Central Machinery 90589 Manuel utilisateur

TIRE CHANGER

SEMI-AUTOMATIC WITH SWINGING ARM

Model

90589

ASSEMBLY AND OPERATING INSTRUCTIONS

Diagrams within this manual may not be drawn proportionally.

Due to continuing improvements, actual product may differ slightly from the product described herein.

Distributed exclusively by Harbor Freight Tools®.

3491 Mission Oaks Blvd., Camarillo, CA 93011

Visit our website at: http://www.harborfreight.com

Read this material before using this product.

Failure to do so can result in serious injury.

SAVE THIS MANUAL.

manual or any artwork contained herein may be reproduced in any shape or form

without the express written consent of Harbor Freight Tools.

For technical questions or replacement parts, please call 1-800-444-3353.

Manual revised 07g

Page 2SKU 90589 For technical questions, please call 1-800-444-3353.

PRODUCT SPECIFICATIONS

Electrical Requirements 220 V / 60 Hz / 10 A

Motor 1 HP / 1740 RPM

Maximum Tire Diameter 39”

Maximum Tire Width 13”

External Locking Rim Dimensions 10”-18”

Internal Locking Rim Dimensions 12”-20”

Maximum PSI Working Pressure 110 PSI

Bead Break Force 5,500 lb.

Maximum Rotation Torque (Turntable) 795 ft-lb

Air Inlet Fitting Size 1/4”-18 NPT

Weight 566 lb

SAVE THIS MANUAL

You will need this manual for the safety warnings and precautions, assembly,

operating, inspection, maintenance and cleaning procedures, parts list and assembly

diagram. Keep your invoice with this manual. Write the invoice number on the inside

of the front cover. Keep this manual and invoice in a safe and dry place for future

reference.

GENERAL SAFETY RULES

WARNING! Read all instructions

Failure to follow all instructions listed below may result in electric shock,

re, and/or serious injury. The term “power tool” in all of the warnings listed

below refers to your mains-operated (corded) power tool or battery-operated

(cordless) power tool.

SAVE THESE INSTRUCTIONS

WORK AREA

Keep your work area clean and well lit.1. Cluttered benches and dark areas

invite accidents.

Do not operate power tools in explosive atmospheres, such as in the2.

presence of ammable liquids, gases, or dust. Power tools create sparks

which may ignite the dust or fumes.

Keep bystanders, children, and visitors away while operating a power tool.3.

Distractions can cause you to lose control. Protect others in the work area from

debris such as chips and sparks. Provide barriers or shields as needed.

Page 3SKU 90589 For technical questions, please call 1-800-444-3353.

ELECTRICAL SAFETY

Grounded tools must be plugged into an outlet properly installed and1.

grounded in accordance with all codes and ordinances. Never remove the

grounding prong or modify the plug in any way. Do not use any adapter

plugs. Check with a qualied electrician if you are in doubt as to whether

the outlet is properly grounded. If the tools should electrically malfunction or

break down, grounding provides a low resistance path to carry electricity away

from the user.

Double insulated tools are equipped with a polarized plug (one blade is2.

wider than the other). This plug will t in a polarized outlet only one way.

If the plug does not t fully in the outlet, reverse the plug. If it still does

not t, contact a qualied electrician to install a polarized outlet. Do not

change the plug in any way. Double insulation eliminates the need for the

three wire grounded power cord and grounded power supply system.

Avoid body contact with grounded surfaces such as pipes, radiators,3.

ranges, and refrigerators. There is an increased risk of electric shock if your

body is grounded.

Do not expose power tools to rain or wet conditions.4. Water entering a power

tool will increase the risk of electric shock.

Do not abuse the Power Cord.5. Never use the Power Cord to carry the

tools or pull the Plug from an outlet. Keep the Power Cord away from

heat, oil, sharp edges, or moving parts. Replace damaged Power Cords

immediately. Damaged Power Cords increase the risk of electric shock.

PERSONAL SAFETY

Stay alert. Watch what you are doing, and use common sense when1.

operating a power tool. Do not use a power tool while tired or under the

inuence of drugs, alcohol, or medication. A moment of inattention while

operating power tools may result in serious personal injury.

Dress properly. Do not wear loose clothing or jewelry. Contain long2.

hair. Keep your hair, clothing, and gloves away from moving parts. Loose

clothes, jewelry, or long hair can be caught in moving parts.

