Challenger Lifts MR6 Manuel utilisateur

11/19/2020

INSTALLATION,OPERATION AND MAINTENANCE MANUAL

PORTABLE MID-RISE LIFT

Model MR6

6,000 lbs. Capacity

1500 lb Per Arm

2311 South Park Rd Louisville, Kentucky 40219

Email:sales@challengerlifts.com Web site:www.challengerlifts.com

Office 800-648-5438 /502-625-0700 Fax 502-587-1933

IMPORTANT: READ THIS MANUAL COMPLETELY BEFORE

INSTALLING or OPERATING LIFT

Model MR6

Installation, Operation, and Maintenance

File: MR6-IOM-A.doc 2Rev: 11/19/2020

GENERAL SPECIFICATIONS

Maximum Capacity......................................................................................... 6,000 lbs

Minimum Table Height ...............................................................................5 1/2 inches

Maximum Table Height ..................................................................................53 inches

Electrical Requirements .........................................................115V, 50/60 Hz, 1 phase

Lifting Time..................................................................................................45 seconds

Safety Lock ………………………………………………System Mechanical Safety Lock

Fig. 1- General Specifications

Model MR6

Installation, Operation, and Maintenance

File: MR6-IOM-A.doc 3Rev: 11/19/2020

Before You Begin

Safety Notices and Decals

For you safety, and the safety of others,

read and understand all of the safety

notices and decals included here.

Read entire manual before

assembling, installing, operating,

or servicing this equipment.

Proper maintenance and

inspection is necessary for

safe operation.

DO NOT operate a damaged lift.

Safety decals similar to those shown here

are found on a properly installed lift. Be

sure that all safety decals have been

correctly installed on the lift. Verify that all

authorized operators know the location of

these decals and fully understand their

meaning. Replace worn, faded, or

damaged decals promptly.

Do not attempt to raise a

vehicle on the lift until the lift

has been correctly installed

and adjusted as described in

this manual.

WARNING

Model MR6

Installation, Operation, and Maintenance

File: MR6-IOM-A.doc 4Rev: 11/19/2020

Receiving

The shipment should be thoroughly inspected as

soon as it is received. The signed bill of lading is

acknowledgement by the carrier of receipt in good

condition of shipment covered by our invoice.

If any of the goods called for on this bill of lading

are shorted or damaged, do not accept them until

the carrier makes a notation on the freight bill of

the shorted or damaged goods. Do this for your

own protection.

NOTIFY Challenger Lifts AT ONCE if any

hidden loss or damage is discovered after receipt

IT IS DIFFICULT TO COLLECT FOR LOSS OR

DAMAGE AFTER YOU HAVE GIVEN THE

CARRIER A CLEAR RECEIPT.

File your claim with Challenger Lifts promptly.

Support your claim with copies of the bill of lading,

freight bill, and photographs, if available.

Flooring

Be certain you have the proper concrete floor to

properly handle the loaded lift. Floor should be in

generally good condition with no large cracks,

spalling or deterioration. Minimum requirements for

concrete are 4 inches minimum depth, with steel

reinforcement per local commercial practice, 3500

psi, cured for 28 days. Floor should be level within

1/4 inch over the installation area. If these

conditions cannot be met, pads can be poured to

accommodate the lift. Pad must be minimum of 8

ft x 8 ft x 1 ft minimum thickness, 3500 psi steel

reinforced mechanically attached to existing floor.

Failure by purchaser to

provide the recommended

mounting surface could

result in unsatisfactory lift

performance, property

damage, or personal injury.

Vertical Clearance

Check the height of the area where the lift is to be

installed. Clearance should be calculated based on

the full raised height of the lift plus the height of the

tallest vehicle you intend to service.

Failure by purchaser to

provide adequate clearance

could result in unsatisfactory

lift performance, property

damage, or personal injury.

Electrical Requirements

For lift installation and operation, it is necessary to

have a dedicated 115V single-phase 60-cycle

circuit with a 20 amp circuit breaker or time delay

fuse.

