Central Forge 92553 Instructions de montage

Visit our website at: http://www.harborfreight.com

Email our technical support at: [email protected] 92553

NO. 4 JACK &

MINI PLANE SET

Owner’s Manual & Safety Instructions

Save This Manual Keep this manual for the safety warnings and precautions, assembly,

operating, inspection, maintenance and cleaning procedures. Write the product’s serial number in the

back of the manual near the assembly diagram (or month and year of purchase if product has no number).

Keep this manual and the receipt in a safe and dry place for future reference. 23a

When unpacking, make sure that the product is intact

and undamaged. If any parts are missing or broken,

please call 1-888-866-5797 as soon as possible.

No portion of this manual or any artwork contained herein may be reproduced in

any shape or form without the express written consent of Harbor Freight Tools.

Diagrams within this manual may not be drawn proportionally. Due to continuing

improvements, actual product may differ slightly from the product described herein.

Tools required for assembly and service may not be included.

Read this material before using this product.

Failure to do so can result in serious injury.

SAVE THIS MANUAL.

Page 2 For technical questions, please call 1-888-866-5797. Item 92553

Specifications

#4 Jack Plane 2" Wide Blade @ 25°

Mini Block Plane 1.3" Wide Blade @ 25°

IMPORTANT SAFETY INFORMATION

1. Secure workpiece with clamps.

2. Properly assemble plane before use.

3. Sharp blade; avoid contact during set up and use.

4. Wear ANSI-approved safety goggles and heavy

duty work gloves during set up and use.

5. Keep work area clean.

6. Observe work area conditions. Do not use

tools in damp or wet locations. Do not expose

to rain. Keep work area well lighted.

7. Dress properly. Do not wear loose clothing or jewelry.

Protective, electrically nonconductive clothes and

non-skid footwear are recommended when working.

Wear restrictive hair covering to contain long hair.

8. Stay alert. Watch what you are doing, use common

sense. Do not operate any tool when you are tired.

9. Take caution as some woods contain preservatives

such as copper chromium arsenate (CCA)

which can be toxic. When working with this

type of wood, extra care should be taken to

avoid inhalation and minimize skin contact.

10. Do not overreach. Keep proper footing

and balance at all times.

11. This product is not a toy. Do not allow

children to play with or near this item.

12. Use as intended only.

13. Inspect before use; do not use if

parts are loose or damaged.

14. Store idle equipment. When not in use, tools must

be stored in a dry location to inhibit rust. Always

lock up tools and keep out of reach of children.

15. Maintain product labels and nameplates.

These carry important safety information.

If unreadable or missing, contact

Harbor Freight Tools for a replacement.

Page 3For technical questions, please call 1-888-866-5797.Item 92553

Operation

Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the beginning of this document

including all text under subheadings therein before set up or use of this product.

#4 Jack Plane

1. To remove the Blade (1), lift the Lever and remove

the Lever Cap Assembly (3) from the Plane.

2. To remove the Chip Breaker (19) from the

Blade, remove the Screw (2) from the bottom of

the Blade. The Blade can now be sharpened.

Replace the Chip Breaker (curved side towards

the Blade) and tighten the Screw when finished.

3. To install the Blade, position it with the Chip

Breaker secured, over the Lever Cap Screw (4)

and align the Blade with the bottom opening of

the Plane Body (16). Replace the Lever Cap over

the Lever Cap Screw and slide it down until the

Lever Cap Screw is aligned with the narrow part of

the opening, then tighten the Lever Cap Screw.

4. Adjust the Blade left to right by using the Blade

Adjustment Lever (9). Adjust the Blade depth by

tightening or loosening the Adjustment Knob (7).

Note: If the Blade is tilted too far to one side,

scratching and gouges can occur on the workpiece.

5. Use the planer on a scrap piece of

wood after sharpening and adjusting

to ensure it is working properly.

6. Make sure the workpiece is securely fastened down.

7. Do not force the Plane or press down on it. Cut

wood by moving the Plane forward, taking off a

little wood at a time. If the Plane does not move

forward easily, adjust the Blade farther back

into the Plane Body as explained in step 4.

Note: If the Blade isn’t planing properly, adjust

the Blade depth, or adjust Blade left to right. If the

Plane does not cut easily, inspect the Blade edge for

dulling or damage, sharpen the blade if needed.

Lever (5)

Lever Cap

Screw (4)

Blade

Adjustment

Lever (9)

Adjustment

Knob (7)

Blade (1)

Chip Breaker

(19)

Screw (2)

Plane

Body (16)

Mini Block Plane

1. To remove the Blade (1), loosen the Adjustment

Screw (4) and remove the Screw Cap (2).

2. The Blade can now be sharpened.

3. To install and adjust the Blade, position it over the

Plane Body (3) with the Screw Cap on top of it.

4. Turn the Adjustment Screw until the Blade is

held firmly in place in the desired position.

5. Make sure the workpiece is securely fastened down.

6. Do not force the Plane or press down on it. Move

it forward, taking off a little wood at a time. If the

Plane does not move forward easily, adjust the

Blade as explained in step 2 on previous page.

Note: If the Blade isn’t planing properly, loosen the

Adjustment Screw and reposition the Blade up or down.