Avoid accidental starting.3. Be sure the Power Switch is off before plugging

in. Plugging in power tools with the Power Switch on, invites accidents.

Remove adjusting keys or wrenches before turning the power tool on.4. A

wrench or a key that is left attached to a rotating part of the power tool may result

in personal injury.

Page 4SKU 90589 For technical questions, please call 1-800-444-3353.

Do not overreach. Keep proper footing and balance at all times.5. Proper

footing and balance enables better control of the power tool in unexpected

situations.

Use safety equipment. Always wear eye protection.6. Dust mask, non-skid

safety shoes, hard hat, or hearing protection must be used for appropriate

conditions.

TOOL USE AND CARE

Do not force the tool. Use the correct tool for your application.1. The correct

tool will do the job better and safer at the rate for which it is designed.

Do not use the power tool if the Power Switch does not turn it on or off.2.

Any tool that cannot be controlled with the Power Switch is dangerous and must

be replaced.

Disconnect the Power Cord Plug from the power source before making any3.

adjustments, changing accessories, or storing the tool. Such preventive

safety measures reduce the risk of starting the tool accidentally.

Store idle tools out of reach of children and other untrained persons.4. Tools

are dangerous in the hands of untrained users.

Maintain tools with care. Keep cutting tools sharp and clean.5. Properly

maintained tools with a sharp cutting edge are less likely to bind and are easier

to control. Do not use a damaged tool. Tag damaged tools “Do not use” until

repaired.

Check for misalignment or binding of moving parts, breakage of parts,6.

and any other condition that may affect the tool’s operation. If damaged,

have the tool serviced before using. Many accidents are caused by poorly

maintained tools.

Use only accessories that are recommended by the manufacturer for your7.

model. Accessories that may be suitable for one tool may become hazardous

when used on another tool.

SERVICE

Tool service must be performed only by qualied repair personnel. 1. Service

or maintenance performed by unqualied personnel could result in a risk of injury.

When servicing a tool, use only identical replacement parts. Follow2.

instructions in the “Inspection, Maintenance, And Cleaning” section of this

manual. Use of unauthorized parts or failure to follow maintenance instructions

may create a risk of electric shock or injury.

REV 07g

Page 5SKU 90589 For technical questions, please call 1-800-444-3353.

SPECIFIC SAFETY RULES

Maintain a safe working environment.1. Keep the work area well lit. Make

sure there is adequate surrounding workspace. Always keep the work area free

of obstructions, grease, oil, trash, and other debris. Do not use this product in

areas near ammable chemicals, dusts, and vapors.

Maintain labels and nameplates on the Tire Changer.2. These carry important

information. If unreadable or missing, contact Harbor Freight Tools for a

replacement.

Use eye and hearing protection.3. Always wear ANSI approved safety impact

eye goggles and hearing protectors when using this product.

Do not allow children to use or play with this product.4.

Store idle equipment.5. When not in use, tools and equipment should be stored

in a dry location to inhibit rust. Always lock up tools and equipment, and keep out

of reach of children.

Do not use this product if under the inuence of alcohol or drugs. 6. Read

warning labels on prescriptions to determine if your judgement or reexes are

impaired while taking drugs. If there is any doubt, do not attempt to use this

product.

Dress properly.7. Do not wear loose clothing or jewelry as they can be caught in

moving parts. Wear restrictive hair covering to contain long hair. Wear heavy

duty gloves when handling tires, but be careful to keep gloves away from all

moving parts of the Tire Changer.

Do not overreach.8. Keep proper footing and balance at all times. Do not reach

over or across running machines.

Industrial applications must follow OSHA requirements.9.

Maintain this product with care.10. Keep this product clean for better and safer

performance.

Maintenance:11. For your safety, service and maintenance should be performed

regularly by a qualied technician.

Check for damaged parts.12. Before using this product, carefully check that it will

operate properly and perform its intended function. Check for damaged parts

and any other conditions that may affect the operation of this product. Replace

or repair damaged or worn parts immediately.

Replacement parts and accessories:13. When servicing, use only identical

replacement parts. Only use accessories intended for use with this product.

Use the right tool or attachment for the job.14. Do not attempt to force a small

tool or attachment to do the work of a larger industrial tool or attachment. There

REV 07g

Page 6SKU 90589 For technical questions, please call 1-800-444-3353.

are certain applications for which this product was designed. It will do the job

better and more safely at the rate for which it was intended. Do not modify this

product, and do not use this product for a purpose for which it was not intended.

