Cassida 6600 Manuel utilisateur
Cassida Corporation • 11035 Technology Place, Suite 500 San Diego, CA 92127 • www.CassidaUSA.com
©2019 Cassida Corporation. All rights reserved. Specifications subject to change without notice. Cassida is a registered trademark of the Cassida Corporation.
REV0919
6600
Feed Gap Procedure
STEPS
We recommend following the steps below to properly adjust the feed gap of 6600.
The Cassida 6600 feed gap adjustment dials can be sensitive during adjustments. Do not overturn each adjustment or
you may overshoot the optimum gap. We recommend testing with a stack of bills after each adjustment turn.
1. Turn the power switch off and disconnect the power cord from the machine.
2. Place two moderately worn $1 bills on the hopper platform lengthwise, centered on the platform, and approximately
one inch apart.
TOOLS NEEDED NOTE:
To clean the unit, it is recommended
to use Cassida cleaning products.
Philips screwdriver
Feed gap adjustment of the unit is always performed before shipment. Sometimes during transit or after a long
period of use the feed gap might change. Feed gap that is not correctly adjusted can affect the overall
performance of the Cassida 6600, which can lead to a variety of issues such as multiple bills at the same time
being pulled into the bill feed mechanism, jamming, miscounting, and Double Note (DBL) Errors.
6600
Feed Gap Procedure
Cassida Corporation • 11035 Technology Place, Suite 500 San Diego, CA 92127 • www.CassidaUSA.com
©2019 Cassida Corporation. All rights reserved. Specifications subject to change without notice. Cassida is a registered trademark of the Cassida Corporation.
REV0919
3. Reach underneath the display panel and manually turn the feed roller shaft by hand so the bills are pulled into
the bill feed path approximately for three inches.
6600
Feed Gap Procedure
Cassida Corporation • 11035 Technology Place, Suite 500 San Diego, CA 92127 • www.CassidaUSA.com
©2019 Cassida Corporation. All rights reserved. Specifications subject to change without notice. Cassida is a registered trademark of the Cassida Corporation.
REV0919
CONTACT INFORMATION
Cassida Corporation
After Market Technical Services
Support: http://www.cassidausa.com/support
E-Mail: suppor[email protected]
NOTE:
Several factors can cause a Cassida 6600 to jam or not recognize
genuine bills:
- Overly wrinkled, overly creased, overly worn, and vandalized bills
- Foreign objects dropped or run through the bill path
- Dropping the unit or bumping into the unit during use
- A harsh change in temperature
- Extended period of non-use
- Improper maintenance or lack of preventative maintenance/cleaning
4. Gently tug on the end of each bill. There should be moderate resistance.
IMPORTANT: The left and right bills sho, uld have equal resistance.
Technical Services for further troubleshooting. Be sure to provide the following information:
a. If the bills feel too loose, tighten the feed gap by turning the adjustment screws counterclockwise with
Phillips screwdriver.
b. If the resistance feels too tight, loosen the gap by turning the screws clockwise with Phillipʼs screwdriver.
c. Adjust 1/8 turn at a time, then reconnect the power cord and turn the unit on. Retest the unit to see if it works
fine or it needs more feed gap adjustment.
Feeding gap
adjusting screw. (left)
Feeding gap
adjusting screw. (right)
Bills feel loose, tighten
feed gap (counterclockwise)
Bills feel tight, loosen
feed gap (clockwise)
Table des matières
Autres manuels Cassida Caisse enregistreuse
Cassida
Cassida 6600 Manuel
Cassida
Cassida C-880 Manuel utilisateur
Cassida
Cassida 5520 series Manuel utilisateur
Cassida
Cassida 5510 Manuel utilisateur
Cassida
Cassida 5520 UV Manuel utilisateur
Cassida
Cassida C 200 Manuel utilisateur
Cassida
Cassida Xpecto Manuel utilisateur
Cassida
Cassida InstaCheck II Manuel utilisateur
Cassida
Cassida C300 Manuel
Cassida
Cassida Xpecto LiTE Manuel utilisateur
Manuels Caisse enregistreuse populaires d'autres marques
Cashmaster
Cashmaster Sigma 105 Manuel utilisateur
Agilent Technologies
Agilent Technologies 53151A Manuel utilisateur
Cashmaster
Cashmaster Sigma 105 Manuel utilisateur
Tellermate
Tellermate TY Manuel d'utilisation et d'entretien
HYOSUNG
HYOSUNG MX-4000W Manuel utilisateur
Cashmaster
Cashmaster Sigma 105 Manuel utilisateur