Tools Required for Installation

1. Wrenches: 7/16, 1/2, 9/16, 5/8, 11/16, 15/16, 1

1/8 inch

2. Ratchet drive with the following sockets: 7/16,

1/2, 9/16, 1 1/8 inch

3. Funnel

4. Adjustable wrenches: 8 and 12 inch

WARNING

Model MR6

Installation, Operation, and Maintenance

File: MR6-IOM-A.doc 5Rev: 11/19/2020

INSTALLATION

SAFETY REQUIREMENTS FOR INSTALLATION AND

SERVICE

Refer to ANSI/ALI ALIS (current edition)

IMPORTANT:Always wear safety glasses while installing lift.

1. Locate the lift on a level concrete floor with

adequate space on all sides. Minimum floor

thickness is 4”. Minimum floor strength is

3500 psi.

WARNING DO NOT install on asphalt or other

similar unstable surface.

CAUTION If lift is to be used in a paint booth, the

electrical power unit MUST be mounted outside the

booth.

POWER UNIT

1. Connect the end of the hydraulic hose with the

90-degree elbow to the pressure port on the

power unit. Tighten securely to prevent

leaking.

NOTE: To avoid damage to the hose, never

run the hose under the lift or in the path of the

automobile tires.

2. Fill the reservoir with 6 quarts clean 10wt anti-

foam, anti-rust hydraulic oil or Dexron III ATF.

DO NOT USE OILS WITH DETERGENTS.

3. Place the open end of the hose into a clean

bucket.

4. Plug power unit cord into a dedicated 115V

single phase 60 cycle circuit with a 25 amp

circuit breaker or time delay fuse

5. Cycle the power unit (2 seconds on, 2 seconds

off) until the hose expels a steady stream of

fluid.

6. Connect the hose to the tee fitting on the lift.

7. Actuate the power unit and raise the lift fully,

then lower the lift to the floor. Repeat 3 to 4

times.

CAUTION The power unit operates at high

pressure.

Raise and lower lift a few times and check hose

and fittings for leaks and tighten if required.

Check for binding, misalignment or damage.

Correct any unusual condition before raising

vehicle.

LOCK RELEASE CABLE

8. Raise the lift until a click is heard; make sure

the lock pawl can pivot freely.

9. Look for the threaded tab on the safety lock

assembly. Back the jam nut off the threaded

coiler and adjust until the slack is removed.

Tighten the lock nut and test the lock release

mechanism 3 or 4 times to ensure proper

function.

DECAL PLACEMENT

10. Center and apply the Driver Side Center of

Gravity decal (10200L) as shown below. The

arrow on the decal should be pointing in the

direction of the cylinders. Repeat on the

opposite side of the lift with the Passenger

Side Center of Gravity decal (10200R). Place

lift brand decal towards front of the lift as

shown below.

Fig. 2 – Decal Placement

Model MR6

Installation, Operation, and Maintenance

File: MR6-IOM-A.doc 6Rev: 11/19/2020

Owner/Operator Checklist

SAVE THESE INSTRUCTIONS deliver them to

owner/user/employee along with other materials

furnished with this lift.

Demonstrate the operation of the lift to the

owner/operator and review correct and safe lifting

procedures using the Lifting It Right booklet as a

guide.

Safety Notices and Decals

This product is furnished with graphic safety

warning labels, which are reproduced on page 3 of

these instructions. Do not remove or deface these

warning labels, or allow them to be removed or

defaced. For your safety, and the safety of others,

read and understand all of the safety notices and

decals included.

Owner/Employer

Responsibilities

This lift has been designed and constructed

according to ANSI/ALI ALCTV standard. The

standard applies to lift manufactures, as well as to

owners and employers. The owner/employer’s

responsibilities as prescribed by ANSI/ALI ALOIM,

are summarized below. For exact wording refer to

the actual standard provided with this manual in

the literature pack.

