Casio FX-9750G Manuel utilisateur
Programming
19-1 Before Programming
19-2 Programming Examples
19-3 Debugging a Program
19-4 Calculating the Number of Bytes Used by a Program
19-5 Secret Function
19-6 Searching for a File
19-7 Searching for Data Inside a Program
19-8 Editing File Names and Program Contents
19-9 Deleting a Program
19-10 Useful Program Commands
19-11 Command Reference
19-12 Text Display
19-13 Using Calculator Functions in Programs
Chapter
19
314
19-1 Before Programming
The programming function helps to make complex, often-repeated calculations quick
and easy. Commands and calculations are executed sequentially, just like the manual
calculation multistatements. Multiple programs can be stored under file names for
easy recall and editing.
Select the PRGM icon in the Main Menu and enter the PRGM Mode. When you do,
a program list appears on the display.
Selected memory area
(use
f
and
c
to move)
1(EXE) ....... Execute program
2(EDIT) ...... Program edit
3(NEW) ...... New program
4(DEL) ....... Specific program delete
5(DEL•A).... Delete all
6(g) ........... Next menu
6(g)
1(SRC)....... File name search
2(REN)....... File name change
6(g) ........... Previous menu
• If there are not programs stored in memory when you enter the PRGM Mode, the
message “No Programs” appears on the display and only the NEW item (3) is
shown in the function menu.
File Name
Program
File Name
Program
File Name
Program
123456
123456
P.332
P.332
P.325
P.328
315
19-2 Programming Examples
Example 1 To calculate the surface area and volume of three regular
octahedrons of the dimensions shown in the table below
Store the calculation formula under the file name OCTA.
Length of One Side (A) Surface Area (S) Volume (V)
7 cm cm2cm3
10 cm cm2cm3
15 cm cm2cm3
The following are the formulas used for calculating surface area S and volume V of a
regular octahedron for which the length of one side is known.
2
S = 2 3 A2, V = –––– A3
3
When inputting a new formula, you first register the file name and then input the
actual program.
uu
uu
uTo register a file name
Example To register the file name OCTA
• Note that a file name can be up to eight characters long.
1. While the program list is on the display, press 3(NEW).
3(NEW)
1(RUN)....... For input of general calculation programs
2(BASE)..... For input of programs containing number base specifications
5(Q) .......... Password registration
6(SYBL) ..... Symbol menu
2. Input the name of the file.
OCTA
123456
A
P.323
316
123456
• The cursor changes form to indicate alpha character input.
• The following are the characters you can use in a file name:
Athrough Z, r,
θ
, spaces, [, ], {, }, ’, ”, ~, 0 through 9, ., +, –, ×, ÷
• Note, however, that vand .cannot be input for the name of a program that
contains binary, octal, decimal, or hexadecimal calculations.
• Use 1(RUN) to input a program for general calculations (a program to be ex-
ecuted in the COMPMode). For programs that involve number system specifica-
tions, use 2(BASE). Note that programs input after pressing 2(BASE) are
indicated by Bto the right of the file name.
• Pressing 6(SYBL) displays a menu of symbols that can be input.
6(SYBL)
• You can delete a character while inputting a file name by moving the cursor to the
character you want to delete and pressing D.
3. Press wto register the file name and change to the program input screen.
w
• Registering a file name uses 17 bytes of memory.
• The file name input screen remains on the display if you presswwithout input-
ting a file name.
• To exit the file name input screen and return to the program list without register-
ing a file name, press J.
• When you register the name of a program that contains binary, octal, decimal, or
hexadecimal calculations, the indicator Bis appended to the right of the file
name.
uu
uu
uTo input a program
Use the program input screen to input the contents of a program.
1(TOP) ....... Top of program
2(BTM)....... Bottom of program
3(SRC)....... Search
4(MENU).... Mode menu
6(SYBL) ..... Symbol menu
123456
P.328
P.328
P.327
19 - 2 Programming Examples
File name
P.5
317
uu
uu
uTo change modes in a program
• Pressing 4(MENU) while the program input screen is on the display causes a
mode change menu to appear.You can use this menu to input mode changes into
your programs. For details on each of these modes, see “To select an icon”, as
well as the sections of this manual that describe what you can do in each mode.
4(MENU)
6(g)
• The following menu appears whenever you press 4(MENU) while inputting a
program that involves number base specifications.
4(MENU)
• Pressing 6(SYBL) displays a menu of symbols that can be input into a pro-
gram.
6(SYBL)
• Pressing !Zdisplays a menu of commands that can be used to change set
up screen settings inside a program. For details on each of these commands,
see “To change a mode set up”.
!Z
6(g)
6(g)
6(g)
123456
123456
123456
123456
123456
123456
123456
123456
P.5
Programming Examples 19 - 2
318
The following function key menu appears if you press !Z while inputting a
program that contains binary, octal, decimal, or hexadecimal calculation.
!Z
Actual program contents are identical to manual calculations. The following shows
how the calculation of the surface area and volume of a regular octahedron would be
calculated using a manual calculation.
