Cary Audio Design CAD-280 SA V-12R Manuel utilisateur

Cary Audio Design

CAD-280SA

V-12R

Vacuum Tube Stereo or

Monobloc Power Amplifiers

OPERATION MANUAL

NOTE: Before installing your new V-12R power amplifier, please read this manual carefully as it will

inform you of the specifications, proper installation procedures and operation procedures. Also included

in this manual are guidelines on how to properly service and care for your new CAD-280 SA (V-12R)

stereo or mono power amplifier.

Specifications for your newV-12R power amplifier.

We have updated the V-12 mono and stereo models to a RACING (R) version! The

new racing input circuit makes the input sensitivity 1.2 volts, similar to most

components currently available. Operating the power amplifier is a simple procedure.

Each unit is designed for long term stability in virtually any home operating situation.

Please note, if the unit is operated outside the parameters outlined in this owner's

manual, damage may result. Please read this manual carefully before putting your new

V-12R in operation. The following definitions are applicable. Warnings should be

followed explicitly.

1.2 Specifications

The CAD-280 SA V-12R or V-12R Monobloc version basic specifications:

DIMENSIONS: 9’’H x 12 _’’W x 20’’D

WEIGHT: 68-lb. stereo or 85-lb. for the Monobloc version

CIRCUIT TYPE: Push-Pull Triode or Ultra-linear Amplification in Pure Class A

POWER OUTPUT: 50 watts – Triode Mode 100 watts – Triode (Mono)

100 watts – Ultralinear Mode 200 watts – Ultralinear (Mono)

INPUT SENSITIVITY: 1.3 volts for full output

INPUT IMPEDANCE: 150,000 ohms

NOISE AND HUM: > 84db below rated output

FREQUENCY RESPONSE: 20Hz to 23Khz +/- 1.0 dB (at full power)

TUBES: 2- 12BZ7 Input tubes (or 12AY7, 12AX7)

2- EL-84 Current Source tubes (or 6BQ5)

12- EL-34 Output tubes (or 6550, KT-66, KT-77, KT-88, KT-

90, 6L6)

POWER TRANSFORMER: 1- EI laminated, 200% duty cycle

OUTPUT TRANSFORMERS: 2-EI laminated stereo (1-EI mono) Silicon Impregnated

RESISTORS: 1.0% tolerance, precision metal film resistors

CAPACITORS: Oil Filled

POWER SUPPLY CAPACITORS: 4 - 560 MFD @ 400 volts

AC CORD: 3 conductor shielded detachable

AC POWER REQUIREMENTS: 117/234 volts AC 50/60Hz

POWER CONSUMPTION: 420 watts in operation, 10 watts in stand-by

WARM-UP TIME: 3 minutes

BREAK-IN PERIOD: 100 hours of music playing time

FINISH: Jaguar Carnival Red paint on chassis

FRONT PANEL: Machined, Black Anodized aluminum

Specifications are subject to improvement without notice or obligation.

WARNING

HAZARD PRESENTS PERSONAL INJURY OR DEATH

Caution

EQUIPMENT DAMAGE MAY OCCUR BUT NOT PERSONAL INJURY

Note

Proper performance of the amplifier cannot be ensured

if disregarded

1.3 Front Panel Features

POWER ON/OFF SWITCH: AC mains switch and high voltage in “ON” position

HV LED: Indicates the high voltage supply is ON and the fuse is intact.

BIAS L led: Indicates the Bias voltage for Left channel (Left chassis side for Mono)

BIAS R led: Indicates the Bias voltage for Right channel (Right chassis side for Mono)

OPERATE/STANDBY SWITCH: Turns filaments on in the “OPERATE” position.

1.4 Rear Apron Features

INPUTS RCA or XLR: Signal input connection via shielded interconnect cable

RCA/ XLR SWITCH: Switches between RCA and XLR input selection.

SPEAKER OUTPUT: Three- 5-way binding posts provide the signal output to the

speaker system. Red = +, 4 or 8 ohms, Black = -, ground

BIAS JACK: _” ‘phone plug’ jack for supplied cable with plug to measure the output

tube bias levels. See tube bias instruction sheet later in the manual.

BIAS POTENTIOMETER: Adjusts to achieve the bias level setting for the output tubes.

AC: 3- conductor shielded power detachable cord to AC power mains.

