Chasing E-Reel Manuel utilisateur
CHASING E-Reel Manual
E-Reel
The E-Reel has 14 specialized stainless steel bearings, which adopts high precision aluminum
alloy synchronous belt to drive and high quality stainless steel reciprocating lead-screw line anti-
blast technology. Up to 200 meters of tether. E-Reel offers 4800mAh large capacity battery, which
is up to 30 retracting cycles. E-Reel also supports manual rocker retracting to discharge line, and
allows single person operation and quick-deployment. Let you get rid of the trouble of manual
winding and enjoy the underwater exploration.
1. Power switch
2. Tether / charging socket
3. Speed knob：stop/slow/fast
4. Power indicator：Green 100%-60%；Yellow 59%-20%；Red 19%-0%；The indicator flashes
when the motor is running
5. Handle interface
6. Handle
7. Lifting handle
8. 3 meters tether：Used for connecting the remote controller and the E-Reel
Specifications
SIZE(mm)
280*150*270
WEIGHT
2.9kg
MAX STORAGE LENGTH
200 meters
BATTERY CAPACITY
4800mAh
NUMBER OF CYCLES
>300 times
RUNTIME
30 times
WIPING SPEED
3 gears
TAKE-UP SPEED（200m）
Fast Speed 200s
Low Speed 9min
OPERATING TEMPERATURE
-10℃~45℃
CHARGING TIME
2H
Note: Charging time varies by environmental factors, actual results will vary
Connection
1. Connect the 3 meters tether to the E-Reel and Remote Controller.
2. Connect the tether of the E-Reel to the ROV tether socket and tighten the nut. Reserve a suitable
length and hang the tether sleeve on the tail safety buckle and tighten it.
Instructions
1. Install
1) Press the button on the right side of the straightener to open the lid
2) Insert the tether plug into the groove interface of the E-Reel and tighten the nut
3) Install the tether into the straightener and close the lid
4) Hold the E-Reel, turn on the switch, rotate the speed switch to slow/fast speed and start
winding
5) Finishing
1 2 3
4 5 6
2. Wind down
1) Press the button on the right side of the straightener to open the lid.
2) Take out the tether from the straightener.
3) Close the lid.
4) Start to wind down the tether by hand.
3. Wind up
1）Press the button on the right side of the straightener to open the lid.
2）Install the tether into the straightener, as shown in the picture.
3）Close the lid of the straightener.
4）Hold the E-Reel, turn on the switch, rotate the speed switch to slow/fast speed and start
winding
5）Finishing
Note: in the case that the winder is out of power, you can use the manual handle for rewinding.
Charging guidance
Adapter（12.6V 3A) : It could charge the Remote Controller and E-Reel.
Red light indicates Charging, green light indicates full charged.
Warning: Unplug the adapter when charging is complete
Precautions
1. You need to wait 4 seconds when you turn on the power for the first time and rotate the speed
knob to slow/fast gear.
2. When there is explosion wire, you should turn off the powerimmediately, finishing after getting
tether organized.
3. When the winding is almost complete, please adjust to a slow speed in advance.After winding
up, please timely adjust to the closing gear and turn off the power.
4. Check if the O-rings on the tether connectors are dropped or damaged. If there are missing or
damaged, please replace them in time.
5. Please pay attention to hold the E-Reel in the process of wire winding up or down.
6. E-Reel supports IP65 class waterproofing. Do not put the E-Reel in the water or splash liquid
on it. E-Reel water damage is out of warranty.
Autres manuels pour E-Reel
1
Table des matières
Autres manuels Chasing Drone
Chasing
Chasing DORY Manuel utilisateur
Chasing
Chasing F1 Manuel utilisateur
Chasing
Chasing GLADIUS mini Manuel utilisateur
Chasing
Chasing M2 S Manuel utilisateur
Chasing
Chasing Gladius Standard Pro Manuel utilisateur
Chasing
Chasing M2 PRO Manuel utilisateur
Chasing
Chasing GLADIUS mini Manuel utilisateur
Chasing
Chasing M2 Manuel utilisateur
Chasing
Chasing GLADIUS mini Manuel utilisateur
Chasing
Chasing M2 PRO Guide d'installation