Surface Area S .. c*!9d* <value ofA> xw
Volume V ........... !9c/d* <value of A> Mdw
You could also perform this calculation by assigning the value for the length of one
side to variableA.
Length of One Side A
............ <value of A> aaAw
Surface Area S .. c*!9d*aAxw
Volume V ........... !9c/d*aAMdw
If you simply input the manual calculations shown above however, the calculator
would execute them from beginning to end, without stopping. The following com-
mands make it possible to interrupt a calculation for input of values and display of
intermediate results.
?:This command pauses program execution and displays a question mark as a
prompt for input of a value to assign to a variable. The syntax for this command
is: ? →<variable name>.
^^
^^
^:This command pauses program execution and displays the last calculation re-
sult obtained or text. It is similar to pressing win a manual calculation.
• For full details on using these and other commands, see “Useful Program Com-
mands”.
The following shows examples of how to actually use the ? and ^commands.
!W4(?)aaA6(g)5(:)
c*!9d*aAx
6(g)5(^)
!9c/d*aAMd
!Q or JJ
P.333
123456
19 - 2 Programming Examples
123456
319
uu
uu
uTo run a program
1. While the program list is on the display, use fand cto highlight the name of
the program you want to run.
2. Press 1(EXE) or wto run the program.
Let’s try running the program we input above.
Length of One Side (A) Surface Area (S) Volume (V)
7 cm 169.7409791 cm
2
161.6917506 cm
3
10 cm 346.4101615 cm
2
471.4045208 cm
3
15 cm 779.4228634 cm
2
1590.990258 cm
3
1(EXE) or w
hw
(Value of A)
Intermediate result produced by
^
w
w
baw
123456
Programming Examples 19 - 2
320
w
• Pressing wwhile the program’s final result is on the display re-executes the
program.
• You can also run a program while in the RUN Mode by inputting:
Prog ”<file name>” w.
• An error (Go ERROR) occurs if the program specified by Prog ”<file name>”
cannot be found.
19 - 2 Programming Examples
P.334
321
19-3 Debugging a Program
A problem in a program that keeps the program from running correctly is called a
“bug,” and the process of eliminating such problems is called “debugging.” Either of
the following symptoms indicates that your program contains bugs and that debug-
ging is required.
• Error messages appearing when the program is run
• Results that are not within your expectations
uu
uu
uTo eliminate bugs that cause error messages
An error message, like the one shown below, appears whenever something illegal
occurs during program execution.
When such a message appears, press dor eto display the location where the
error was generated, along with the cursor. Check the “Error Message Table” for
steps you should take to correct the situation.
• Note that pressing dor ewill not display the location of the error if the pro-
gram is password protected.
uu
uu
uTo eliminate bugs that cause bad results
If your program produces results that are not what you normally expect, check the
contents of the program and make necessary changes. See “Editing File Names
and Program Contents” for details on how to change program contents.
P.399
P.323
P.328
322
19-4 Calculating the Number of Bytes Used by a
Program
This unit comes with 26 kbytes of memory. A byte is a unit of memory that can be
used for storage of data.
There are two types of commands: 1-byte commands and 2-byte commands.
• Examples of 1-byte commands: sin, cos, tan, log, (, ),A, B, C, 1, 2, etc.
• Examples of 2-byte commands: Lbl 1, Goto 2, etc.
While the cursor is located inside of a program, each press of dor ecauses the
cursor to move one byte.
• You can check how much memory has been used and how much remains at any
time by selecting the MEM icon in the Main Menu and entering the MEM Mode.
See “Memory Status (MEM)” for details.
P.28
Autres manuels pour FX-9750G
22
Table des matières
Autres manuels Casio Calculatrice
Casio
Casio fx-83 Mode d’emploi
Casio
Casio fx-350MS Manuel d'installation et d'exploitation
Casio
Casio fx-100AU PLUS Manuel utilisateur
Casio
Casio SL-210TE Manuel utilisateur
Casio
Casio FX-9750GII - SOFTWARE VERSION 2-00 Manuel utilisateur
Casio
Casio fx-7400G PLUS Document technique
Casio
Casio DATA-CAL DC-150 Manuel utilisateur
Casio
Casio fx-5500L Manuel utilisateur
Casio
Casio fx-7400G Manuel utilisateur
Casio
Casio FX-702P Manuel utilisateur
Casio
Casio FX-9860GII - SOFTWARE VERSION 2-00 Manuel utilisateur
Casio
Casio ALGEBRA FX 2.0 Manuel utilisateur
Casio
Casio Prizm Manuel utilisateur
Casio
Casio FC-200 Manuel utilisateur
Casio
Casio FX-9750GII - SOFTWARE VERSION 2-00 Manuel utilisateur
Casio
Casio DR-420TER Manuel utilisateur
Casio
Casio DR-220TA Manuel utilisateur
Casio
Casio FX-P401 Manuel utilisateur
Casio
Casio OH-7000G Manuel utilisateur
Casio
Casio ALGEBRA FX 2.0 Manuel utilisateur