The Owner/Employer shall insure that the lift

operators are qualified and that they are trained in

the safe use and operation of the lift using the

manufacturer’s operating instructions; ALI/SM 93-

1, ALI Lifting It Right Safety Manual; ALI/ST-90 ALI

Safety Tips Card; ANSI/ALI ALOIM; American

National Standard for Automotive Lifts-Safety

Requirements for Operation, Inspection and

Maintenance; ALI/WL Series, ALI Uniform Warning

Label Decals/Placards; and in case of frame

engaging lifts, ALI/LP-GUIDE, Vehicle Lifting

Points/Quick Reference Guide for Frame Engaging

Lifts.

The Owner/Employer shall establish procedures

to periodically inspect the lift in accordance with

the lift manufacturer’s instructions or ANSI/ALOIM,

American National Standard for Automotive Lifts-

Safety Requirements for Operation, Inspection and

Maintenance; and the employer shall insure that

the lift inspectors are qualified and they are

adequately trained in the inspection of the lift.

The Owner/Employer shall establish procedures

to periodically maintain the lift in accordance with

the lift manufacturer’s instructions or ANSI/ALOIM,

American National Standard for Automotive Lifts-

Safety Requirements for Operation, Inspection and

Maintenance; and the employer shall insure that

the lift maintenance personnel are qualified and

they are adequately trained in the inspection of the

lift.

The Owner/Employer shall maintain the periodic

inspection and maintenance records

recommended by the lift manufacturer or

ANSI/ALOIM, American National Standard for

Automotive Lifts-Safety Requirements for

Operation, Inspection and Maintenance.

The Owner/Employer shall display the lift

manufacturer’s operating instructions; ALI/SM 93-

1, ALI Lifting It Right Safety Manual; ALI/ST-90 ALI

Safety Tips Card; ANSI/ALI ALOIM; American

National Standard for Automotive Lifts-Safety

Requirements for Operation, Inspection and

Maintenance; and in case of frame engaging lift,

ALI/LP-GUIDE, Vehicle Lifting Points/Quick

Reference Guide for Frame Engaging Lifts; in a

conspicuous location in the lift area convenient to

the operator.

IMPORTANT SAFETY

INSTRUCTIONS

When using your garage equipment, basic safety

precautions should always be followed, including

the following:

1. Read all instructions.

2. Care must be taken as burns can occur from

touching hot parts.

3. To reduce the risk of fire, do not operate

equipment in the vicinity of open containers of

flammable liquids (gasoline).

4. Keep hair, loose clothing, fingers, and all parts

of body away from moving parts.

5. Use only as described in this manual. Use

only manufacturer’s recommended

attachments.

6. ALWAYS WEAR SAFETY GLASSES.

Everyday eyeglasses only have impact

resistant lenses, they are not safety glasses.

SAVE THESE INSTRUCTIONS

Model MR6

Installation, Operation, and Maintenance

File: MR6-IOM-A.doc 7Rev: 11/19/2020

Operating Instructions

NOTE:

After reviewing these instructions and all decals,

get familiar with lift controls by running the lift

through a few cycles before loading vehicle on lift.

Loading Vehicle

1. Be sure lift is fully lowered and service bay is

clear of all personnel before the vehicle is

driven on to lift.

2. The center of gravity of the vehicle should be

located directly over the marked location

shown on the decal in Fig. 2 in the fore and aft

direction. The vehicle must also be centered

side to side. See Fig. 1 on page 2 for proper

orientation of vehicle on the lift.

WARNING Never orient vehicle backwards

on the lift. Improper loading of the lift may

result in personal injury and/or property

damage.

WARNING Lift is designed to raise complete

vehicle. NEVER use to raise just one end or

Side of vehicle.

NOTE:

Some vehicles may have the manufacturer’s

recommended lift points identified by triangle

shape marks located on its undercarriage. Also,

there may be a label located on the right front door

lock face showing specific vehicle lift points. If the

vehicles lift points are not identified, refer to the

service garage lift points shown in Fig. 3.

ALWAYS follow the operating instructions supplied

with the lift.

