropriate faders.

5. Appendix 10 11/30/2009 10:32 AM

5. APPENDIX

DMX Primer

There are 512 channels in a DMX connection. Channels may be assigned in any manner. A fixture

capable of receiving DMX will require one or a number of sequential channels. The user must assign

a starting address on the fixture that indicates the first channel reserved in the controller. There are

many different types of DMX controllable fixtures and they all may vary in the total number of

channels required. Choosing a start address should be planned in advance. Channels should never

overlap. If they do, this will result in erratic operation of the fixtures whose starting address is set

incorrectly. You can however, control multiple fixtures of the same type using the same starting

address as long as the intended result is that of unison movement or operation. In other words, the

fixtures will be slaved together and all respond exactly the same.

DMX fixtures are designed to receive data through a serial Daisy Chain. A Daisy Chain connection is

where the DATA OUT of one fixture connects to the DATA IN of the next fixture. The order in which

the fixtures are connected is not important and has no effect on how a controller communicates to

each fixture. Use an order that provides for the easiest and most direct cabling. Connect fixtures

using shielded two conductor twisted pair cable with three pin XLR male to female connectors. The

shield connection is pin 1, while pin 2 is Data Negative (S-) and pin 3 is Data positive (S+).

General Maintenance

To maintain optimum performance and minimize wear, fixtures should be cleaned frequently. Usage

and environment are contributing factors in determining frequency. As a general rule, fixtures should

be cleaned at least twice a month. Dust build up reduces light output performance and can cause

overheating. This can lead to reduced lamp life and increased mechanical wear. Be sure to power off

fixture before conducting maintenance.

Unplug fixture from power.

Use a vacuum or air compressor and a soft brush to remove dust collected on external

vents.

Clean all glass when the fixture is cold with a mild solution of glass cleaner or Isopropyl

Alcohol and a soft lint free cotton cloth or lens tissue.

Apply solution to the cloth or tissue and drag dirt and grime to the outside of the lens.

Gently polish optical surfaces until they are free of haze and lint.

The cleaning of external optical lenses and/or mirrors must be carried out periodically to optimize light

output. Cleaning frequency depends on the environment in which the fixture operates. Damp, smoky

or particularly dirty surroundings can cause greater accumulation of dirt on the unit’s optics. Clean

with soft cloth using normal glass cleaning fluid. Clean the external optics at least every 20 days.

Clean the fixture at least every 30/60 days.

Always dry the parts carefully after cleaning them.

Never spin a fan using compressed air.

Table des matières

Autres manuels Chauvet Système de contrôle

Chauvet

Chauvet Stage Designer 50 Manuel utilisateur

Manuels Système de contrôle populaires d'autres marques

Pentair Pool Products

Pentair Pool Products Compool Manuel utilisateur

ComfortNET

ComfortNET CTK04 Manuel utilisateur

Fireye

Fireye InSight II 95DSS3 Manuel utilisateur

CAME

CAME G3000 Manuel utilisateur

Idemia

Idemia MorphoAccess VP MD Manuel utilisateur

Axis

Axis P1445-LE-3 Manuel utilisateur

HEIDENHAIN

HEIDENHAIN TNC 150 B Manuel utilisateur

CNC-Step

CNC-Step High-Z T-Series Manuel utilisateur

Doosan

Doosan DVF Series Manuel utilisateur

Honeywell

Honeywell KAP 140 Manuel utilisateur

Honeywell

Honeywell vk41 series Manuel utilisateur

AirBench

AirBench FPW Guide d'installation

Cypress

Cypress HHR-3160 Manuel utilisateur

CAME

CAME GLT40AOS Manuel utilisateur

Zonex

Zonex GEN II -VVT Guide de l'utilisateur

Altronics

Altronics K 9650 Manuel utilisateur

micro-trak

micro-trak RoadMaster Manuel utilisateur

micro-trak

micro-trak Calc-An-Acre II Manuel utilisateur