Carrier TC -PAC Manuel utilisateur
T C --- P A C , T C --- N A C
T C --- P H P, T C --- N H P
Comfort™ Series
AC / HP Thermostat
Installation Instructions
A07051 A07050
Comfort Series Comfort Series
Programmable Thermostat Non--Programmable Thermostat
Designed and Assembled in the U.S.A.
NOTE: Read the entire instruction manual before starting the installation.
US patents: US20060165149 A1, USD582803 SI, USD582802 SI
1
TABLE OF CONTENTS
PAGE
SAFETY CONSIDERATIONS 2................................
INSTALLATION CONSIDERATIONS 4..........................
INSTALLATION 5...........................................
Step 1 — Thermostat Location 5...............................
Step 2 — Install Thermostat 5..................................
Step 3 — Set Thermostat Configuration 10.......................
Step 4 — Check Thermostat Operation 18........................
FEATURES AND ACCESSORIES 20............................
OPERATIONAL AND CONNECTION INFORMATION 22..........
WIRING DIAGRAMS 25......................................
THERMOSTAT CONFIGURATION RECORD 32..................
2
SAFETY CONSIDERATIONS
Read and follow manufacturer instructions carefully. Follow all local electrical
codes during installation. All wiring must conform to local and national electrical
codes. Improper wiring or installation may damage thermostat.
Recognize safety information. This is the safety--alert symbol . When you see
this symbol on the equipment and in the instruction manual, be alert to the potential
for personal injury.
Understand the signal words DANGER,WARNING,andCAUTION.These
words are used with the safety--alert symbol. DANGER identifies the most serious
hazards which will result in severe personal injury or death. WARNING signifies a
hazard which could result in personal injury or death. CAUTION is used to identify
unsafe practices which may result in minor personal injury or product and property
damage. NOTE is used to highlight suggestions which will result in enhanced
installation, reliability, or operation.
3
INTRODUCTION
Carrier’s ComforttSeries programmable thermostats are wall--mounted,
low--voltage thermostats which maintain room temperature by controlling the
operation of a heating and/or air conditioning system. Both heat pump and air
conditioner models are available, each in programmable and non--programmable
versions. A variety of features are provided including battery operation, separate
heating and cooling setpoints, auto changeover, keypad lockout, backlighting, and
built--in installer test. Programming features include 7--day (all days the same) and
5/2 (Mon--Fri and Sat--Sun) with 2 or 4 periods per day.
This Installation Instruction covers installation, configuration, and start--up of all
four versions of the Comfort Series line of thermostats. For operational details,
consult the Owner’s Manual for the specific thermostat you are installing.
4
INSTALLATION CONSIDERATIONS
Models
There are four models in the Comfort Series: programmable and non--programmable,
AC and HP. Models TC--PAC and TC--NAC are designed for AC systems, controlling
one stage of cooling and one stage of heating. They will not operate a heat pump.
Models TC--PHP and TC--NHP are designed for HP systems, controlling two stages of
cooling and three stages of heating. They can be converted to AC operation. Select the
appropriate model for the intended application.
Power
All Comfort Series models are dual powered. They can operate from batteries or
24VAC power. Operation from 24VAC is preferred if available. Battery operation is
used when there are not enough wires to support 24VAC operation or when
“armchair programming” is desired. For an AC system, up to six wires are needed
for 24VAC operation and one less wire for battery operation. For a HP system, up to
seven wires are needed for 24VAC operation and one less wire would be sufficient
for battery operation. For heat only operation with batteries, only two wires are
required. When battery operation is used, the C terminal does not need to be
connected.
Provision is also made for separate heating and cooling transformers via separable Rc
and Rh terminals which are connected via factory--installed jumper wire.
5
INSTALLATION
Installation Notes:
SThe maximum wire size to be used in the installation is 22AWG
(0.50mm2)with 0.8mm insulation
SNo part of the control should be installed directly outdoors or in a cabin-
et outdoors
SThe control assembly should be mounted before wires are attached
Step 1 — Thermostat Location
SApproximately 5 ft (1.5m) from floor.
SClose to or in a frequently used room, preferably on an inside partition-
ing wall.
SOn a section of wall without pipes or duct work.
Thermostat should NOT be mounted
SClose to a window, on an outside wall, or next to a door leading to the
outside.
SExposed to direct light or heat from the sun, a lamp, fireplace, or other
temperature--radiating objects which could cause a false reading.