WARNING:15. The Tire Changer requires the assembly of a UL, CSA, or CE listed,

220 Volt, 3-Prong Electrical Plug (not provided) onto the unit’s electrical power

cord. The National Electric Code requires that the GREEN wire on the unit must

be used as the GROUND wire. The “HOT” wires on the power cord are the

BLACK and WHITE wires. Do not attempt to alter the 220 Volt, 3-Prong Plug or

its assembly to the power cord (as mentioned above) in any way. In addition,

it is recommended that this assembly procedure be carried out by a qualied

electrician.

CAUTION!16. Prior to performing any services or maintenance on the Tire

Changer, always disconnect the Tire Changer from its air supply source. Pump

the Bead Breaker Pedal several times to evacuate all compressed air from the

machine, and disconnect the unit from its electrical supply source.

Use only clean, dry, regulated, compressed air at up to17. 110 PSI (8-BAR).

Never use oxygen, carbon dioxide, combustible gases, or any other bottled gas

as a power source for this machine.

EXPLOSION DANGER! Never overinate tires or other inatable items. 18.

When inating a tire with compressed air, make sure to inate the tire to

the exact PSI as recommended by the tire manufacturer. Always observe

Pressure Gauge of Tire Changer to check the actual pressure in tires.

To avoid personal injury and/or machine damage, always make sure the tire19.

rim is rmly secured on the Tire Changer with its Jaws.

Never place your hands or ngers between the vehicle wheel rim and the 20.

Jaws of the Tire Changer during the locking/clamping stage.

Dispose of old tires in accordance with local, state, and federal laws.21.

People with pacemakers should consult their physician(s) before use.22.

Electromagnetic elds in close proximity to heart pacemaker could cause

pacemaker interference or pacemaker failure.

WARNING!23. The warnings, precautions, and instructions discussed in this

manual cannot cover all possible conditions and situations that may occur. The

operator must understand that common sense and caution are factors which

cannot be built into this product, but must be supplied by the operator.

REV 07g, 07k

Page 7SKU 90589 For technical questions, please call 1-800-444-3353.

UNPACKING

When unpacking, check to make sure all the parts shown on the Parts Lists

near the end of this manual are included. If any parts are missing or broken, please

call Harbor Freight Tools at the number shown on the cover of this manual as soon as

possible.

ASSEMBLY INSTRUCTIONS

Note: For additional information regarding the parts mentioned in the following pages,

refer to the Assembly Diagrams near the end of this manual.

With assistance and a proper lifting device, carefully move the Tire Changer to1.

the desired workplace location. Make sure to position the Tire Changer on a

at, level, dry, oor surface capable of bearing the weight of the Tire Changer,

operator, additional tools, tires, etc.

Using the four mounting holes located at the Tire Changer’s base as a template,2.

mark the spots where four 3/8” diameter mounting holes will be drilled in the oor

surface. Then, temporarily set the Tire Changer aside.

Drill the four, pre-marked, 3/8” holes in the oor surface (about 4” deep). Then, 3.

insert a 3/8” expansion plug (not included) in each of the four holes.

Move the Tire Changer back to its original position, making sure to align its four4.

mounting holes with the four pre-drilled holes in the oor surface. Once the holes

are aligned and the Tire Changer is level, insert four 3/8” bolts (not included)

through the mounting holes and into the expansion plugs. Secure the Tire

Changer to the oor surface by tightening the four 3/8” bolts.

Prior to assembling and using the Tire Changer, it is recommended that you5.

familiarize yourself with the main components of the unit. (See Figure A.)

NOTE:6. Prior to beginning the assembly procedures, make sure to remove

all the additional parts and accessories from the shipping boxes that are

included with the Tire Changer.

REV 07g

Page 8SKU 90589 For technical questions, please call 1-800-444-3353.

REV 07g

LOCKING HANDLE BAR (142)

HEX VERTICAL ARM (120)

MOUNTING HEAD (123)

JAW (203)

TURNTABLE (201)

BEAD LIFTING LEVER (13)

INFLATION PEDAL (IT106)

TILTING PEDAL (404)

CLAMPING PEDAL (403)

BEAD BREAKER PEDAL (402) REVERSE PEDAL (401)

RUBBER WHEEL SUPPORT (3 & 11)

SHOVEL (315)

BEAD BREAKER ARM (321)

FILTER & PRESSURE

REDUCER + LUBR. (IT207)

AIR TANK (IT1)

VERTICAL COLUMN (101)

FIGURE A

7. Vertical column assembly procedure:

With assistance, place the Column (1, Fig. B-1)1)

in its seating on the Body Assembly (2, Fig. B-1).