Screw

Cap (2)

Plane

Body (3)

Adjustment

Screw (4)

Blade (1)

Page 4 For technical questions, please call 1-888-866-5797. Item 92553

Maintenance

General Tool Maintenance

1. During periods of storage, coat the bare

metal surfaces with light oil to inhibit rust.

2. This product should be assembled

and stored in a dry area.

Sharpening The Cutting Blade

1. Use an abrasive stone that is lubricated

with light oil or paraffin.

2. While wearing work gloves, use two hands,

one to grip the cutting blade to maintain the

angle. The other hand should exert an even

pressure just above the cutting edge.

3. Move the cutting blade along the abrasive stone in a

figure-eight motion. Begin on the course side of the

stone and finish sanding on the fine side. Always

keep the blade at the same angle while sharpening.

4. After sharpening the blade there may be a

ragged burr on the cutting edge of the blade.

5. Remove this burr by gently rubbing the flat

side of the blade on a fine abrasive stone.

Page 5For technical questions, please call 1-888-866-5797.Item 92553

Record Serial Number Here:

Note: If product has no serial number, record month and year of purchase instead.

Note: Some parts are listed and shown for illustration purposes only, and are not

available individually as replacement parts. Refer to UPC 193175486868.

PLEASE READ THE FOLLOWING CAREFULLY

THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY DIAGRAM

IN THIS DOCUMENT AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER OR DISTRIBUTOR

MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS

QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT, OR THAT HE OR SHE IS QUALIFIED TO REPLACE

ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/OR DISTRIBUTOR EXPRESSLY

STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND

LICENSED TECHNICIANS, AND NOT BY THE BUYER. THE BUYER ASSUMES ALL RISK AND LIABILITY

ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS

THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO.

Page 6 For technical questions, please call 1-888-866-5797. Item 92553

Parts List and Diagram

#4 Jack Plane

Part Description Qty

1 Blade 1

2 Screw 1

3Lever Cap Assembly 1

4 Lever Cap Screw 1

5 Lever 1

6Y Adjusting Lever 1

7 Adjustment Knob 1

8 Adjustment Screw 1

9 Adjustment Lever 1

10 Screw & Washer For Frog 1

Part Description Qty

11 Handle 1

12 Knob 1

13 Bolt and Nut for Handle 1

14 Bolt and Nut for Knob 1

15 Screw for Handle Toe 1

16 Plane Body 1

17 Clip & Screw for Frog 1

18 Adjustment Screw for Frog 1

19 Chip Breaker 1

Page 7For technical questions, please call 1-888-866-5797.Item 92553

Parts List and Diagram

Mini Block Plane

Part Description Qty

1 Blade 1

2 Screw Cap 1

Part Description Qty

3 Plane Body 1

4 Adjustment Screw 1

26677 Agoura Road • Calabasas, CA 91302 • 1-888-866-5797

Limited 90 Day Warranty

Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards,

and warrants to the original purchaser that this product is free from defects in materials and workmanship for the

period of 90 days from the date of purchase. This warranty does not apply to damage due directly or indirectly,

to misuse, abuse, negligence or accidents, repairs or alterations outside our facilities, criminal activity, improper

installation, normal wear and tear, or to lack of maintenance. We shall in no event be liable for death, injuries

to persons or property, or for incidental, contingent, special or consequential damages arising from the use of

our product. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the

above limitation of exclusion may not apply to you. THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER

WARRANTIES, EXPRESS OR IMPLIED, INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS.

To take advantage of this warranty, the product or part must be returned to us with transportation charges

prepaid. Proof of purchase date and an explanation of the complaint must accompany the merchandise.

If our inspection verifies the defect, we will either repair or replace the product at our election or we may

elect to refund the purchase price if we cannot readily and quickly provide you with a replacement. We will

return repaired products at our expense, but if we determine there is no defect, or that the defect resulted

from causes not within the scope of our warranty, then you must bear the cost of returning the product.

This warranty gives you specific legal rights and you may also have other rights which vary from state to state.

Table des matières

Autres manuels Central Forge Raboteuse

Central Forge

Central Forge 92553 Manuel utilisateur

Manuels Raboteuse populaires d'autres marques

Felisatti

Felisatti PF180/1500 Manuel utilisateur

DeWalt

DeWalt DW 1150 Mode d’emploi

Triton

Triton TRP UL Guide rapide

Melbourne

Melbourne MTC-49407 Manuel utilisateur

VARO

VARO POWERplus POW1520 Manuel utilisateur

Powermatic

Powermatic 209 Manuel de service

Skil

Skil 1565 Manuel utilisateur

Makita

Makita 1051D Manuel utilisateur

Scheppach

Scheppach Plana 3.0 Instructions de montage

Grizzly

Grizzly G1033X Manuel utilisateur

Stanley

Stanley STPP7502 Manuel utilisateur

Palmgren

Palmgren 84115 Manuel utilisateur

Draper

Draper PT610V Manuel utilisateur

Makita

Makita PC5000C Manuel utilisateur

Berner

Berner BP 40-82 C Manuel utilisateur

Grizzly

Grizzly G0603X Manuel utilisateur

King Industrial

King Industrial CT-381FX Manuel utilisateur

FXA

FXA FXAJD8220 Manuel utilisateur