Canon Nippon Maru Manuel utilisateur
©Canon Inc. ©M. Nishiguchi/SENAUN
Ships of the world : Nippon Maru : Assembly Instructions
http://www.canon.com/c-park/en/
Assembly Instructions
Mountain fold(dotted line)
Make a mountain fold.
Valley fold(dashed and dotted line)
Make a valley fold.
Scissors line(solid line)
Cut along the line.
Cut in line(solid line)
Cut along the line.
Glue spot(Red dot)
Glue parts with the same number together.
Glue spot(Green dot)
Glue within the same part.
Glue spot(Blue dot)
Glue to the rear of the other part.
Glue
The glue spot(colored dot)
shows where to apply the glue.
Tools and materials
Assembly tip
Caution
Scissors, set square, glue(We recommend stick glue), pencil, used
ballpoint pen, toothpicks, tweezers, (useful for handling small parts)
Before gluing, crease the paper along mountain fold and valley
fold lines and make sure rounded sections are nice and stiff.
Glue, scissors and other tools may be dangerous to young children
so be sure to keep them out of the reach of young children.
View of completed model
Assembly Instructions : Six A4 sheets (No. 1 to No. 6)
*Hint: Trace along the folds with a ruler
and an exhausted pen (no ink) to get a sharper, easier fold.
* Build the model by carefully reading the Assembly Instructions , in the parts sheet page order.
* This model was designed for Papercraft and may differ from the original in some respects.
Before starting assembly:
Writing the number of each section on its back side before cutting out the sections is highly recommended.
(* This way, you can be sure which section is which even after cutting out the sections.)
The parts used will vary somewhat, depending on whether the completed vessel will be modeled to depict
a ship facing wind from the left (with the bow pointed to the right) or from the right (with the bow pointed to
the left). First decide where you want to display the completed vessel, then decide whether the bow should
point to the left or right.
Bow pointed to the right (A - standard parts)
Bow pointed to the left (B - optional parts)
Indicates sections that should be glued first,
then cut out.
Indicates sections that should be folded once,
then unfolded.
After folding the part once and gluing the two
folds together, cut out from the yellow area.
Glue parts 2 and 3 together in
the same way.
Indicates where sections should
be glued together.
Indicates where to insert sections.
Do not glue the sections together.
©Canon Inc. ©M. Nishiguchi/SENAUN
Ships of the world : Nippon Maru : Assembly Instructions
Glue the rear sides of
these parts together.
Parts
Part
(bow pointed to the right) or
(bow pointed to the left; optional part)
After folding this part, unfold and
cut out from the cream-colored area.
Attach part 12 after
first gluing part 11 to part 8.
Insert until
the corners meet.
Affix parts 15, 19, and 23 to the mast by gluing
them to the positions shown in the illustration.
Cut notches all the way
to the red lines.
©Canon Inc. ©M. Nishiguchi/SENAUN
Ships of the world : Nippon Maru : Assembly Instructions
Cut away the yellow area.
Cut away this area for part 35 in the same way.
Glue these parts together.
Glue the rear sides of these parts together.
©Canon Inc. ©M. Nishiguchi/SENAUN
Ships of the world : Nippon Maru : Assembly Instructions
Fold in the tabs on part 35 and glue
in the spots indicated by the arrows.
After inserting part 36 into part 35, glue
the untreated tabs on the main vessel body.
Curl this part.
Bottom of vessel
©Canon Inc. ©M. Nishiguchi/SENAUN
Ships of the world : Nippon Maru : Assembly Instructions
As shown in the illustration,
use A parts (standard parts)
for parts 44 - 46 when the bow
will face to the right and B parts
(optional parts) when the bow will face to the left.
Parts
-
Parts
-
Fold once and glue the folds together,
then give the sails a bulging appearance.
If you plan to have the bow face to the right,
curl the sails so that surface A will bulge out.
If the bow will face to the left, curl the sails
so that surface B will bulge out.
For parts 62 - 64, choose A parts
(standard parts) or B parts (optional parts)
depending on the direction in which
the bow will point.
Attach parts 65 - 70 (the yards) to the vessel masts. If the bow will
point to the right, attach the yards so that surface A is on top.
If the bow will face to the left, attach so that surface B is on top.
Glue the yards in place at an angle, as shown in the illustration,
so that the model will resemble a ship sailing in the wind.
Surface A on top
(bow pointed to the right)
Surface B on top
(bow pointed to
the left)
©Canon Inc. ©M. Nishiguchi/SENAUN
Ships of the world : Nippon Maru : Assembly Instructions
Glue parts 71 - 76 (square sails) after folding them once. As shown in the illustration,
to give the appearance of wind in the sails curl them vertically,
and then shape them to make them bulge from the center toward the outside.
Parts
-
Finished!
Glue the rear sides
of these parts together.
National Institute For Sea Training
With the cooperation of the National Institute For Sea Training
Nippon Maru
training vessel
National Institute For Sea Training
With the cooperation of the National Institute For Sea Training
Nippon Maru
training vessel
National Institute For Sea Training
With the cooperation of the National Institute For Sea Training
Nippon Maru
training vessel
Autres manuels Canon Jouet
Canon
Canon CREATIVE PARK Bird Cage Canary Manuel utilisateur
Canon
Canon creative park Manuel utilisateur
Canon
Canon Creative Park Ships of the world Esmeralda Manuel utilisateur
Canon
Canon Creative Park Halloween Wreath Manuel utilisateur
Canon
Canon CREATIVE PARK Yajirobe Manuel utilisateur
Canon
Canon PaperCraft White striped longhorn beeetle Manuel utilisateur
Canon
Canon Creative Park Elastic-powered Bus Guide de démarrage rapide
Canon
Canon CREATIVE PARK New Baby Manuel utilisateur
Canon
Canon Sidewheeler Guide de configuration
Canon
Canon Creative Park Easter Bunny Egg Holder Manuel utilisateur
Canon
Canon Jaguar E-Type Manuel utilisateur
Canon
Canon Paper Craft Manuel utilisateur
Canon
Canon Creative Park Teddy Bear Manuel utilisateur
Canon
Canon Creative Park Shaky-Shaky Maracas Manuel utilisateur
Canon
Canon CREATIVE PARK Sea lion Manuel utilisateur
Canon
Canon Creative Park Elastic-powered Turtle Manuel utilisateur
Canon
Canon CREATIVE PARK Sumo wrestling game Manuel utilisateur
Canon
Canon CREATIVE PARK Komatsu Special Vehicle 04... Manuel utilisateur
Canon
Canon CREATIVE PARK 3D Paper Mosaic (Tropical... Manuel utilisateur
Canon
Canon CREATIVE PARK Fractional Cake Manuel utilisateur