Push the Air Hose (3, Fig. B-1) through the large

round hole into the body.

Insert the Pin (13, Fig. B-1) through the column as2)

shown in Fig. B-1 and fasten it with Screws (14,

Fig. B-1) and Washers (15, Fig. B-1).

Using the Screw (17, Fig. B-1) tighten with the3)

Self- Locking Nut (16, Fig. B-1) to connect the Pin

(18, Fig. B-1) of the post tilting cylinder.

Remove the four Screws (4, Fig. B-1) from the left4)

Side Cover (6, Fig. B-1) and remove it. Connect

the Air Hose (3, Fig. B-1) from the column to the

6mm Connector (5, Fig. B-1).

Replace the Side Cover (6, Fig. B-1) and fasten it5)

with the Screws (4, Fig. B-1).

Install the plastic guard and x it with the two Cap 6)

Screws (10, Fig. B-1).

Fix the Metal Sheeting Guard (11, Fig. B-1) to the back of the vertical column (1, Fig.7)

B-1) using the two Cap Screws (12, Fig. B-1).

FIGURE B-1

Page 9SKU 90589 For technical questions, please call 1-800-444-3353.

SCREW (114)

KNOB (115)

SPRING (117)

SELF-LOCKING

NUT

(137)

SCREW

(129)

SCREW

(129)

SCREW

(113)

PLASTIC COVER (116)

VERTICAL LOCKING PLATE (118)

VERTICAL ARM (120)

FIGURE B-2

8. Loosen the three Screws (113 & 129). Then, lift up and remove the Plastic Cover

(116). (See Figure B-2.)

With assistance, slide the Vertical Arm (120) fully upward and hold.9. NOTE: You

may wish to place wooden blocks under the Vertical Arm in order to keep the

Vertical Arm in its upward position throughout this assembly procedure.

(See Figure B-2.)

Temporarily unscrew and remove the Self-Locking Nut (137) from the Vertical10.

Locking Plate (118). (See Figure B-2.)

Insert the Spring (117) onto the upper portion of the Vertical Arm (120), and allow11.

the Spring to rest upon the Vertical Locking Plate (118). (See Figure B-2.)

Re-tighten the Self Locking Nut (137) into the Vertical Locking Plate (118) in12.

order to secure the Spring (117) to the Vertical Locking Plate. (See Figure B-2.)

Insert the Knob (115) onto the upper portion of the Spring (117). Push the Knob13.

rmly down, while compressing the Spring, until the Knob contacts the upper

portion of the Vertical Arm (120). Then secure the Knob to the Vertical Arm,

using the Screw (114). (See Figure B-2.)

CAUTION! Use extreme caution when compressing the Spring (117).

Compressing the Spring will cause resistance which could result in

personal injury should the Spring suddenly expand. Maintain a rm grip

on the Knob (115) while compressing the Spring. Firmly tighten the Screw

(114) to secure the Knob to the Vertical Arm. (See Figure B-2.)

REV 07g

Page 10SKU 90589 For technical questions, please call 1-800-444-3353.

Re-attach the Plastic Cover (116), and re-tighten the three Screws (113 & 129).14.

If using wooden blocks to support the Vertical Arm (120), remove the blocks.

(See Figure B-2.)

NOTE:15. For shipping purposes, the Shovel (315) is restrained with a temporary

tie-down bracket. Make sure to remove and discard the bracket.

(See Figure A.)

Lay out the Tool Box (IT42) and Tool Box Support (IT38).16. (See Assy. Diagram.)

Attach the Tool Box Support (IT38) to the Body (1) of the Tire Changer, using the17.

Mounting Bracket Bolts. (See Assy. Diagram.)

Attach the Tool Box (IT42) to the Tool Box Support (IT38), using the Mounting18.

Bracket Bolts. (See Assy. Diagram.)

Remove the Left Side Cover (8) from the Body (1) to expose the inside of the Tire19.

Changer. (See Assy. Diagram.)