Ladder

Unitized

Perimeter

Stub

Fig. 3 - Service Garage Lift Points

Model MR6

Installation, Operation, and Maintenance

File: MR6-IOM-A.doc 8Rev: 11/19/2020

CAUTION Most specialty or modified vehicles

cannot be raised on a frame engaging or pad

lift. Contact vehicle manufacturer for raising

or jacking details.

3. Before lifting the vehicle be sure that:

A. Individual axle weight of vehicle does not

exceed one-half lift capacity. See safety

instructions (capacity).

B. Vehicle is stable on lift and neither front

nor rear heavy.

CAUTION With some vehicles, the removal

(or installation) of heavy components may

cause a critical shift in balance and result in

vehicle instability. Refer to the vehicle

manufacturer’s service manual for

recommended procedures when performing

these services.

Raising Vehicle

4. To raise lift:

A. Actuate RAISE switch on electric power unit.

B. Raise vehicle until tires clear floor.

C. Check to make sure all four contact pads

are secure on the vehicle.

D. Continue to raise to desired height ONLY if

vehicle is secure on lift.

E. Once you have reached the required height

set into lock by depressing the lowering

handle.

Lowering Vehicle

5. To lower lift:

Stand clear of lift and vehicle when lowering.

Observe pinch point warning decals.

A. Remove all tools or other objects from lift area.

B. Raise vehicle approximately 1” to

disengage lock.

C. Push LOWERING valve handle to lower lift.

CAUTION Lowering handle must be held

down to continue to lower lift. DO NOT

override self-closing lift controls.

6. Before moving vehicle, be sure lift is at the fully

lowered position and is clear of any tools or

objects.

NOTE:

The lock bar will reset automatically when the lift is

fully lowered or raised a minimum of 1”. If during

the lowering process the lift is stopped before it

gets to the fully lowered position. Reset by

repeating steps 5 or 6 from above.

Model MR6

Installation, Operation, and Maintenance

File: MR6-IOM-A.doc 9Rev: 11/19/2020

MAINTENANCE

NOTE:

To avoid personal injury, permit only qualified personnel to perform maintenance on this lift.

See repair parts breakdown for replacement parts.

ALWAYS: Keep all bolts tight. Check periodically.

ALWAYS: Keep lift clean. Raise lift when cleaning floor area.

DAILY: Check lock bar handle and release mechanism for damage or binding.

WEEKLY: Inspect all lift parts for signs of damage due to improper use.

MONTHLY: Lubricate lock bar pivot bolt and lock bar handle pivot points.

MONTHLY: Lubricate all hinge joints if there are signs of rusting.

SEMI-ANNUALLY: Check fluid level of lift power unit and refill if required. Use only Dexron III ATF or 10wt

anti-foam, anti-rust hydraulic oil. If fluid is required, inspect hose and connections and cylinder seals. Repair

as required.

Model MR6

Installation, Operation, and Maintenance

File: MR6-IOM-A.doc 10 Rev: 11/19/2020

PARTS BREAKDOWN

No Part # Qty Description No Part # Qty Description

1 GTYJ3-01-00 1 Scissor Outside 13

TYJ3-13 2 Scissor Pin

GTYJ3-03-00

1 Scissor Inside 14

TYJ3-08

1 Safety Locking Pin

(Bottom)

3 GTYJ3-02-00 1 Platform 15

TYJ3-10 1 Safety Locking Pin (Top)

4L GTYJ3-04-00L 1 Cylinder Assy. (Left) 16 SR-0114 1 Locking Nut, M18

4R GTYJ3-04-00R 1 Cylinder Assy. (Right) 17 TYJ3-09 2 Cylinder Pin

5 GTYJ3-07-00CH 1 Safety Locking Assy. 18 TYJ3-15 2 Wheel Pin (Small)

6 TYJ3-05-03CH 4 Plate 19

TYJ3-14-00 2 Wheel (Small)