POWER AC FUSE: This is an over current protection fuse for the power transformer.

Never replace with any other fuse than 3 AMP SLOW BLOW!

250 VOLT! (2 AMP SLOW BLOW IN 220 VAC OPERATION)

FILAMENT FUSE: This is an over current protection fuse for the filament transformer.

Never replace with any other fuse than a 2 AMP SLOW BLOW!

(1 AMP SLOW BLOW IN 220 VAC OPERATION.)

LEFT AND RIGHT TUBE (side) FUSE: This is a protection fuse for the output tubes.

Never replace it with any other fuse than a 0.5 amp fast blow! 0.5A @ 250 volt rating.

1.5 TOP PANEL FEATURES

TRIODE / ULTRA-LINEAR SWITCHES: Three mode switches per chassis side allow

you to choose from 50 watts (100 watts mono) power in Triode mode or 100 watts

(200 watts mono) power in Ultralinear mode. All mode switches should be set to the

same ‘direction.’

RED LED: (‘Good Health LED’) Indicator for each individual output tube. When the

LED is lit it shows that the associated output tube is working.

CAUTION

EQUIPMENT DAMAGE MAY OCCUR WITH IMPROPER RATED FUSES

CAUTION

NEVER REMOVE or THE INSERT AC LINE CORD WHEN THE UNIT IS ON TO

AVOID RISK OF ELECTRICAL SHOCK

INSTALLATION

This section describes the unpacking and installation procedures for the CAD-280 SA

amplifier.

2.1 Unpacking

All shipping containers have been specifically designed to protect their contents and

special care has been taken to prevent damage under normal shipping conditions.

Mishandling should be evident upon inspection of the shipping container. If chassis

damage is found after a visual inspection, take care not to destroy the evidence. If

necessary, document the damage with photographs and contact the transport carrier

immediately. Carefully remove your new power amplifier from its packing carton, and

examine it closely for signs of shipping damage. It is recommended to save all the

original packing cartons to protect your amplifier from damage should you wish to

store it or ship it for after-sales service.

2.2 Warranty Card

Fill out the enclosed warranty registration card and return it to Cary Audio Design, Inc.

within 15 days of original purchase. Keep your original sales slip from your Cary Audio

Authorized Dealer with the packing cartons should you ever need it. Failure to register your

warranty will set the limited warranty time period to 90 days from date of purchase. When

purchased from a Cary Audio Authorized Dealer and properly registered, the limited

warranty period is extended. See the limited statement of warranty for details.

2.3 Amplifier Placement

In general, the location of your new V-12R is not critical. Certain precautions must be

taken to ensure optimum performance however. Always avoid extremely hot locations

such as near steam heat radiators or other heating units. Allow 10-12 inches above the

amplifier for proper ventilation. Keep the top of the amplifier clear of books, paper or

other equipment to protect it against overheating! DO NOT place your amplifier in a

closed book case - overheating will damage the amplifier!

2.4 Power Requirements

The CAD-280 SA is designed to operate from house current AC mains. The design

voltage is 117 VAC at 50/60Hz. (Foreign units 234 VAC at 50/60Hz.)

2.5 Cables

WARNING!

MAKE NO ATTEMPT TO PUT THE CAD-280 SA AMPLIFIER IN

SERVICE WITHOUT THE BOTTOM PLATE ATTACHED -

CONTACT WITH HIGH VOLTAGE INSIDE THE CHASSIS CAN BE

FATAL!

The speaker cables from the output posts of the CAD-280 SA to the speaker system

can be any convenient length your set-up requires. Select speaker cables of sufficient

size to preserve the outstanding performance capabilities of your power amplifier.

Heavy gauge #14 wire is suitable for distances up to 15 feet, #12 wire for up to 30 feet.

Your Authorized Cary Audio Dealer will have proper speaker cable in stock for this

purpose.

Signal input connection is made via the input jack(s) on the rear of the CAD-280 SA.

The interconnect cable(s) from the output of a variable output CD player or

preamplifier can be any convenient length your set-up requires. The choice of a

shielded, high quality interconnect cable is important. Once again, your audio dealer

will suggest and have the proper cables in stock for this purpose.