Run the Hose (IT15) through the opening in the Body (1) of the Tire Changer.20.

Then, connect the Hose to the 5-Way Valve (IT17).

(Note location in Assy. Diagram.)

Re-attach the Left Side Cover (8) to the Body (1) of the Tire Changer.21.

(See Assy. Diagram.)

Assembly of the Tire Changer should be complete and the machine now ready22.

to operate. Only set up and use the Tire Changer on a at, level surface that is

capable of supporting the weight of this heavy tool (566 lb.) and all required tools

and tires.

REV 07g

OPERATING INSTRUCTIONS

To Perform Preliminary Operating Tests:

Plug the Power Cord into the nearest 220 volt, grounded, electrical outlet.1.

Connect the air compressor’s supply hose (not included) to the Filter & Pressure2.

Reducer + Lubr. (IT201 thru IT205). Set the air compressor’s regulator to no

more than 110 PSI. Turn on the air compressor, and allow sufcient time for

adequate build-up of compressed air. (See Figure A.)

Depress the Reverse Pedal (401) down. The Turntable (201) should turn in a3.

clockwise direction. Pull the Reverse Pedal up, and the Turntable should turn

counterclockwise. (See Figure A.)

Open the Bead Breaker Arm (321) manually, and depress the Bead Breaker4.

Pedal (402). The Bead Breaker Arm will close. When the Bead Breaker Pedal is

released, the Pedal should return to its original position. (See Figure A.)

Table des matières

Autres manuels Central Machinery Outils électriques

Central Machinery

Central Machinery 63995 Instructions de montage

Central Machinery

Central Machinery 38119 Manuel d'installation

Central Machinery

Central Machinery 43353 Manuel utilisateur

Central Machinery

Central Machinery 45656 Manuel utilisateur

Central Machinery

Central Machinery 60238 Instructions de montage

Central Machinery

Central Machinery 42927 Mode d'emploi

Central Machinery

Central Machinery 39741 Manuel utilisateur

Central Machinery

Central Machinery 91130 Manuel utilisateur

Central Machinery

Central Machinery 32650 Manuel d'installation

Central Machinery

Central Machinery Central Machinery 13" Bench Drill Press Manuel utilisateur

Central Machinery

Central Machinery 03135 Manuel utilisateur

Central Machinery

Central Machinery 34542 Manuel utilisateur

Central Machinery

Central Machinery 31849 Guide de référence rapide

Central Machinery

Central Machinery 32966 Manuel de la liste des pièces

Central Machinery

Central Machinery 96318 Manuel utilisateur

Central Machinery

Central Machinery 05907 Guide de référence rapide

Central Machinery

Central Machinery 59490 Instructions de montage

Central Machinery

Central Machinery 42289 Guide de référence rapide

Central Machinery

Central Machinery 43378 Manuel d'installation

Central Machinery

Central Machinery 44506 Manuel d'installation

Central Machinery

Central Machinery 33497 Instructions de montage

Central Machinery

Central Machinery 92066 Manuel utilisateur

Central Machinery

Central Machinery 35570 Manuel utilisateur

Central Machinery

Central Machinery 92804 Manuel utilisateur

Manuels Outils électriques populaires d'autres marques

AEG

AEG OMNI-JS Manuel utilisateur

SIP

SIP 01533 Manuel utilisateur

Ribimex

Ribimex PRS499 Manuel utilisateur

3M Fiber Optic Connector Crimp Tool Manuel utilisateur

Ryobi

Ryobi P524 Manuel utilisateur

ROJEK

ROJEK FSN 300A Manuel utilisateur

Kemper

Kemper 1740PRO Manuel utilisateur

WABCO

WABCO OptiTire Manuel utilisateur

EINHELL

EINHELL TE-MS 18/210 Li Manuel utilisateur

Orgapack

Orgapack OR-T 85 Guide rapide

TOUGHCUT

TOUGHCUT Diamond 400 Manuel utilisateur

Yaros

Yaros PB-3603 Manuel utilisateur

Fein

Fein BSS 2.0 E Guide de configuration

Baileigh Industrial

Baileigh Industrial SS-2725 Manuel utilisateur

Milwaukee

Milwaukee 2674-20 Manuel utilisateur

Fein

Fein BLs 1.6 Manuel utilisateur

Princess

Princess Electric Multi Sharpener Manuel utilisateur

FOREDOM

FOREDOM K.1050 Manuel