Centrodyne S700 Manuel utilisateur
S700 Bluetooth QS
!!!!!!!!!!!!!! !
Revision!D1.0!–!03P!
!
!
!
!
!
Page!1!of!7!
!
!
!
!
!
!
!
!
!
!
S700 Taximeter Internal Bluetooth Quick
Start
!
!
!
!
!
!
!
!
August 28, 2014
!
!
!
!
!
!
!
!
!
!
Centrodyne Inc., All rights reserved.
The information in this document is the property of Centrodyne Inc.
Reproduction or transcription by any means, in whole or in part,
without the prior written consent of Centrodyne Inc., is prohibited.
!
!
S700 Bluetooth QS
!!!!!!!!!!!!!! !
Revision!D1.0!–!03P!
!
!
!
!
!
Page!2!of!7!
!
!
1!GENERAL!INFORMATION!................................................................................................!3!
2!THE!BLUETOOTH!MENU!.................................................................................................!3!
2.1!Status!...........................................................................................................................................!3!
2.2!Pairing!..........................................................................................................................................!4!
2.3!COM!Channel!..............................................................................................................................!5!
3!APPENDIX!–!WINDOWS!7!...............................................................................................!5!
4!CONTACT!INFORMATION!...............................................................................................!7!
!
! !
S700 Bluetooth QS
!!!!!!!!!!!!!! !
Revision!D1.0!–!03P!
!
!
!
!
!
Page!3!of!7!
!
1 GENERAL INFORMATION
The S700 taximeter may contain an internal Bluetooth 2.1 + EDR module.
This module only supports a SPP profile used to establish a serial
communication channel with the meter. If you are not sure whether or not
your device supports the SPP profile, please, contact the manufacturer of
that device.
The COM channel used for Bluetooth communications is the same one
that is available via the plug on the adapter bracket. In order to facilitate
meter programming, configuration, and other tasks the meter
automatically routes communications as follows:
- By default all communications will be via the wired plug on the adapter bracket
unless all of the following conditions apply:
oA BTM is installed in the meter.
oThe meter has been configured to enable Bluetooth communications
oA device has been paired with the BTM and has established an active SPP
connection.
- If all of the above conditions apply then the meter automatically routes
communications through the BTM.
2 THE BLUETOOTH MENU
! !
In an S700 with internal Bluetooth installed you may access menu 9 in
order to control certain Bluetooth functions. (For a description of the menu
system and how it works on the S700 please refer to the S700 User
Guide). To access menu 9 perform the following steps.
a. Make sure that the meter is in VACANT.
b. Push button 4
c. Push 3 two times, the rate display will be blinking with a “9”
d. Push button 6 to enter the Bluetooth menu.
The Bluetooth menu has 3 available items. They are described below:
2.1 Status
BT menu item 1 is the Bluetooth status. This item indicates the current
status of the S700 internal Bluetooth module (BTM) by displaying the
states of the following items in the FARE window:
•BTM!presence!(“b1”!=!installed;!“b0”!=!not!installed)!
•BTM!powered!(“P1”!=!powered;!“P0”!=!not!powered)!
•BTM!connected!to!another!device!(“C1”!=!connected;!“C0”!=!not!
connected)!
S700 Bluetooth QS
!!!!!!!!!!!!!! !
Revision!D1.0!–!03P!
!
!
!
!
!
Page!4!of!7!
!
!
!
!
!
!
!
!
2.2 Pairing
Item 2 of the BT menu is for pairing. The pairing of the BTM with another device
is accomplished by entering the pairing item of the BT Menu. In order to pair a
device with the meter the procedure is as follows:
1. The!meter!must!be!in!VACANT!and!not!connected!to!any!other!BT!device!in!order!to!begin!
the!pairing!process.!
!
2. Go!to!the!BT!menu.!Go!to!item!2.!Once!in!item!2,!the!letter!‘P’!is!displayed!in!the!FARE!
window.!
!
!
!
!
!
!
!
!
!
!
!
3. Press!button!6!to!enter!the!pairing!mode;!“000000”!appears!in!the!FARE!window.!
!
!
!
!
!
4. Initiate!the!pairing!on!the!other!device!(tablet,!pc,!etc.).!This!device!will!send!the!meter!a!6Y
digit!passkey.!
5. The!6Ydigit!passkey!will!be!displayed!in!the!FARE!window.!To!accept!pairing!the!user!pushes!
button!6!on!the!meter;!“done”!appears!in!the!FARE!window.!
S700 Bluetooth QS
!!!!!!!!!!!!!! !
Revision!D1.0!–!03P!
!
!
!
!
!
Page!5!of!7!
!
!
!
!
!
!
!
!
!
!
!
!
6. Meter!sends!appropriate!response!to!the!other!device!and!exits!item!2.!
!
Note that the above description does not include any steps necessary on the
other BT device in order to accomplish the pairing. Depending on the OS of the
other device the sequence and timing of the steps above may be important in
order to accomplish the pairing. (See the Appendix for pairing in Windows 7)
2.3 COM Channel
!
Item 3 of the BT menu displays the current COM channel configuration. An “SP”
indicates that the meter is communicating via the wired plug on the adapter
bracket, while a “BL” indicates that the meter is communicating via the BTM.
This item also allows the user to force the connection to the wired connector on
the adapter bracket. This is useful when the user wants to temporarily connect
the meter to a wired device while not severing the BT connection. To make a
change, press button 6. Each time button 6 is pressed the displayed item is
toggled between “SP” and “BL”. If the password option is enabled on the meter
the correct password must be entered prior to toggling the connection.
!
3 APPENDIX – WINDOWS 7
!
Due to some quirks in the Windows 7 Bluetooth implementation there may be
some difficulty pairing with the meter. We have found the following sequence to
be successful in pairing with a Windows 7 PC.
a. In Windows select Bluetooth from the system tray.
b. In the Bluetooth Devices window select “Add a Device”
c. In the popup window find the device “Centrodyne-000000” where
the last five digits are the serial number of the meter. On the meter
go to the BT menu and enter item 2 so that the fare display shows
“000000”. Now select the device in Windows and press Next.
d. The pairing code should display on the meter and in Windows. First
S700 Bluetooth QS
!!!!!!!!!!!!!! !
Revision!D1.0!–!03P!
!
!
!
!
!
Page!6!of!7!
!
press Next in Windows and then after a brief pause press button 6
on the meter. The pairing should complete successfully.
!
!
S700 Bluetooth QS
!!!!!!!!!!!!!! !
Revision!D1.0!–!03P!
!
!
!
!
!
Page!7!of!7!
!
4 CONTACT INFORMATION
!
!
In Canada and Elsewhere:!
Centrodyne Inc.
3485 Thimens Blvd.
Montreal, Quebec
Canada H4R 1V5
Tel: (514) 331-8760
Fax: (514) 339-1078
In the USA:!
Centrodyne Corp. Of America
34 Park Street Unit #6
Essex Junction, VT 05452
U.S.A
Tel: (802) 857-5479
Fax: (802) 857-5480
!
Autres manuels pour S700
2
Table des matières
Autres manuels Centrodyne Instrument de mesure
Manuels Instrument de mesure populaires d'autres marques
Endress+Hauser
Endress+Hauser Proline Promag 50 Caractéristiques techniques
Siemens
Siemens SITRANS F Coriolis FCT030 Manuel de la liste des pièces
KLINGER
KLINGER CMF V Series Manuel utilisateur
EXFO
EXFO FTB-2 Manuel d'exploitation et d'entretien
Keysight
Keysight M8290A Manuel utilisateur
ADTEK
ADTEK MW-5 Manuel utilisateur