3.1 Operation

Your new power amplifier is ready for operation after the speaker, interconnect cables

and the vacuum tubes have been installed into their proper sockets. Refer to the tube

placement sheet at the end of this manual for proper tube installation. On the

amplifiers rear panel please select either the RCA or XLR input(s), according to your

installation.

3.2 4 or 8 OHM Speaker Binding Posts

Select the proper speaker binding post (4 or 8 ohm) for the speaker(s) in your system.

The selection should be based on your current speakers’ rated specifications and

listening tests to confirm the correct connection.

3.3 Triode or Ultra-Linear Mode Switches

Select either the “Triode” 50 (100 Mono) watts or “Ultra-Linear” 100 (200 Mono)

watts output setting. Make sure all six switches are set to the same operating mode

position. You can switch between the operating modes while playing music at a

moderate volume level. Flipping one mode switch at a time is OK.

3.4 Power ON and Standby Operate Switches

Flip the power switch to the “On” position and then flip the standby switch to the

“Operate” position. Observe that all 16 vacuum tubes are lit, after a delay of 10-15

seconds. When the power tubes start to conduct, red ‘Good Health’ LED’s on the top

panel will light up next to each one. This might take 30-45 seconds delay.

3.5 The Break-In Period

The tubes, capacitors and output transformers take approximately 100 hours use to

settle in for peak performance. The V-12R will sound good right out of the box but it

will improve within a short time. After the first 50-100 hours you will notice increased

depth and tighter bass. This break-in period defies engineering theory perhaps, but we

believe it is true with quality audio amplifiers.

3.6 Bias Measurement

The bias is factory preset. It is a good idea to measure it during the initial setup to make

sure it is set to the specifications provided at the end of this manual. The AC voltage

may be different from one area to the next. Follow the instructions provided. (250-275

mA is the recommended bias setting range, per side, with 220 mA being the minimum

suggested bias level setting) Make certain to set the test meter used to mA range.

SERVICE AND CARE

4.1 CAD-280 SA (V-12R) Care and Cleaning

The case and front of the amplifier may be cleaned with a soft cloth and Windex or a

window cleaner. Moisten the cleaning rag; do not get the amplifier wet. The relative

frequency of cleaning will be governed by the operating environment cleanliness. The

chassis is best polished with non-abrasive car wax.

4.2 Tube Replacement

If it becomes necessary to replace the tubes in the amplifier, a matched set of output

tubes of the same name brand should be used. A new tube kit is available from Cary

Audio. You should get a few years or more from the output tubes with everyday usage

and many years of use from the smaller 12BZ7 and EL-84 tubes. Other types of output

tubes may be used in the V-12R power amplifiers; 6L6, 6V6, KT-66, KT-88, 6550C, KT-

90, KT-99 or EL-34 tubes are all acceptable for use in the output stage.

4.3 IN FACTORY SERVICE

Careful consideration has been given to the design of your V-12R amplifier to keep

maintenance problems to a minimum. However, it is possible that some problems may

arise which cannot be cured by a vacuum tube substitution. At this point we suggest you

contact our Customer Service Department phone number (919) 355-0010 to describe

your problem in detail. DO NOT return the amplifier to the factory without a return

authorization number (RMA) from the Customer Service Department. Please always

use the ORIGINAL PACKING BOXES from Cary to ship your amplifier for moving or

for service. Cary Audio Design, Inc. will assume no responsibility if the transportation

or shipping company refuses to pay a damage claim due to your improper packing or

lack of insurance should the unit be lost or damaged in shipment.

All mentions of in factory service are relevant for Cary Audio Design products purchased

and used exclusively within the USA only. Non USA distributors of Cary Audio Design

products will establish their own local warranty or after service policies. Ask your

dealer about local warranty policies in your locale, if you reside outside the USA.

WARNING

MAKE SURE AMPLIFIER IS UNPLUGGED FROM AC MAINS BEFORE

SERVICING

! PLEASE OBSERVE THE SAFETY DIRECTIONS IN THIS MANUAL TO

AVOID POSSIBLE ELECTRICAL SHOCK OR EQUIPMENT FAILURE

DUE TO IMPROPER INSTALLATION!

Cary Audio Design

1020 Goodworth Drive

Apex, North Carolina 27539

Tel: 919-355-0010

Fax: 919-355-0013

www.caryaudio.com

[email protected]

WARNING!