SClose to or in direct airflow from supply registers and return--air re-
gisters.
SIn areas with poor air circulation, such as behind a door or in an alcove.
6
Step 2 — Install Thermostat
ELECTRICAL OPERATION HAZARD
Failure to follow this warning could result in personal injury or
death.
Before installing thermostat, turn off all power to equipment. There
may be more than one power disconnect.
!WARNING
1. Turn OFF all power to unit.
2. If an existing thermostat is being replaced:
a. Remove existing thermostat from wall.
b. Disconnect wires from existing thermostat, one at a time. Be careful not
to allow wires to fall back into the wall.
c. As each wire is disconnected, record wire color and terminal marking.
d. Discard or recycle old thermostat.
ENVIRONMENTAL HAZARD
Failure to follow this caution may result in environmental damage.
Mercury is a hazardous waste. Federal regulations require that
Mercury be disposed of properly.
CAUTION
!
3. Open thermostat (mounting base) to expose mounting holes. The base can
be removed to simplify mounting. Press the thumb release at the top of the
7
thermostat and snap apart carefully to separate mounting base from re-
mainder of thermostat.
4. Route thermostat wires through large hole in mounting base. Level mounting
base against wall (for aesthetic value only—thermostat need not be level for
proper operation) and mark wall through four mounting holes. To avoid unin-
tended bending of wall plate plastic, all four screws and anchors must be used.
See Fig. 1.
A07153
Fig. 1 -- Backplate Mounting
5. Drill four 3/16--in. mounting holes in wall where marked.
6. Secure mounting base to wall with four screws and anchors provided. To
avoid unintended bending of wall plate plastic, all four screws and anchors must
be used. Make sure all wires extend through hole in mounting base.
8
7. Adjust length and routing of each wire to reach proper terminal and con-
nector block on mounting base with 1/4--in. (6 mm) of extra wire. Strip only
1/4 in. of insulation from each wire to prevent adjacent wires from shorting
together when connected. See Fig. 2.
A07155
Fig. 2 -- Secure Wires to Terminal Strip
8. Match and connect equipment wires to proper terminals of the connector blocks
(see Fig. 3). If there are separate 24VAC transformers, one in the indoor unit
and one in the outdoor unit, connect the common of each to the C terminal.
Remove factory--installed jumper wire from Rc and Rh terminals. Connect the
R from the indoor unit to the Rh terminal. Connect the R from the outdoor unit
to the Rc terminal. Then the W signal is taken from the Rh power and the Y1,
Y/Y2, G and O signals are taken from the Rc power.
Ce manuel convient aux modèles suivants
9
Table des matières
Autres manuels Carrier Thermostat
Carrier
Carrier 53DFS250-HW Manuel utilisateur
Carrier
Carrier Infinity Control Home Instructions de montage
Carrier
Carrier 33CS Instructions et recettes
Carrier
Carrier Cor Manuel utilisateur
Carrier
Carrier AQUAZONE 50QE900 Manuel utilisateur
Carrier
Carrier 33CS Manuel utilisateur
Carrier
Carrier 53DFS250-SL Manuel utilisateur
Carrier
Carrier Programmable Thermostats Instructions et recettes
Carrier
Carrier TSTATCCPS701 Manuel utilisateur
Carrier
Carrier Aquazone 50QE900-NPWS Manuel utilisateur
Carrier
Carrier AC Instructions et recettes
Carrier
Carrier ETN Manuel utilisateur
Carrier
Carrier 33CS220-LA Manuel utilisateur
Carrier
Carrier 33CS Manuel utilisateur
Carrier
Carrier Infinity SYSTXCCITW01 Manuel utilisateur
Carrier
Carrier TC-PHP Manuel utilisateur
Carrier
Carrier TP-WEM01 Manuel utilisateur
Carrier
Carrier Thermidistat Manuel utilisateur
Carrier
Carrier P374-1500 Manuel utilisateur
Carrier
Carrier TB-PAC Manuel utilisateur
Manuels Thermostat populaires d'autres marques
EWELLY
EWELLY EW-181 Manuel utilisateur
Prolon
Prolon T1100 Instructions d'installation
Computherm
Computherm Q20 Manuel utilisateur
Heatmiser
Heatmiser neoStat Manuel utilisateur
Aube Technologies
Aube Technologies TH111GFCI-NP 240 VCA Manuel utilisateur
Mars
Mars HEAT CONTROLLER IR Wireless Thermostat Manuel utilisateur