7 MR6-002 4 Hex Bolt, M10x20 20 X10-020 6 Retaining Ring 20mm

8 TYJ3-05-02 4 3” Extension Base 21 MR6-003 6 Retaining Ring 18mm

9 TYJ3-05-01 4 Foot Pad 22

MR6-004 4 Retaining Ring 24mm

10 TYJ3-11-00 2 Wheel (Big) 23

B40129 4 Hex Nut, M20

11 TYJ3-12 2 Wheel Pin (Big) 24 TYJ3-17 4 Washer, M20

12 TYJ3-16 2 Connecting Pin 25

TYJ3-05-02G 4 6 7/8” Extension Base

Table des matières

Autres manuels Challenger Lifts Système de levage

Challenger Lifts

Challenger Lifts EnviroLift EV1020 Manuel d'instructions

Challenger Lifts

Challenger Lifts CL10 Manuel d'instructions

Challenger Lifts

Challenger Lifts E12 Manuel d'instructions

Challenger Lifts

Challenger Lifts EnviroLift EV1020 Manuel d'instructions

Challenger Lifts

Challenger Lifts SA10 Manuel utilisateur

Challenger Lifts

Challenger Lifts SRM10 Manuel d'instructions

Challenger Lifts

Challenger Lifts CL12A Manuel d'instructions

Challenger Lifts

Challenger Lifts Versymmetric Manuel d'instructions

Challenger Lifts

Challenger Lifts CL4P7 Manuel d'instructions

Challenger Lifts

Challenger Lifts CL10 Manuel d'instructions

Challenger Lifts

Challenger Lifts 44040 Manuel d'instructions

Challenger Lifts

Challenger Lifts 44018 Manuel d'instructions

Challenger Lifts

Challenger Lifts 15000-SPRINTER 15000-3S Manuel d'instructions

Challenger Lifts

Challenger Lifts 44060 Manuel d'instructions

Challenger Lifts

Challenger Lifts 68000 Manuel d'instructions

Challenger Lifts

Challenger Lifts BT3300 Manuel d'instructions

Challenger Lifts

Challenger Lifts Versymmetric CL9 Manuel d'instructions

Challenger Lifts

Challenger Lifts EW1020-QC Manuel d'instructions

Challenger Lifts

Challenger Lifts LE12 Manuel d'instructions

Challenger Lifts

Challenger Lifts 15000 Manuel d'instructions

Challenger Lifts

Challenger Lifts E15 Manuel d'instructions

Challenger Lifts

Challenger Lifts 12000 Mode d’emploi

Challenger Lifts

Challenger Lifts CLHM-FLA Manuel utilisateur

Challenger Lifts

Challenger Lifts Versymmetric CL10V3-DPC Manuel d'instructions

Manuels Système de levage populaires d'autres marques

morse

morse 82H-124 Manuel utilisateur

Braun

Braun NL955 Series Manuel utilisateur

haacon

haacon 1889.10 Manuel utilisateur

Protekt

Protekt AT 252 Manuel utilisateur

R. Beck Maschinenbau

R. Beck Maschinenbau HS 600 Manuel utilisateur

Nova Technology International, LLC

Nova Technology International, LLC NAS Series Manuel utilisateur

Genie

Genie Z-60/34 Manuel utilisateur

Screen Technics

Screen Technics INTERFIT Vertical Up Lift Manuel utilisateur

Mortuary Lift

Mortuary Lift ULTIMATE 1000 Manuel utilisateur

Custom Equipment

Custom Equipment Hy-Brid 3 Series Manuel de programmation

Custom Equipment

Custom Equipment Hy-Brid Lifts 2 Series Manuel de programmation

Hy-Brid Lifts

Hy-Brid Lifts HB-P3.6 Manuel de programmation

BERG

BERG BeNomic EasyLeaf Manuel utilisateur

Powermate

Powermate LiftGate LG-3 Manuel utilisateur

Snorkel

Snorkel TM12 Series Manuel utilisateur

Terberg

Terberg OMNIDEKA Manuel utilisateur

Harmar Mobility

Harmar Mobility AL625 Mode d'emploi

Rotary

Rotary SPO16 Manuel utilisateur