MAKE NO ATTEMPT TO PUT THE CAD-280 SA IN SERVICE WITH THE

BOTTOM PLATE REMOVED. CONTACT WITH THE HIGH VOLTAGES

FOUND INSIDE THE CHASSIS CAN BE FATAL!

COMPLETELY REMOVE AC POWER PLUG FROM THE WALL AND

ALLOW 30 MINUTES FOR THE HIGH VOLTAGE CAPACITORS TO

DISCHARGE THROUGH BLEEDER RESISTORS BEFORE ATTEMPTING

TO CHANGE TUBES OR CLEAN THE INSIDE OF THE AMPLIFIER.

CAUTION

NEVER REMOVE OR INSERT AC PLUG WHEN THE UNIT IS ON OR

THE AC POWER SWITCH IS IN THE ON POSITION. OBSTRUCTION

OF THE TOP PORTION OF THE CAD-280 SA WILL RESULT IN TUBES

OVERHEATING AND DAMAGE TO THE AMPLIFIER.

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Cary Audio Design Amplificateur

Cary Audio Design

Cary Audio Design 7.25 Manuel utilisateur

Cary Audio Design

Cary Audio Design SLP-94 Manuel utilisateur

Cary Audio Design

Cary Audio Design CAD-80 Mk-II Manuel utilisateur

Cary Audio Design

Cary Audio Design CAD 808 Manuel utilisateur

Cary Audio Design

Cary Audio Design SLA-70B Signature Manuel utilisateur

Cary Audio Design

Cary Audio Design CAD-211M Manuel utilisateur

Cary Audio Design

Cary Audio Design Full Balanced Power Amplifier 2.125 Manuel utilisateur

Cary Audio Design

Cary Audio Design SLI-30 Manuel utilisateur

Cary Audio Design

Cary Audio Design Cinema P-7 Manuel utilisateur

Cary Audio Design

Cary Audio Design CAD-805 Anniversary Edition Instruction manuelle

Cary Audio Design

Cary Audio Design SLP 05 Manuel utilisateur

Cary Audio Design

Cary Audio Design SLP 90 Manuel utilisateur

Cary Audio Design

Cary Audio Design SA-200.2 Manuel utilisateur

Cary Audio Design

Cary Audio Design CAD-50M MkIII Manuel utilisateur

Cary Audio Design

Cary Audio Design CAD2A3 Manuel utilisateur

Cary Audio Design

Cary Audio Design CAD-300S SE Manuel utilisateur

Cary Audio Design

Cary Audio Design PH-302 MkII Manuel utilisateur

Cary Audio Design

Cary Audio Design CAI 1 Manuel utilisateur

Cary Audio Design

Cary Audio Design CAD 2A3 SE Manuel utilisateur

Cary Audio Design

Cary Audio Design CAD-300M Manuel utilisateur

Cary Audio Design

Cary Audio Design CINEMA 6 Manuel utilisateur

Cary Audio Design

Cary Audio Design C 306 Manuel utilisateur

Cary Audio Design

Cary Audio Design CAD-308 SA Fiche technique

Cary Audio Design

Cary Audio Design CAD2A3 Manuel utilisateur

Manuels Amplificateur populaires d'autres marques

ASTRO

ASTRO HVO V40 P Manuel utilisateur

Marantz

Marantz SUPERSCOPE BLA-545 Instructions de montage

NAD

NAD CI980 Manuel utilisateur

Technics

Technics SE-CH770 Manuel utilisateur

Harman Kardon

Harman Kardon HK6300 Manuel utilisateur

NAD

NAD T975 Manuel utilisateur

McIntosh

McIntosh MA6850 Manuel utilisateur

Electro-Harmonix

Electro-Harmonix ENGLISH MUFF’N Manuel utilisateur

Viatron

Viatron Autrix Manuel utilisateur

GME

GME GA9800 Manuel utilisateur

Atlas

Atlas CP700 Manuel utilisateur

Roland

Roland KC-1000 Manuel utilisateur

Pyle

Pyle PFMRA350BW Manuel utilisateur

Advantage

Advantage S-250 Manuel utilisateur

IRT Electronics

IRT Electronics DVA-3007 Manuel utilisateur

Dimavery

Dimavery BA-100 Series Manuel utilisateur

Sony

Sony XM-S400D Manuel utilisateur

Schertler

Schertler ROY X Manuel utilisateur